Pictures of older and well-cared for tractors?

[sixdogs]

Any pictures of your older tractors that have been well cared for or restored? It's subjective but maybe 10 years and older?

 

[ptsg]

Ok. I start.

1970's Kubota B7000.

Mostly cosmetic restoration but fixed some stuff here and there as well. Just realized I've never took any good pictures of it restored. It had a third function that I used to run an homemade hydraulic broom attached to the bucket.

1962 Toselli 226 crawler tractor.

Full restoration, the only think not taken apart was the engine and the gearbox but changed the seals on those. Had a bad band brake on one of the tractors, broken final drive casting and some minor issues here and there. Most just wear from lack of maintenance.

1970-ish Agria 8900D articulated tractor.

My most recent project. Full restoration, pretty much everything was torn apart, clean, inspected, fixed and put back together. This one had a broken valve shoved through the head, center joint has so much play that was ready to come apart on its own, along with various other issues.

 

[BackRoad]

65 years old and still earning its keep...

 

[John0829]

My 60+ Mutt. Called Mutt because he has a 64' engine, 56' transmission and 57' differential. My go to tractor used several times each week except in the cold, then we both stay inside.

 

[sixdogs]

Ok. I start.

1970's Kubota B7000.

Mostly cosmetic restoration but fixed some stuff here and there as well. Just realized I've never took any good pictures of it restored. It had a third function that I used to run an homemade hydraulic broom attached to the bucket.

View attachment 873432


1962 Toselli 226 crawler tractor.

Full restoration, the only think not taken apart was the engine and the gearbox but changed the seals on those. Had a bad band brake on one of the tractors, broken final drive casting and some minor issues here and there. Most just wear from lack of maintenance.

View attachment 873434

1970-ish Agria 8900D articulated tractor.

My most recent project. Full restoration, pretty much everything was torn apart, clean, inspected, fixed and put back together. This one had a broken valve shoved through the head, center joint has so much play that was ready to come apart on its own, along with various other issues.

View attachment 873435

What a great crawler. Was that likely used in a vineyard? Any before pics?

 

[masscity]

My 1978 B7100DT I bought new. Use it for box blading and my CMI dump trailer on the front.

The 1958 Ferguson, use it for brush hogging only, used to belong to my Uncle and I operated it when I was a teen. He must have overhauled it, because the engine has like new compression and runs great.

 

[CalG]

Any pictures of your older tractors that have been well cared for or restored? It's subjective but maybe 10 years and older?

Old gal still pushing the snow around

http://i882.photobucket.com/albums/ac25/CalG52/P1010008_zps0bdd459d.jpg http://i882.photobucket.com/albums/ac25/CalG52/P1010002_zpsd983a185.jpg Fordson E27n It was a pleasant day in Vermont

www.tractorbynet.com

1950 Fordson E27n

 

[CalG]

 

[ptsg]

What a great crawler. Was that likely used in a vineyard? Any before pics?

Don't know much of the history of this tractor in particular but indeed these are used in vineyards on hillside and also on hillside farming.

Previous owner started "painting" it but then gave up. Good thing as he was painting it over dirt, grease and oil leaks. It also had an huge mouse next inside the duct for the fan, as this engine is air cooled.

 

[sixdogs]

Don't know much of the history of this tractor in particular but indeed these are used in vineyards on hillside and also on hillside farming.

Previous owner started "painting" it but then gave up. Good thing as he was painting it over dirt, grease and oil leaks. It also had an huge mouse next inside the duct for the fan, as this engine is air cooled.

View attachment 873538

You are lucky to have that crawler. My extended family grew grapes and there was a time when I wanted an Italian crawler really bad. I could never find one and after a few years I got over it. They are very handy little machines even if you only restore it and look at it every now and then.

 

[Jstpssng]

Not as bad as it looks, this TO35 ran well even though it needed a carb and waterpump. I replaced those, then realized it didn't make sense to put the 65+year old radiator back on. I'm waiting for a check for some wood I sold, then will order a new radiator.

This was my father's, after he passed away I told my mother that if I could have just one thing of his it was his Ferguson.

 

[ptsg]

You are lucky to have that crawler. My extended family grew grapes and there was a time when I wanted an Italian crawler really bad. I could never find one and after a few years I got over it. They are very handy little machines even if you only restore it and look at it every now and then.

I don't own it anymore but for a 1962 tractor, it was actually very well equipped. It had a 8x2 transmission with 2 speed PTO, 3 pt hitch, swinging draw bar and a single acting remote.

At the time I finish the restoration, I end up finding the big brother of that Toselli for very little money. It was the Toselli 336, nearly the same as the 226 but with a 3 cylinder 40HP 2.4L VM engine instead of the 2 cylinder 28HP 1.7L one. That 336 had a lot of wear in the engine and in the tracks.

Shortly after, I sold the 336 and traded the Kubota along with the 226 to get the new Branson.

These small crawlers are indeed very cool to have, but a pain to move around if you have to drive over any sort of surface that you care about. I had to move it over tarmac quite often and got to the point I built a low bed trailer just to move the crawlers around. The Italians will put rubber blocks on the tracks and drive those things on the road.

Too bad they no longer make these crawlers is smaller sizes/hp. I believe there is still market for those here in Europe. If I recall correctly, the smallest crawler now made is a 70HP one but back in the day, there were a lot of them starting around 20-ish HP. Same, Lamborghini, Fiat are probably the most sought after.

The mechanical curious part of me, kinda regrets selling the 336 before digging into the engine just to check the condition.

 

[gstrom99]

Not as bad as it looks, this TO35 ran well even though it needed a carb and waterpump. I replaced those, then realized it didn't make sense to put the 65+year old radiator back on. I'm waiting for a check for some wood I sold, then will order a new radiator.

This was my father's, after he passed away I told my mother that if I could have just one thing of his it was his Ferguson.

I had the local radiator shop re-core the radiator in this, when needed.

 

[CalG]

I don't own it anymore but for a 1962 tractor, it was actually very well equipped. It had a 8x2 transmission with 2 speed PTO, 3 pt hitch, swinging draw bar and a single acting remote.

At the time I finish the restoration, I end up finding the big brother of that Toselli for very little money. It was the Toselli 336, nearly the same as the 226 but with a 3 cylinder 40HP 2.4L VM engine instead of the 2 cylinder 28HP 1.7L one. That 336 had a lot of wear in the engine and in the tracks.

Shortly after, I sold the 336 and traded the Kubota along with the 226 to get the new Branson.

These small crawlers are indeed very cool to have, but a pain to move around if you have to drive over any sort of surface that you care about. I had to move it over tarmac quite often and got to the point I built a low bed trailer just to move the crawlers around. The Italians will put rubber blocks on the tracks and drive those things on the road.

Too bad they no longer make these crawlers is smaller sizes/hp. I believe there is still market for those here in Europe. If I recall correctly, the smallest crawler now made is a 70HP one but back in the day, there were a lot of them starting around 20-ish HP. Same, Lamborghini, Fiat are probably the most sought after.

The mechanical curious part of me, kinda regrets selling the 336 before digging into the engine just to check the condition.

View attachment 873550

Many years ago I spent a couple of weeks outside of Rome.
I often encountered small tracked tractors on the roadways. They would be sporting a pair of large diameter rubber tired wheels bolted to the rear track wheel , along with a heavy duty castor frame mounted up front. Seemed to work OK, and could imagine all it took to make the transition is a log or timber to drive over finding a balance point. /. ^

 

[ptsg]

Many years ago I spent a couple of weeks outside of Rome.
I often encountered small tracked tractors on the roadways. They would be sporting a pair of large diameter rubber tired wheels bolted to the rear track wheel , along with a heavy duty castor frame mounted up front. Seemed to work OK, and could imagine all it took to make the transition is a log or timber to drive over finding a balance point. /. ^

That's indeed another of doing it. I believe I have pictures of that saved. Like you said, all it takes is a wood block or a log and it doesn't even need a jack.

Here it is:

 

[LouNY]

Farmall 560 bought new by my father around 1960,

My IH 574 beleive her to be a 1974 Model

Ford 8000 my father bought in late 1968

Another 1974 model IH 1066 my brother picked up a few years ago (5-10)

And several more over at the farm still in use;
Farmall 400, Farmall H, IH 656's, then the IH Magnums 7110,7130,7220 (late 80's) all of them still worked.
Then there are a couple of Deere's a 4020, a pair of 4430's
Then the IH Puma 125 and NH 6050 are the "newer" ones they are well over 10 years old.

Then there is this ol girl, she's a 1955 AC WD45 not a working tractor but she will pull!!!

 

[Tinhack]

Here's my 1986 Ford 3910 I completed back in 2021. It starts with just a touch of the key. I also have a 1956 JD 420C with a hydraulic crane and dozer blade. It lived life as a pipe-layer. I haven't restored it yet and I'm getting too old to sling track around, but it could use new steering clutches.

 

[bmaverick]

My 1981 Yanmar YM2610,

If you live in the south, you too can have any of the models in restored to better than new, 13Hp up to 70Hp.

Fredricks Importing

Fredricks Importing is the best source for grey market Yanmar Tractors and Yanmar Tractor Parts. Call us at 256-751-3555 and we'll get you everything you need. Dealer inquiries welcome!

www.fredricksimporting.com

 

[David Wayne]

My Jetstar is '67 and the 630 is '59

 

[sixdogs]

Wow, those are some nice tractors.