Snow plow and mount for Kubota B7510

   / Snow plow and mount for Kubota B7510 #21  
Although the MMM mounts might be strong enough, I would avoid relying on them. If they won't handle the stress you have then destroyed your ability to mount the MMM. I guess that also would be determined by your intent with the plow. I want to build something strong enough to push dirt/brush, etc. so will not use those mounts.

Thanks again for the pics and info.
 
   / Snow plow and mount for Kubota B7510 #22  
hey ASGAR, Could you post up some dimensions? Or better yet an itemized materials list? :D I'm gonna see if I can get my steel tomorrow, I sent you an email but I didn't want to rush you. I think that I can eyeball most of the pieces though.

I'm thinking:
2 --1.75"x6" ---8" tall C channels for the front subframe mounts
2 -- 2"X4"x.25" ---4' long tube for the main rails
1 -- 2"x4"x.25" ---22" long cross piece for rear of subframe
2 -- 1.75"x6" ---8" long C channel "wings" for plow mounts
1 -- 2"(i.d.)x.25" ---6" long Square tube for receiver
1 -- 2"x.375" ---6" long flat stock for receiver back cap/brace
2-- 2"x.25" ---8" long Caps/mounting tabs for rear mounts
2 -- 2"x.5" ---6" long Flat stock for outside snow plow mounts
2 -- 2"x.5" ---2" long Flat stock for inside snow plow mounts
1 -- 2"x4"x.25" ---4" long Brace between front of frame rails
1 --8"x10"x.125" --- Plate to tie front of mount together
2 -- 2"x.25"? ---10" Flat stock for bracing for plow mounts




Anybody see anything in that list that looks off? I tried to describe it as best I could. That pretty much sums up the steel except the hardware needed to mount the sub-frame. I didn't get to the hydraulic mount yet either.

This is my first post btw!:)
 
   / Snow plow and mount for Kubota B7510
  • Thread Starter
#23  
Ok, RedNeckRacin....

Earlier it was noticed that I had this frame in my house to take the pics... understanding wife and all... well tonight is her b'day but, for you, I headed out to the barn at 11pm......
Good estimates from the pics...

The actual measurements are:

2 --1.75"x4" ---7-1/4" tall C channels for the front subframe mounts
2 -- 2"X4"x1/8" ---34" long tube for the main rails
1 -- 2"x4"x1/8" ---13-1/2" long cross piece for rear of subframe
2 -- 1.75"x4" ---6" long C channel "wings" for plow mounts
1 -- 2"(i.d.)x.25" ---5-1/4" long Square tube for receiver
1 -- 2"x.375" ---5-1/2" long flat stock for receiver back cap/brace
2-- 2"x.1/2" ---9" long Caps/mounting tabs for rear mounts
2 -- 2"x.5" ---6" long Flat stock for outside snow plow mounts
2 -- 2"x.5" ---2" long Flat stock for inside snow plow mounts
1 -- 2"x4"x1/8" ---3-1/2" long Brace between front of frame rails
1 --5-1/2"x10"x3/16" --- Plate to tie front of mount together
2 -- 2"x3/8"? ---8" Flat stock for bracing for plow mounts

For the lift:
Tube hieght is 25", lift arm 18"
cylinder is a 2" dia x 8" stroke

Look at the pics.. now that I have used it a few times I found I do rub the front tires with the wheel cranked over so I am going to cut off the ends, see pic with black tape, the edge of the tape will be the cut line, you can see the rubs in the pic. Then I am going to weld on hangers from the front of the frame, see cardboard mock up. I also took a pic from the side to show that what I was trying to do was to get the plow frame pivot pins as close to the front of the tractor as possible. The 1/8" tubing is already overkill.
 

Attachments

  • P1010155.JPG
    P1010155.JPG
    70 KB · Views: 1,495
  • P1010157.JPG
    P1010157.JPG
    68.6 KB · Views: 1,254
  • P1010158.JPG
    P1010158.JPG
    70.5 KB · Views: 1,267
  • P1010159.JPG
    P1010159.JPG
    68.7 KB · Views: 1,128
  • P1010160.JPG
    P1010160.JPG
    74.8 KB · Views: 1,291
   / Snow plow and mount for Kubota B7510
  • Thread Starter
#24  
...And a few more pics....

Hope this helps.

Good luck, have fun building....
 

Attachments

  • P1010163.JPG
    P1010163.JPG
    66.4 KB · Views: 1,207
  • P1010164.JPG
    P1010164.JPG
    69.9 KB · Views: 978
  • P1010165.JPG
    P1010165.JPG
    65.5 KB · Views: 905
  • P1010168.JPG
    P1010168.JPG
    66.2 KB · Views: 977
  • P1010169.JPG
    P1010169.JPG
    69.8 KB · Views: 805
  • P1010170.JPG
    P1010170.JPG
    70.5 KB · Views: 788
  • P1010172.JPG
    P1010172.JPG
    67.4 KB · Views: 740
  • P1010174.JPG
    P1010174.JPG
    66.6 KB · Views: 730
  • P1010179.JPG
    P1010179.JPG
    63 KB · Views: 737
  • P1010180.JPG
    P1010180.JPG
    68.4 KB · Views: 1,049
   / Snow plow and mount for Kubota B7510 #26  
ASGAR FTW!!! :D
 
   / Snow plow and mount for Kubota B7510 #27  
Well I got it done. Only took me about 12 hours:eek: Asgar you should have told me this was an easy one lol I got a free snowplow while I was at it. I think its a little bit big from the pics but it cleaned the driveway in two passes! :D

Only problem I had was getting the front posts even. That should be taken care of tomorrow. I'm gonna look into getting a cleaner/easier to fix plow though.

Thanks for your help!


If anybody cares, I can post bigger pics up :) I took a video as well :)
 

Attachments

  • DSCN0077edit.JPG
    DSCN0077edit.JPG
    64.8 KB · Views: 1,256
  • DSCN0080edit.JPG
    DSCN0080edit.JPG
    74.2 KB · Views: 1,031
  • DSCN0086edit.JPG
    DSCN0086edit.JPG
    78.1 KB · Views: 970
  • DSCN0087edit.JPG
    DSCN0087edit.JPG
    61.5 KB · Views: 956
  • DSCN0088edit.JPG
    DSCN0088edit.JPG
    64.2 KB · Views: 1,037
   / Snow plow and mount for Kubota B7510 #28  
   / Snow plow and mount for Kubota B7510 #29  
Here is my BX1850 front hitch hookup. It uses the 3PH to raise and lower blade and is a manual angle.
 

Attachments

  • blade6.jpg
    blade6.jpg
    612.9 KB · Views: 1,571
  • blade9.jpg
    blade9.jpg
    735.3 KB · Views: 1,483
   / Snow plow and mount for Kubota B7510 #30  
Can you show a pic of the rear, how the 3pt moves that rod. I'm getting an idea from seeing your set-up.
JB.
 

Tractor & Equipment Auctions

2015 FREIGHTLINER CASCADIA (A50854)
2015 FREIGHTLINER...
HONDA EU2200 INVERTER (A50854)
HONDA EU2200...
2021 Snake River 14K Dump Trailer (A49461)
2021 Snake River...
2020 FREIGHTLINER 26FT BOX TRUCK (A51219)
2020 FREIGHTLINER...
2010 POLARIS RANGER 4X4 4 SEATER UTV (A51222)
2010 POLARIS...
2017 TRAILSTAR END DUMP TRAILER (A50854)
2017 TRAILSTAR END...
 
Top