Making a Three Point Hitch

   / Making a Three Point Hitch
  • Thread Starter
#11  
Not sure where you are in Canada, but here in Alberta we have a business called GRATTON COULEE AGRI PARTS. The have a wide selection of goods.
They are in IRMA ALBERTA.
I have reached out to them and unfortunately no dice.
 
   / Making a Three Point Hitch
  • Thread Starter
#12  
Unfortunately I suspect it wasn’t until the later years of the 806 that they started offering them with the 3 point hookup option .
Does your 806 have the proper mounts for a 3 point hitch ?
It does not unfortunately, complete bareback with just a drawbar.
 
   / Making a Three Point Hitch #13  
You might be money ahead to buy a different tractor to run that mower or get a pull type mower for your 806.
 
   / Making a Three Point Hitch #14  
Probably enough here to design one that will work right.

Bruce
 

Attachments

  • 3-Pt Free Link standard.pdf
    171.1 KB · Views: 48
   / Making a Three Point Hitch
  • Thread Starter
#15  
Probably enough here to design one that will work right.

Bruce
Thank you, current design im using a singular 2x12 hydraulic cylinder and sticking to making it cat 1 as this will only be used for mowing pretty much. Appreciate that pdf.
 
   / Making a Three Point Hitch #17  
   / Making a Three Point Hitch #18  
Surprised to find so many "Wheatland" 806's were made. We got an early 806, big step up for a farm with a Case 400 diesel, 2 Farmall M's, 2 H's, and a Super A. Great to have a semi-mounted 5 bottom plow to replace the pull type. Having the spec sheet, I saw the Wheatland Special and wondered why someone would buy without 3 point, but so many customers had tractors like W9 and a 3-point was a waste. I have a friend, Bill Braunsworth, in Plato, MN, who resurrects dead IH tractors who likely has the stuff but you being in Canada, likely too expensive. Last time I was there he dozens of old IH tractors mostly robbed of engine and transmission parts with the rest of the carcasses stacked until he ran out of room and called the scrap man.
 
   / Making a Three Point Hitch #19  
Hello Everyone,

So my tractor(IH 806 w/ pto and rear hydraulics) I recently got only came with a drawbar, and I need a three point hitch to run a rough cut mower.
There used to be a company that made three point hitch but they are long gone and hard to find in Canada.

I was looking at making my own Cat 1 three point hitch (tractor is 100 hp but i dont really need higher category hitch)
I was wondering if anyone had any guidance or specifications documents on building three point hitches.
One of the ideas I had was to buy a three point hitch kit that kubota sells for its bx series and adding steel plating and having a 3x12 hydraulic cylinder. (Kubota #BX2506 3-Point Hitch Kit for BX25 / BX25D / BX23S Tractors).

If anyone has any ideas or guidance, much appreciated. Thank you
Maybe you should look for an old tow behind rough cut mower?
 

Tractor & Equipment Auctions

Unused Quick Attach Weldable Backing Plate (A48837)
Unused Quick...
2015 Ford Escape AWD SUV (A50324)
2015 Ford Escape...
(4) 8 Lung Dual Wheel and Tires (A48837)
(4) 8 Lung Dual...
JOHN DEERE 5085E TRACTOR (A50459)
JOHN DEERE 5085E...
2021 FREIGHTLINER CASCADIA 126 SLEEPER TRUCK (A50505)
2021 FREIGHTLINER...
(2) 480/70R28 TIRES ONLY (A50460)
(2) 480/70R28...
 
Top