HST Power ?

[Hilbilly]

I recently traded my open station 47 hp Powershift tractor for a 49 hp HST tractor with cab. I love this thing but find there seems to be less power available. For most things so far it hasn't been an issue but yesterday I was using the boxblade to smooth out the driveway and thought there was a significant difference between the power of the gear tractor and the HST. The bottom of our driveway is about 15% grade and on the way down I could pull a full load on the 7ft boxblade in 2WD and mid range. On the way back up it was low range 4WD and struggling to keep the speed between 3 - 4 kmh.

Question is: if I had more hp would that improve significantly or is that just the sacrifice of having HST? I'm considering upgrading to a 60 hp HST from the 50 hp HST but don't want to spend a bunch more money and then find out there was not much of an improvement.

 

[jeff9366]

I recently traded my open station 47 hp Powershift tractor for a 49 hp HST tractor with cab.

I love this thing but there seems to be less power available.

Bear in mind a tractor cab weighs 600 to 700 pounds more than same model open station tractor. Your performance loss is more likely due to the additional weight of the cab than anything doing with the HST.

To notice a significant improvement pulling uphill with your Box Blade you will need at least 75 horsepower. Horsepower is always quoted at max performance but we seldom operate our tractors that way. You will NOT notice more than a minor improvement with an increase from 50 to 60 horsepower, assuming traction does not become a problem.

You should also research DRAWBAR HORSEPOWER for the tractor you have and the tractor(s) you are considering. Some tractor manufactures have 20% more efficient transmissions than others. Drawbar horsepower indicates "real world" pulling power.

Kubota is known for efficient HST transmissions but check yourself.

 

[MossRoad]

I recently traded my open station 47 hp Powershift tractor for a 49 hp HST tractor with cab. I love this thing but find there seems to be less power available. For most things so far it hasn't been an issue but yesterday I was using the boxblade to smooth out the driveway and thought there was a significant difference between the power of the gear tractor and the HST. The bottom of our driveway is about 15% grade and on the way down I could pull a full load on the 7ft boxblade in 2WD and mid range. On the way back up it was low range 4WD and struggling to keep the speed between 3 - 4 kmh.

Question is: if I had more hp would that improve significantly or is that just the sacrifice of having HST? I'm considering upgrading to a 60 hp HST from the 50 hp HST but don't want to spend a bunch more money and then find out there was not much of an improvement.

What make and model of tractor is it?
How old is it?
How many hours are on it?
Have the fluids and filters in the transmission been changed lately?
Things like that....?

 

[LouNY]

I recently traded my open station 47 hp Powershift tractor for a 49 hp HST tractor with cab. I love this thing but find there seems to be less power available. For most things so far it hasn't been an issue but yesterday I was using the boxblade to smooth out the driveway and thought there was a significant difference between the power of the gear tractor and the HST. The bottom of our driveway is about 15% grade and on the way down I could pull a full load on the 7ft boxblade in 2WD and mid range. On the way back up it was low range 4WD and struggling to keep the speed between 3 - 4 kmh.

Question is: if I had more hp would that improve significantly or is that just the sacrifice of having HST? I'm considering upgrading to a 60 hp HST from the 50 hp HST but don't want to spend a bunch more money and then find out there was not much of an improvement.

Thats a 10 Hp change some say thats not much, it's also 20% which sounds like more.
I believe that you would feel the difference but the hydro's have always sucked up a bit of horsepower.
And pulling up a grade with a load does take hp.

 

[CobyRupert]

OP isn't treating the hydro pedal like a gas pedal.....right?
(i.e. don't push pedal down more as tractor slows down, instead lift pedal for the "shift to lower gear" equivalent.)
He wouldn't be the first.

 

[ericm979]

HST tractors with linked throttle and HST pedal muddle that up even more.

When I am doing something ground engaging or going up a steep hill I set the throttle to PTO RPM with the hand lever and use the HST to modulate speed.

 

[ArlyA]

HST does rob a bit of your HP. I can't recall the numbers for sure and it depends on where you are in the power curve, but its in the 15 to 30% loss area. The higher percent loss is while doing max engine RPM and the HST maxed at the same time.

 

[Hilbilly]

Lots of good points / questions.

I forgot about the cab adding more weight. That combined with the bigger loaded tires adds about 800 lbs to this tractor and that's quite a bit. I recall adding that much to the 3PTH on the old tractor and noticing the difference.

The tractor is a 2015 1749 Massey with 230 hrs on it. I replaced all the fluids and filters when I got it and have put about 30 hrs on it since then.

I also thought that a 20% increase in power would be noticeable but maybe not. There's no way I can find out either since the dealers around here don't have anything I could try. The Massey dealer only has one tractor in the 40 to 60 hp class and it is the same one I have, just a year newer and the Kubota dealer doesn't have any tractors in that size.

Good points about the linked throttle and the HST pedal not being an acceleration pedal. It took me a bit to realize that the transmission needs higher rpm to work properly and to get the feel of using the HST pedal. When working it hard I have the throttle set at PTO rpms and monitor the tach to control the HST pedal position. When the rpms start to drop I back off the HST pedal until the rpms get back to PTO speed. It's a balancing act and I have that figured out.

 

[Hilbilly]

HST does rob a bit of your HP. I can't recall the numbers for sure and it depends on where you are in the power curve, but its in the 15 to 30% loss area. The higher percent loss is while doing max engine RPM and the HST maxed at the same time.

30% is a HUGE loss!

 

[MossRoad]

Lots of good points / questions.

I forgot about the cab adding more weight. That combined with the bigger loaded tires adds about 800 lbs to this tractor and that's quite a bit. I recall adding that much to the 3PTH on the old tractor and noticing the difference.

The tractor is a 2015 1749 Massey with 230 hrs on it. I replaced all the fluids and filters when I got it and have put about 30 hrs on it since then.

I also thought that a 20% increase in power would be noticeable but maybe not. There's no way I can find out either since the dealers around here don't have anything I could try. The Massey dealer only has one tractor in the 40 to 60 hp class and it is the same one I have, just a year newer and the Kubota dealer doesn't have any tractors in that size.

Good points about the linked throttle and the HST pedal not being an acceleration pedal. It took me a bit to realize that the transmission needs higher rpm to work properly and to get the feel of using the HST pedal. When working it hard I have the throttle set at PTO rpms and monitor the tach to control the HST pedal position. When the rpms start to drop I back off the HST pedal until the rpms get back to PTO speed. It's a balancing act and I have that figured out.

You say you have it at PTO speed. Have you tried it at higher engine RPMs? My late 70s IH2500b was HST. It had a hand throttle (like most tractors) that I'd set at PTO speed. And it had a foot throttle that I could give it more gas if my engine RPMs started to drop or I needed more power to, say, climb up a hill. Of course, I could also set the hand throttle for max RPMs as well.

So, again, I'll ask if you've tried it at higher engine RPMs than PTO RPMs.?