FOPS Mounted Cooling Fan

   / FOPS Mounted Cooling Fan #1  

SpringHollow

Elite Member
Joined
Dec 9, 2006
Messages
2,638
Location
South of Rochester, NY
Tractor
Power Trac 1850, NH 2120
Someday, I will get caught up with posts.

The previous owner of my PT1850 ground off the oil cooler fan mounts so that he could use cheap fans made in China. These fans do not last long and I got tired of replacing them. I 3D printed some adapter brackets so I could use his mounting studs to mount the SPAL fan. A Deutsch style connector was used to wire the fan. I got a good deal on a two pack of SPAL fans so I decided to use the spare fan to cool the operator when desired. Under the FOPS seemed like the best location, so I printed some 1" spacers to allow airflow around the fan. The fan is mounted using magnets. Originally, I tried 1" magnets. They held until a major jarring occurred like going very fast over a large bump or dropping the tractor when it is lifted up by the mini hoe. So I replaced those magnets with 1.25" (1.26) magnets. These make it difficult to remove the fan but it can be done.

For power, I installed two 12V sockets that are supposedly weather rated. One is always on and the other is controlled by the ignition switch. (Previously, I had added a relay that is controlled by the ignition switch in order to run various accessories.) The plug on the fan has an on/off switch integral to the plug. The fan is p.retty powerful and could become uncomfortable after a while if not wearing a hat. The magnets allow one to move the fan to the best location for the current activity. If doing a lot of driving, forward of the operator might be desired. I have been happy with this setup.

The tractor is covered in dust because I have been using it for a lot of dirt work lately. It has been so dry the last couple of months that there is no sign of moisture even 3' down. The clay breaks up into a fine dust that goes everywhere. I can not wait to be finished so I can give the PT a well deserved bath.
 

Attachments

  • Spal1.jpg
    Spal1.jpg
    1.8 MB · Views: 36
  • Spal2.jpg
    Spal2.jpg
    985.7 KB · Views: 34
  • Outlets.jpg
    Outlets.jpg
    1.8 MB · Views: 38
  • Plug.jpg
    Plug.jpg
    875.4 KB · Views: 38
  • Installed.jpg
    Installed.jpg
    929.5 KB · Views: 34
   / FOPS Mounted Cooling Fan #2  
Nice, now we all have info on china fans too.
 
   / FOPS Mounted Cooling Fan #4  
Nice. I have a spare fan and might copy this idea. Where did you get the switch and magnets? I could consider using magswitches, although they’re very expensive and I haven’t found a cheaper alternative. With that setup, the fan could be moved to other machines if needed. I tend to run hot, and my mini-x and CTL don’t have A/C. Adding a fan to those machines had already crossed my mind, so this could be a great solution.
 
   / FOPS Mounted Cooling Fan
  • Thread Starter
#5  

Tractor & Equipment Auctions

Toro Z Master 2000 Zero Turn Mower (A50324)
Toro Z Master 2000...
BUNDLE OF 6" I BEAMS UP TO 51" (A54756)
BUNDLE OF 6" I...
(3) ROLLS OF 4' GALVANIZED FIELD FENCE (A54757)
(3) ROLLS OF 4'...
2016 Godwin CD150M 6in Dri-Prime Pump S/A Trailer (A55851)
2016 Godwin CD150M...
2009 JOHN DEERE 544K WHEEL LOADER (A52705)
2009 JOHN DEERE...
2007 MACK CV713 WINCH TRUCK (A53843)
2007 MACK CV713...
 
Top