Need kubota L2850 wiring harness

   / Need kubota L2850 wiring harness
  • Thread Starter
#11  
Got the fuel shut off solinode installed but the timer relay that drives it is shot... which is $78 to $94 in addition to the $63 we already spent on the solinode.

Spent a little time starting the process of straightening sheetmetal... lost cause. But I'll give it an honest effort...
 
   / Need kubota L2850 wiring harness
  • Thread Starter
#12  
One step forward two steps back it looks like....



Poor ol tractor lives it's whole life outside... only gets to come inside for repairs, bet it thinks of indoor parking like some of us think of going to the dentist!

Repaired the radiator today, one of the steel brackets on the side came lose, I soldered it back on, and straighted some fins. Going to replace all the hoses and alt belt. Removed, cleaned, and painted the battery tray.
 
   / Need kubota L2850 wiring harness
  • Thread Starter
#13  


Front axle was leaking at the bottom of the wheel pivot points. Further inspection brought to light bad bearings as well. Disassembled both sides and ordered the parts needed. Gears and all other bearings seemed ok... will replace all seals while its apart.
 
   / Need kubota L2850 wiring harness
  • Thread Starter
#14  
Only got about half a day on the tractor today... straightened a few dents and wrinkled panels around the dash area, and hood and side panels. Grill is gonna take some work...
Axle bearings came late in the day, will start assembly tomorrow morning. Still waiting on 2 of the 4 radiator hoses and alt belt.
 
   / Need kubota L2850 wiring harness
  • Thread Starter
#15  
Front axle is back together and full of oil... assembly went easily, was done by lunchtime.


Afternoon was spent working on cleaning rusty headlight buckets and grill repairs.
 
   / Need kubota L2850 wiring harness #16  
Get rid of the "voltage regulator" and all of "it's" wiring.
Install a GM alt with internal regulator, you'll be allot happier with it,
and you can loose half of that unneeded wiring.
 
   / Need kubota L2850 wiring harness
  • Thread Starter
#17  
If the alt ever goes bad, that may happen simply due to the cost of a replacement alt. They are 'spencive. Wish I could have done that when I had the harness completely cut up, less likely to be done properly now that its all back in the wire loom and neatly closed up.

Thanks for the idea.
 
   / Need kubota L2850 wiring harness
  • Thread Starter
#18  
Radiator hoses were replaced, new fan belt, new tail lights and made a wireing harness for them as well, as done as it's gonna get for now. First time in 15 years any lights have worked!

Grill was repaired, and headlight support straightened.




Made a new rad cap cover outta tread plate cause it was handy, and trim between headlights to match grill guard.




Facemask! No more grill damage!




Back out wearin his loader... Rufus L. Tractor is happy to be free again, headed out to haul wood, till gardens, and brush hog again.

 
   / Need kubota L2850 wiring harness #19  
That Ole' tractor looks better than it did when you started.
 
   / Need kubota L2850 wiring harness
  • Thread Starter
#20  
Thanks... boss just wanted a few basics taken care of this time around... hope to get it in for a paint job this winter or next... next year we could justify it with the bosses wife "every 30 years a good tractor deserves a paint job"

With a new starter and functioning glow plugs it fires right up now!
 

Tractor & Equipment Auctions

2005 Case IH 2062 Flex Draper Header (A50657)
2005 Case IH 2062...
2011 Liebherr L586 (A52128)
2011 Liebherr L586...
Kubota F3990 (A50322)
Kubota F3990 (A50322)
2018 CATERPILLAR 336FL EXCAVATOR (A51222)
2018 CATERPILLAR...
Quick Attach Pallet Forks (A47384)
Quick Attach...
UNUSED CFG Industrial MX15RX Mini Excavator (A47384)
UNUSED CFG...
 
Top