67PLY
Silver Member
Any thoughts on the Mahindra 5 foot - 3 point hitch rotary mower ? - looked a one on Sunday at local dealer.
Mahindra rotary mower ......
- Thread starter 67PLY
- Start date
- Views: 12212
Sysop
Elite Member
- Joined
- Jun 7, 2013
- Messages
- 3,301
- Location
- Fairmont, WV
- Tractor
- Mahindra 4035HST purchased 2013 - Husqvarna TS348-D purchased 2019 - Craftsman 42" HST purchased 2003
The one they sold me for my 4035HST came with a Mahindra Max sticker on the side was actually made by Kodiak for Mahindra. It seems to be a good product.
OP
67PLY
Silver Member
Thanks - the one I looked at said SD or ST 60 Mahindra MAX - do you recall the $$$ ... ?
burzynsr
Gold Member
- Joined
- Jun 9, 2010
- Messages
- 270
- Location
- Grimes county Texas
- Tractor
- Mahindra 4025 / Kubota RTV500 / Bad Boy ZT Elite 60"
I have a 6 foot Mahindra SD (standard duty) made buy Kodiak and have not had any issues with it. I paid $1350.00 for it last April.
OP
67PLY
Silver Member
The 5 foot SD model I looked on Monday sells for $ 1150.00 - really fair price. Looks like the back is open ... rear discharge like our old woods mower. Our tractor is around 28 hp - not sure if it could pull a 6 fioot in high grass. Thanks for your input.
TnWV
Platinum Member
- Joined
- Apr 29, 2008
- Messages
- 588
- Location
- Liberty,WV - Putnam Co.
- Tractor
- 2003 Zetor 4341 w/FEL, 1970 MF 150, 2012 JD X530
I have a Kodiak HD8. It's been great for the 2.5 years I have had it. Seems well built.
I have a Max 25. It easily handled a 5 ft rear mount bush hog. It also has a 5 ft mid mount mower and I have only once choked it out that I've killed the engine. A rear mount mount runs at lower RPMs. I don't think a 6 ft would be a problem.
The next question to ask is "Does the extra foot make a difference in getting the job done for the money?"
Sysop
Elite Member
- Joined
- Jun 7, 2013
- Messages
- 3,301
- Location
- Fairmont, WV
- Tractor
- Mahindra 4035HST purchased 2013 - Husqvarna TS348-D purchased 2019 - Craftsman 42" HST purchased 2003
Short answer, yes.
Long answer is to calculate the time exactly. How many passes with your 5 foot mower does it take to mow your area? How long does it take to make a single pass? How many passes are you going to save? That's how much time you can save.
Another way to look at it is for every 5 passes with a 6 foot mower, you've covered as much ground as 6 passes with a 5 foot mower.
Another consideration is maneuverability. Is there anyplace that is a tight fit with the 5 foot mower? A 6 foot would surely fit tighter.
I'm not disagreeing with you. I'm just pointing out whether is the extra $2-400 really worth it.
In my case the I'm finish mowing about 2 acres every week, and making a pass on the other 2 acres about every two-three weeks. The extra foot would probably save me about 15 minutes, maybe 30. Not a significant enough difference to me for the dollars. So I have to wait a little longer to put my steak on the grill. If it were 8-10 acres then I would probably cough for it. If I were doing 40 acres, I would go to the bat wing type mower that they use alongside the highway.
Again, it is what you value and where you're using it. :confused3:
nelsond7004
Silver Member
Hi 67PLY,
I have a Kodiak "Mahindra" stickered standard duty 5 foot rotary cutter with a slip clutch. I have had it for a little over a year and I have been very pleased with it. I have taken on more than what it is rated for and it is holding up very well. I looked at many different brands and I felt for the money this was one of the better built cutters.
My tractor has approximately 23hp at the PTO. Quite low, but it handles the 5 footer well. Tall grass can bog the tractor a bit, but anything else is no match. I think a 6 footer might be a bit much for your tractor.
Tax included, I paid $990 for the 5' with a slip clutch. I don't think you will be disappointed. My buddy just bought a 7' HD version and wow! Built twice as tough as a tank.
