wheels

I’m in the market to purchase a new set of aftermarket wheels for my 2014 F150. I’ve looked up the stock wheel size, and nothing seems to match up as far as backset/offset whatever you wanna call it. I don’t know if it’s my old age or what but I seem to get easily confused when I’m looking at...

Has anyone added deck wheels to their rear engine Snapper? Mine is 33". What wheel kit did you use?

Today I was about to backup on a slight slope and the rear wheels started to spin. I thought the front wheels might be locked up. I jacked the front end and the wheels spin freely. Any thoughts would be appreciated

I've got a good ole Bobcat 773 I mow with, I know tracs are better than wheels but finding it hard to justify swapping out the old girl for a new one. The area I mow isn't wet. I don't typically have a traction problem or a tire damage problem. I would like what I perceived to be a smother ride...

Hi! I have a Bcs 740 walk behind tractor with a berta 2 stage 85 cm snowblower. The Bcs is spinning a lot on snow with the heavy blower, so I have bought studded snowchains to improve traction. The chains should fit the small 5" x 10" wheels according to the seller. The included documentation...

Our landscape rake has two guage wheels running Carlisle 11x4.00-5 tubeless tires on steel rims @ 45 psi. It's time for new tires - the old ones are too weather cracked to continue - and I realized I haven't the slightest idea of how much force it takes to mount these type tires. I've never...

Has anyone reversed the rear wheels on the emax 20 for more width ? If so did it make a difference, and is it recommended ? Thanks in advance.

It was fun to do this project. Comment if you have any better way to do. Thanks Jkk

Looking for

I looking to get new tires for my yanmar ym169(d). My tires have dry rotted and can’t be fixed. The wheels on it don’t match the specs set out in the Manuel. The spec are below But what I have is different. Should I get replacement tires and not worry about finding new wheel and tires? Any...

That is the conundrum - tractor + wheels is 6" wider than the width of the rails on my trailer. I had the wheels measured to see if we can flip them around and by the time we do that it only looks like we'll gain an inch or so - not enough. So the next option is to take the wheels off. The...

Has anyone found wheels with actual bearings to replace the scalp wheels on a 5 ft mowing deck?

I have been struggling trying to level my driveway for years. Bought a land plane but it would not not take out the hills and valleys. My little back blade and York rake were useless…or at least I could not get them to work. My buddy and I went to an auction and there was an old 96” Woods...

Pair of rear wheels and tires off of my Kubota B20. They are filled with ballast. $100 for the pair Located Stow, MA. Cash Only

The wheels on my Log splitter are very cracked and I found a new pair of wheels very cheap ($20 for the pair) at Mardens (if you're from Maine, you know about Mardens). Problem is the splitter axle is 3/4" and the wheels are 1". Is there any reason not to get a steel bushing to make them work...

I thought someone may have spent the $$ for a set of the latest greatest fad TWEELS 🤠 Mike text or call six78 98six 322six

I have a 283 massey. Was shredding all going great. Stopped put tractor in neutral. Left pto running. Got on tractor to go again and it wont move. Good pressure on foot. Feels as if it went into gear. Any ideas

On the Farmall Super A, is the heaviest wheel supposed to be on the driver's side? Mine is on side of the motor.

I am looking to buy some 6.5x80-12 wheels for my BCS 740. The official wheels are sadly quite expensive. I find the wheels used on Blitz tractors to look very similar on pictures. Is there anybody that could confirm if these wheels would fit a BCS tractor?

Does anybody know how much a complete set of 19.5-24 & 12.5/80-18 New R4 tires & wheels would cost from JD ?

Had a disagreement with a tall stump hidden by even taller grass ... and an added excuse of dusk lighting... the tractor is a MF2660HD low profile made in 2010 and sold new in early 2011. Neither the thick parts book nor the owner's manual show this style wheel at all so I do not have an...