Starter help

[part-time-Farmer-NC]

Maybe reach out to Valeo directly?

Contact

Customer Service:
Phone: 1-888-718-2536

Technical Support:
Phone: 1-888-718-2536, Press 2

 

[flyerdan]

First test would be to ohm out the big terminals, it should be infinite with it off the starter. If there is zero or little resistance, I would suspect that the disc has arced against the contacts and is not releasing, which would give the condition indicated.
Unfortunately, the solenoid pictured has a crimped end holding the bakelite end cap in so taking it apart and cleaning it would be rather difficult. But for $700, I'd spend a fair amount of time with a beveled file tang taking that crimp out so it can be serviced.

 

[MinnesotaEric]

First I'd put a remote starter on the starter and test the function on the machine to confirm that it is the solenoid and not something else. If no crank jumping the solenoid, then you can ohm it out out as others have suggested. If confirmed solenoid either call your local rebuilder or call that # for the company that was posted.

The long and short is a good parts person where mechanics go may also be able to find the equivalent.

Also, the link goes to the remote starter switch I use.

 

[Arrowsic21]

I'm having the same problem. What was your solution?

 

[IH3444]

New KIOTI solenoid for E5500-63016 starter on CK, DK, LK, NX, & RX tractors | eBay

This starter is used on various Kioti tractor models, including the CK, DK, and LK series. Why replace the whole starter when you could get a new solenoid for a fraction of the cost of a starter?. CK3510 Tractor STARTER MOTOR GROUP T5810-G711A.

www.ebay.com

 

[3StrikesNC]

Just found this thread. I’m now in this boat, starter main lug to the starter housing is a dead short. Guess it’s rebuild the starter of was just quoted about $500+ by Kioti dealer. CK 3510 H

 

[flyerdan]

It looks like the bakelite housing will come off the back of that solenoid. You should be able to take it apart and clean the copper bolts and plunger. If it's a direct short, the plunger is probably slightly spot welded to one of the bolts by arcing and will free up and work normally when cleaned up. If the bolt heads are eroded, they can be carefully tapped out and rotated so the new part faces in.

 

[MinnesotaEric]

Since misery loves company....

Some time ago, I had my tractor up at my Tinkerage to do the major hy-tran service and to puzzle out a mystery hy-tran leak. Long story short: after puzzling out the hytran leak, getting my local mechanical shop to rebuild Kioti's un-rebuildable lift cylinder for a song, and doing the hy-tran service, the stupid tractor stopped starting with the key. Key on, I can use a remote starter to start it, but no key start.

So I know:

(1) the starter solenoid is good because I can jump it.
(2) The ECU is ready to work once running (like cars, it may have a start map that is different than the run map—and yes, it is a diesel, and I'm saying "map" so work with it)
(3) and obviously the fuel shut off solenoid isn't trying to shut off since I can start it by jumping the starter solenoid.

My trouble is that my NX, being the 44th one made, is extremely early, and the service manual I have doesn't quite cover early HST models as accurately as a guy would hope (cf. front axle differences et el.). Moreover, Kioti in the manual I have talks about a "starter relay" that I don't have (unless starter relay is Kioti speak for starter solenoid) and a "safety start relay" that sounds like it is for gear models. If I have it, I have no idea where it is. My relays are under the hood and in the fuse box in the cab and I know what each of those does....

Anyway, while I'm certain my no-start problem is unbelievably simple, since I cannot talk to the ECU to find out what it thinks is missing, I'm left puzzling.