Just another junk chainsaw

   / Just another junk chainsaw
  • Thread Starter
#2,141  
Morning Laugh in my chainsaw repair group.

We go through this all the time. Folks need to learn their chains they have or bring them in with them.

lolchains.jpg
 
   / Just another junk chainsaw #2,142  
Morning Laugh in my chainsaw repair group.

We go through this all the time. Folks need to learn their chains they have or bring them in with them.

View attachment 3371165
I bring my chain in. When I get a new chain I take the cover off the box and put it in the glove compartment.
Then clean the truck and throw it out! :LOL:
 
   / Just another junk chainsaw
  • Thread Starter
#2,143  
Got her stumped yesterday. G466 and G444 for the dirty work.

stump25.jpg
stump255.jpg
stump2555.jpg
g466444.jpg
 
   / Just another junk chainsaw
  • Thread Starter
#2,144  
Stump chunked.

Where I had cut was higher then measured at flare of 48". Ended up cutting 46x45.

Farmertec G444 even stock with their DP muffler is a beast.

g444stumpchunk.jpg
 
   / Just another junk chainsaw #2,145  
Stump chunked.

Where I had cut was higher then measured at flare of 48". Ended up cutting 46x45.

Farmertec G444 even stock with their DP muffler is a beast.

View attachment 3378858


Would you give the greenlight to buy a Farmertech big CC saw for running a 36” bar maybe 1-2 times/month? I don’t know if they offer one…..
 
   / Just another junk chainsaw #2,146  
Would you also give the green light to run one with an Alaskan saw mill? 80-90cc (whatever they make).
 
   / Just another junk chainsaw #2,147  
Would you also give the green light to run one with an Alaskan saw mill? 80-90cc (whatever they make).
They make up to 122cc MS880 clone G888
 
   / Just another junk chainsaw
  • Thread Starter
#2,148  
Would you also give the green light to run one with an Alaskan saw mill? 80-90cc (whatever they make).
Heck yes. I know guys been running them on mills for years. Some stock some modded.

You need to know your way around the older better chainsaws IMHO. How to tune, how to check over etc before using. Most are not plug and play like todays world. Heck even oem aint like that for me and echo's.

I would rather tear one of these up doing grunt work then a oem saw. Cheap to buy and cheap to fix.

G888 G660 G395 and now a G3120.

My G888 and G660 I had a local wanted for his mill set ups.

Guy I know in pic that makes a living milling.


g888chapppp.jpg
g888chapp.jpg
g888chappppp.jpg
g888chappp.jpg
g888chap.jpg
 
   / Just another junk chainsaw #2,149  
Would you also give the green light to run one with an Alaskan saw mill? 80-90cc (whatever they make).

They would probably work, for awhile.

What you want is this (below)...it's bomb proof and will last a very long time under heavy duty cycle. I just don't know if the chinaisium has all that much duty cycle.

20220710_085721.jpg
 
   / Just another junk chainsaw
  • Thread Starter
#2,150  
Would you give the greenlight to buy a Farmertech big CC saw for running a 36” bar maybe 1-2 times/month? I don’t know if they offer one…..
They have a Gen2 of the MS880. The later ones with 2 piece mufflers. I hated them when 088 and 880 gen1 had cast muffler set ups.

Being your a stihl first kind of guy. G888 with a 361 coil. Mine would take locals 088 lunch.

But smaller cheaper G395 pullds 36" like a beast in hardwoods. Save weight and cost. Then G660 but only ran 66 oem and clones up to 32" hardwoods.


Clones you need to know how to tune etc from get go. No one to set them up right for ya. Unless you buy from Jes MT and Scott PA in USA and tell them set saw up and prerun for you. www.bluesaws.com

No more blue ones though. All orange, orange grey, etc now though.




g888t.jpg
g888444466.jpg
g888cb.jpg
g3953666.jpg
g66032.jpg
 

Tractor & Equipment Auctions

2014 Volkswagen Passat Sedan (A50324)
2014 Volkswagen...
2013 INTERNATIONAL WORKSTAR 7600 SBA 6X4 DUMP TRK (A51406)
2013 INTERNATIONAL...
2019 Ford F-150 4X4 (A50397)
2019 Ford F-150...
2014 TOYOTA 8FGCU25 FORKLIFT (A51222)
2014 TOYOTA...
3000 Gallon Black Poly Water Tank (A49461)
3000 Gallon Black...
2003 Big Tex 10PI 16ft. T/A Pipe Top Utility Trailer (A49461)
2003 Big Tex 10PI...
 
Top