throttle

I have a new OEM carb on here and all linkages are setup correctly. Assuming I may have a governor issue but figured I'd ask to see if anyone has thoughts on why this engine (only 350 hours) wants to surge at high throttle? Thank you, Jay

I have a 1962 Ford 851. The throttle lever usually works as expected. That is, idle around 700, then pulling the lever down, throttle speed increases smoothly until it tops out around 2000-2200, and the governor will pull it back down if you go higher than that. So, occasionally, it will start...

My RK24 has started bogging down and almost dying at full throttle, any advice.

315 hours on my 3620H ROPS today and I noticed during the day a reduction in hand throttle lever friction then at some point it went completely away and there was about a 40% piece of plastic washer on the floorboard just under the throttle lever which I'm assuming is the friction disk. I...

I recently split my 1715 to install a new clutch. After putting it back together, I now have an issue with the throttle cables. When I hit the foot throttle it pops the hand throttle cable out of its seat. The hand throttle doesn't pop the foot throttle out. Should there not be a spring...

Hi all, lost throttle control on my 2011 BobCat CT-450 tractor. I think it’s a linkage connection in the steering column. Anyone have pictures inside or basic description of how to get in there? Thanks

changed fuel filter and replaced engine control relay. started up just fine but won't throttle past 2000 rpm. what did I do wrong? GC1723E tractor

The tractor has about 375 hours on it and never had a problem till this. It will throttle up, so I don't think it's the cable, but won't idle down past about 2000 rpm. No regen icon flashing. What do you suppose is up with that ?

Hey there folks, It's been a while and this old L245 has been running very well,, until recently.. and it may be something I messed up... grrr. So it a few weeks back I was running the brush cutter (not a Bush Hog Brand) and doing some general work with the front end loader. Had been going at...

Had the engine control relay go out in my tractor. Installed new one and now the tractor wont rev past 2000rpm. No issues with the cable. The throttle linkage has full range of movement. Not sure what would cause this. Any ideas?? Massey 1723E

Hi, new member and owner of a Boomer 8N, I am looking if someone could post a picture of their routing of the throttle cable under the throttle pedal. When I bought mine I found the cable end was broken. There is no illustration in the maintenance manual showing routing, the parts catalog...

It's really cold here in Indiana. I scraped snow off the driveway yesterday. Everything was fine. Then some one was stuck last night on the hill. So I brought a load of gravel there. I turned it off. When I restarted it the fuel was on really high, past 540. When I turned the fuel throttle...

I have a 2001 TC33D that I'm having some problems with. The throttle lever is very loose. I feel almost no resistance when I move the lever. When I started the tractor, the engine raced up to about 2200-2300 RPMs. I immediately shut it down. It feels as though the throttle is stuck mostly open...

i have a problem with my LS3032 throttle doesn't respond and tractor is stuck running right up to max RPM it still runs fine it is just wide open. the key switch will not turn it off, i have to block off turbo intake or un plug 2 wire connector at fuel pump. anyone have any ideas? thanks in...

The throttle on my TC45D won't stay in place. I add RPM and it just goes back to idle. How do I adjust this tension. I stretched the spring return a little and it helped for about a minute. Thanks!

Last winter I asked about the loose throttle on my Bolens G174 installed on a generator in my garage, tight to the wall. Once I understood the situation I leaned over the mechanism and drizzled a quantity of white Thread-Lok down onto the friction mechanism. The messy repair has worked very...

2017 2555 hst about 600 hrs. Had it about 4 yrs. In that time this happened a couple times, but this weekend it happened multiple times. After running the tractor for a couple hours fine, if i throttle down, then throttle back up, it wouldnt go above 1500 rpms. Let it cool a few hours it would...

Ford New Holland TL 100A under heavy load started over reving. Did not respond to throttle lever or stop switch. Throttle linkage seems good. Had to stop air supply to stop engine. Is this an injector pump fault.

Hello, I have owned this LS XU5055 for ten years now and have had this same problem since it was new. After a few minutes of using the brush mower on the tractor the throttle returns to an idle and the hand throttle becomes unusable. I can continue using the foot throttle but it only lasts a few...

I had to disconnect my throttle linkage mechanism bracket with the 2 bolts and carefully move it out of the way to take off the fuel shutoff solenoid. Nothing fell off that I was aware of in the process. When I was putting it back on and checking things with the engine off, it seemed like the...

4110 minhindra . Tractor ran out of fuel .when it cranked it goes to wide open. Only way to cut off is choke it down. 2003 tractor

All, I looked around to finger out how to change the boots on these (TN 55, 60, 65, 70, 75 cab models). All I learned is that others asked similar questions as well as a locking pin problem (locks the joy stick motion -- sliding collar on the joystick) but didn't list what they did or how they...

The throttle has been getting stuck at idle. Not sure exactly how the governor functions in relation to the linkage but for a while I couldn’t throttle up from the handle but if you moved the linkage at the injection pump it would be fine for a few days and then it would get stuck again. The...

I'm building a new log splitter that will have a Honda GX630 v-twin engine and I'm wondering if there is such a thing as a load sensing or auto-throttle for something like that? I got the idea from watching the Eastonmade channel and their newest Axis (SHO) splitter seems to have that. When...

I recently acquired a 5105. The hand throttle is super stiff. My Branson's hand throttle has a tension adjustment under the instrument panel. Does the 5105 have something similar? Is it easy to get to?

Hi all, My 2013 Workmaster 35 is having running issues. It will start and idle, but if I throttle up, it struggles. I've checked the fuel line to the tank for problems (none), and replaced the fuel filter, but it still has problems. However, when I tried to bleed the fuel filter via the...

Hello, I am having a throttle problem with my Belarus 250AS. The hand and foot throttle controls do not change the engine RPM. The tractor will start, but it's a 'runaway'. I have to kill it by placing something over the intake and it will slowly starve the engine of air and it will then shut...

Good evening, I finally got around to pullin my pump and watched several YouTube tutorial's on how to do it. This is on a 3 cyl perkins The good news is the leak seems to be fixed and it started! Bad news is it goes full rpm after it starts and I have to kill it by pulling fuel stop. I am...

Driving me crazy! Warning triangle on dash display with ! keeps showing up without really pulling it down...up a hill or any change in the load. Manual gives same good old response-call your dealer. Warning for all: I bought this new from a major dealer in another state and my local dealer...

Howdy I have a 3550 and the throttle slowly lets off while driving so have to continuously give more throttle then lets off slowly or have to hold the lever to correct speed. Any idea where to start to correct this thanks

I have a L S XU 6168 its a 2019 with 230 hours it has two codes F11 F31 i put two new fuel filters on it still has the codes no throttle lever or pedal however it run great it will move you just cant give it throttle PS were can i get a code reader for this tractor Any help would be...

Hello, I've stripped down my Iseki TX2140 about a week ago to change the clutch. Mostly all back together, however I'm clearly going senile as I can't remember what linkage goes where on the throttle, doh. I was unable to get the whole rods and levers as one photo as the FEL bits are in the...

My throttle is not staying put. It sure seems as if it is snug/tight, but it slowly revs down, and won't stay where I put it. I actually have a NOS fiber friction washer that my father in law gave me when he gave us the tractor. Is there any more to installing this other than removing the...

I have a 2009 GC 2400 which has been a workhorse since I got it new. 875 hours and going strong although yesterday I noticed that when I pulled the throttle back to idle, the tach and engine did not fully adjust. I checked the cable and connections and everything is fine. The lever does stay...