Can anyone identify
- Thread starter Ndonavan
- Start date
- Views: 652
airbiscuit
Super Member
- Joined
- Aug 28, 2004
- Messages
- 6,518
- Location
- NW Wisconsin
- Tractor
- New Holland T2310 (40hp), Kubota L3010 GST, New Holland TC21DA *** Previously - Farmall H, 1941 John Deere B, Shibaura SD1500, John Deere 850, Bobcat 642, New Holland 1925
Don't know, but I like the ratchet straps and the Whiskey. What parts are you needing?
airbiscuit
Super Member
- Joined
- Aug 28, 2004
- Messages
- 6,518
- Location
- NW Wisconsin
- Tractor
- New Holland T2310 (40hp), Kubota L3010 GST, New Holland TC21DA *** Previously - Farmall H, 1941 John Deere B, Shibaura SD1500, John Deere 850, Bobcat 642, New Holland 1925
Is it a snap ring, or more of a spacer? Maybe if you could post a couple of pics of the good part and the missing part, others could help.
rangerfredbob
Veteran Member
It doesn't look like the Massey or International discs I've seen, or deere or most others, fixed angle wheel discs aren't common from what I've seen at auction unless they're cover crop discs...
That said, I'm not sure what's going on, if it's loose where the strap is and if discs are loose you likely need a new bearing housing, from the looks of it it's plain bearings. As crazy as they look they're pretty common and cheap at I think Messics and Steiner or something, I don't remember... Most discs don't have "snap rings", everything is held together by the nut at one end of the shaft, if discs are loose that nut has worked loose or something in the middle is broken like a chipped spacer or bearing casting. Usually the bar the discs are mounted to is square, finding that square size is the key to ordering replacement parts, most of them are generic...
My brother got a 14' wide disc that had two bad bearings on one gang, these were ball bearings, stuff was loose too, after like $75 in parts we got it fixed and put back together, kinda a pain involving a giant chain wrench, big pipe wrench and big adjustable wrench and hammers but we got it done...
That said, I'm not sure what's going on, if it's loose where the strap is and if discs are loose you likely need a new bearing housing, from the looks of it it's plain bearings. As crazy as they look they're pretty common and cheap at I think Messics and Steiner or something, I don't remember... Most discs don't have "snap rings", everything is held together by the nut at one end of the shaft, if discs are loose that nut has worked loose or something in the middle is broken like a chipped spacer or bearing casting. Usually the bar the discs are mounted to is square, finding that square size is the key to ordering replacement parts, most of them are generic...
My brother got a 14' wide disc that had two bad bearings on one gang, these were ball bearings, stuff was loose too, after like $75 in parts we got it fixed and put back together, kinda a pain involving a giant chain wrench, big pipe wrench and big adjustable wrench and hammers but we got it done...
airbiscuit
Super Member
- Joined
- Aug 28, 2004
- Messages
- 6,518
- Location
- NW Wisconsin
- Tractor
- New Holland T2310 (40hp), Kubota L3010 GST, New Holland TC21DA *** Previously - Farmall H, 1941 John Deere B, Shibaura SD1500, John Deere 850, Bobcat 642, New Holland 1925
If it's a spacer, you could make one out of wood, saw it in half longitudinally, and clamp it on the axle as a temporary fix that would probably last for a long time.
stuckmotor
Super Member
- Joined
- Sep 23, 2009
- Messages
- 5,304
- Location
- Lower Up State S.C.
- Tractor
- AC WD 34 hp/3500 lbs MF 261 60 hp/5380 lbs
That disc has several similarities not the least being color, to an Allis Chalmers disc a neighbor had. I think his was made in the 1960's.