twinstackram
Silver Member
I was thinking about doing the same thing on our Ranger,nerf bars,rear bumpers,but wasn't sure that type of bender would work,but after looking at yours I think it will.
Brush Guard Project
- Thread starter GeneD14
- Start date
- Views: 6407
OP
GeneD14
Veteran Member
- Joined
- Jul 29, 2003
- Messages
- 1,458
- Location
- Tennessee
- Tractor
- Kubota B26 TLB, Allis Chalmers D17 series IV, Kubota ZG-23 Mower, Kubota ZD 1211, Kawasaki Mule 610, Stihl 361, Stihl 045 AV Super, and a Stihl 660 Ported and tuned
</font><font color="blue" class="small">( Heck !!!
If I had known you could do that I would have paid you $69 for my new Ford Grill Guard ! I am always a day late and a dollar short! Nice looking job ,Gene . )</font>
BigAl,
Thanks, I have only $30 in pipe in this project. I'm not sure I'm ready to make a truck brush guard.(at least not one worthy of a truck like yours) I will practice up some more. /forums/images/graemlins/grin.gif Total time on this project was about 5 hours. The bending part was just a few minutes.
If I had known you could do that I would have paid you $69 for my new Ford Grill Guard ! I am always a day late and a dollar short! Nice looking job ,Gene . )</font>
BigAl,
Thanks, I have only $30 in pipe in this project. I'm not sure I'm ready to make a truck brush guard.(at least not one worthy of a truck like yours) I will practice up some more. /forums/images/graemlins/grin.gif Total time on this project was about 5 hours. The bending part was just a few minutes.
SnowRidge
Elite Member
Ooohhh, you do nice work. I have to fabricate tree guards for our Power Trac before next season. I think I'll look into picking up one of those benders from HF.
OP
GeneD14
Veteran Member
- Joined
- Jul 29, 2003
- Messages
- 1,458
- Location
- Tennessee
- Tractor
- Kubota B26 TLB, Allis Chalmers D17 series IV, Kubota ZG-23 Mower, Kubota ZD 1211, Kawasaki Mule 610, Stihl 361, Stihl 045 AV Super, and a Stihl 660 Ported and tuned
</font><font color="blue" class="small">( I was thinking about doing the same thing on our Ranger,nerf bars,rear bumpers,but wasn't sure that type of bender would work,but after looking at yours I think it will.
)</font>
I think it would make great nerf bars out of 2" pipe. A few months ago I bought a set for my wife's Expedition and I wish that I would have waited and made them with the bender.
I would strongly recommend practicing on a scrap piece first.
)</font>
I think it would make great nerf bars out of 2" pipe. A few months ago I bought a set for my wife's Expedition and I wish that I would have waited and made them with the bender.
I would strongly recommend practicing on a scrap piece first.
OP
GeneD14
Veteran Member
- Joined
- Jul 29, 2003
- Messages
- 1,458
- Location
- Tennessee
- Tractor
- Kubota B26 TLB, Allis Chalmers D17 series IV, Kubota ZG-23 Mower, Kubota ZD 1211, Kawasaki Mule 610, Stihl 361, Stihl 045 AV Super, and a Stihl 660 Ported and tuned
Thanks everyone for the kind words. It is always fun using a new tool for the first time. After I finished this bending project I started thinking of other projects that I could use the bender on. /forums/images/graemlins/grin.gif
fig
Silver Member
Use it only a few times per year.....huh /forums/images/graemlins/smirk.gif /forums/images/graemlins/grin.gif /forums/images/graemlins/grin.gif! Looks good and already talking about other projects.
Fig
Fig
have_blue
Veteran Member
Gene, that's just neat, crisp, and sanitary. Highly functional too. It does my heart good to see work like that.
