mahindra 3510

I have a Mahindra 3510 3cyl, 34hp. After setting for a month we started it and it smokes out the exhaust and makes a loud popping noise near the back of the engine on the right side. It does quit smoking for a while the starts smoking again. Drained fuel and add 5 gal new with a fuel additive...

I'm new to Mahindra. Just purchased a 3510 with FEL serial # Y03 so I guess it's either 2005 or 2006. When I got it home PTO worked fine. I removed the FEL for easier access and replaced all the fluids, front end, engine oil and hydralic oil. After all the fluids were replaced with the FEL...

Inherited my Dad's 3510 had it serviced. Should've asked them if it is full time 4x4 and what the shift patterns are on the two shifters. It seems to not pull with the front axle.

Today working on fall maintenance around our front pond. Got too close to the edge while backing up and got the two right wheels in the quagmire. I tried using the bucket as a flipper to get out, has worked on wet hills before. Kept getting in deeper. Was about to the hub on the front. Decided...

The vid is sped up 240x. Have not diagnosed it yet. My bet is a weak cylinder as it gets low and the sag slows down. No external leaks the machine is 21 years old. My next step is to diagnostically switch the hoses on the control valve to test whether it is the valve or a cylinder.

My 3510 has been an excellent machine for many years with very few problems but this week while bush hogging in very hot weather (South east Texas) the temp gauge was reading high and then went to nothing. The fuel gauge has not worked properly for some time. I'm thinking it is probably a ground...

Had to jump the tractor off several times. Then it would not take a jump and just clicked. Replaced the battery and still nothing. Replaced the starter and now it tries to turn over but doesn’t seem to have enough juice to turn over. Tried to jump it and still not enough juice. Thoughts?

I have been having intermittent problems with the engine dying and not restarting. My tractor is a 2002. I had previously replaced fuel lines which helped but not solved the issue. Looking at the right side you see the round booster pump from the tank, near the bottom of the picture. The...

Some time ago I read about potential fixes for 3510s running hot. Mine does too. I keep the radiator clean and full. I've not, but plan to, removed the side panels to see if doing so will help. One potential fix that seems to hold promise is moving the battery as it sits directly in front of...

While mowing, the oil pressure light lit. As I checked the oil level, I noticed the oil filler tube was missing. Is that a common problem? Thought about putting an expansion plug in the opening. Any issues with doing so?

I have an older 3510 HST, around 2004 era. It has quite a few issues, but the pedals recently stopped working completely (they had been stiff and messed up for a while, wasn't sure what was wrong). Turns out the part Mahindra refers to as LH Elbow had busted underneath it. It links the rod from...

Just after not finding anything in the used market for a decent price, I bought new 2022 Kioti ck2610 HST in July of 2022. I paid $20,358 before tax with a rubber mat, cruise control, and linked pedal kit. It currently has 13 hrs on it. I've also had the rear tires filled with rim guard. So far...

Hello, First time posting on here, my Mahindra 3510, I'm guessing 2001ish model is experiencing loader lift and rear lift issues. If you give it lots of throttle it will work very slowly on both ends. Fluid looks good and clean, I have read something about pto lift needing to be in neutral? Not...

Does the PTO just spin in one direction. Is there not a forward and reverse? Example: on a digger attachment can the blade spin forward and then in reverse to remove the bit from the hole and spin the dirt off of the bit?

I have inherited a Mahindra 3510 and have little to no knowledge about this tractor. The items that I need help on are the following: 1. How to check the fluid levels for oil, hydraulic and transmission? 2, How to engage the PTO? I have a digger attachment, but cant get the PTO to engage. I...

I have a 2005 Mahindra 3510 (New Sheet Metal) and I can't find the Relay for the Solenoid (1 Wire). I don't have power coming to the Solenoid! I've physically looked and researched but don't see anything showing Relay location nor is there a Fuse concerning the Solenoid.

I have a 2005 TYM HST330 which has mostly served me well. Made by TYM, it was also sold as the Mahindra 3510 (so you Mahindra owners might have a suggestion here). I bought it used in 2010 with 191 hours on it and recently passed 700. It has an SCV (secondary control valve) and its control...

Im about to put my 2003 Mahindra 3510 on the market, , 4x4, aftermarket loader, ag tires 2 years old, 1264 hrs, everything works as it should except the fuel gauge,,tractor looks and operates very good, shed kept,, what would be a good price range to ask,,any info appreciated,,looked on the...

Mixed comments on this.Is there already a threaded opening to install a threaded block heater on this engine. The tractor is a 2006 with the 3 cylinder Daedong Diesel.I am not interested in using an inline hose heater.I can install the Kubota bushing in one of the freeze plugs that provides a...

Hi the glow plugs went bad on my 3510 and I've been looking on the internet to buy new ones but there's a ton different options and a huge range of prices, does anyone know what plugs will actually fit? Thanks,

I have a 2007 Mahindra 3510 that I bought with a backhoe and have never taken it off. I want to buy a Countyline rotary cutter to clear a few acres of brush. Moving the position lever from 1 to 6 doesn't move the 3 point arms, and I have the turn knob under the seat in different positions and...

I bought this tractor used, 226 hours, everything works just fine except the warning lights quit. Al lights, turn signals, horn, tachometer, fuel gauge, and temp gauge all work. The PTO and Cruise buttons and lights both seem to work as well. Actually only two things I can find that do not...

HELLO, as the title states, can't track down where one of the 2 wires connect.... no sign of the other wire. I had a branch take out the plug connector years ,ago, and had them hard wired in without plug... please help, thanks in advance.

I have so many issues I don't know where to start so I'll start with the oldest problem. About 10 months ago the 3 point hitch became stuck in the up position and I've tried most of the easy remedies suggested on this board but nothing has worked. Next event was my inability to crank the...

Tried to engage the pto but it does nothing. the lever is up in the 540 position and the selector switch in the manual position ant the switch is pushed in and light up.

I am new here and new to working on hydraulics. with that said I own a 2008 Mahindra 3510 4wd gear, I just bought a new root rake with a clamshell. I had to change the detent valve out to add in an extra set of lines to operate the clamp. I did some research and found that the one that came with...

A user on another forum is considering purchasing a used 2007 Mahindra 3510 with 700 hours, along with its 3 pt backhoe. What should he be looking at to assure that the 3 pt backhoe has not damaged the tractor? I know Mahindra warranty does not cover damage from use of a 3 pt backhoe. Warranty...

Im at my wits end. Anyone know where to locate the starter relay on my 3510. I have an intermediate problem where a get just a clicking when I turn the key. After 20 or so tries it starts, then seems to work the rest of the day. I've cleaned and checked the starter solenoid, but I can't locate...

Hello to all! I am a new owner of a used 2006 Mahindra 3510 Shuttle Shift tractor. I did receive the owner/operator manual with the purchase but was disappointed at the vague info therein. My tractor has certain issues here and there. I want to attempt self repair if possible. Does anyone out...

Last winter (very cold in the Northeast) I wasn't able to start the tractor. As the weather has become warmer, the tractor will start without a problem but if I run it for more than a couple of minutes it starts to lose power, it surges, and eventually stalls out. I've noticed that if I bleed it...

I have a 2006 3510 4x4, it has 276 hours on it...The tractor will not shut off when I turn the key to the off position, it acts like its is wanting to but never does. I have to "pop" the clutch to shut down. Where do I need to start?? Thanks

My Mahindra 2002 3510 sprung a leak of on one of the short coupling lines that hooks to the the transmission oil filter down on the right side of the tractor. It had the wire type of clamps on it so I replaced them with regular hose clamps and it seems to have stopped. I want to replace the...

I have a 2006 Mahindra 3510 that is leaking 80w-90 out of the bottom of the steering joint on the right side of the tractor. It is coming from the very bottom of the joint below where you drain the front axle, anyone had this happen or know how big of a fix this is?

I just purchased my 2006 shuttle shift Mahindra 3510 and am in need of a owners manual in either pdf or paper back. Thanks in advance, love my tractor, great site. Thanks again!

Hello all, I'm a relative newcomer to the tractor world but already need help. All I did was to hit a stump! The filter snapped off the part of the base that screws it screws into, and the inlet pipe attachment to the filter also broke. I'm having difficulty obtaining the part numbers and a...

Hello all, I'm a relative newcomer to the tractor world but already need help. All I did was to hit a stump! The filter snapped off the part of the base that screws it screws into, and the inlet pipe attachment to the filter also broke. I'm having difficulty obtaining the part numbers and a...

time to get the little feller ready for summer work... the original battery appears to be shot, what is a good replacement that won't break the budget? I bought a new battery for my cub tank last fall and I thought it was terrible how much they'd increased in price since the last one. I can't...

looking for the proper way to replace ignition switch on model 3510

this forum has been really great help to me with my tractors and mowers... i hope this problem can be resolved. an issue that has bugged me about this little tractor since i bought it... it just seems to me that it runs too DARNED hot! i keep the radiator clean, inside and out and don't run it...

I have a mahindra 3510 and at first I had to change out my 8 year old battery, WOW!, now it will not shut off with the switch. I have to pull the cut off handle. It runs good and starts good. I checked for power to my shutoff solenoid and I have NO power with the switch on or off. Is there a...

Does anyone else have a PTO log splitter on their Mahindra? As you know the Mahindra has a rear hydraulic port. I read about open and closed systems and that the device need be matched to the machine. I am unsure. I got my Mahindra from a used equipment dealer 150 miles away. Hauling the tractor...

I have a 2005 mahindra 3510. we have had an issue starting. We would have to pump the clutch several times while holding the key to get it to crank. My worker was using it yesterday and it cranked fine. tried to use it a few hours later and cannot crank it. We have also had issues of...

Looking at a Mahindra 3510 Tractor with QT Loader

thank you for taking time to read this, i appreciate your interest. how does the 3510 with a FEL do as a snow scraper? i am having the farm lane paved and part of it is a pretty good grade. i am debating on one of the push type snow blowers, putting a grader blade on my cub cadet tractor...

Mahindra 3510 gear oil I am looking to change the fluid out in the rear differential. I think the hydraulics are shared so I am curious what grease to use. I just changed the front out and used some 80/90. Will this work in the back also and how much. Thanks....

The beast is due for a 500 HR Tune Up. My son was home for the weekend and went down to the lake house where yhe beast lives to get his fishing tackle. While down there he was cranking everything and the battery was dead on the Mahindra. (original battery new in 2003!!). I now will be installing...

Can any one tell me how to replace the cap on the bottom of the final drive assembly? Can it be remove without taking the entire assembly apart?

Newby here to this forum I was grading a home pad today and a tree root went up into my fan shroud and SHREDDED my fan. :mad: Again, tractor is a Mahindra 3510. Where can I get another fan and are they expensive? Thanks Tommy

When I turn the key to start my 3510 it just clicks one time like the battery is dead. Then when I turn the key to off a buzzer goes off even after I remove the key. I have replaced the battery and the starter switch but it does the same thing. Can anyone help?

Where is a good explination of the PTO engagement problem? Does anyone have any picks of the PTO engagement solinoid?

I'm in the market for a smallish (< 50hp) tractor to work 10 acres of land in east Texas. Primarily bush hogging, driveway maintenance, landscaping, occasionally moving some round bales for cows, etc. I found a Mahindra 3510 4WD with front loader for $10,000, 8 yrs old with 1,000 hrs...

I have a 2004 Mahindra 3510 4x4 with loader. When I start the tractor the loader and 3 point doesnt work. I let it run for about 5 min. When the temp gauge starts too register a temp I turn the tractor off and then back on. Then the loader and 3 point work from then on. So basically the...

Well, been shopping for a couple weeks and stumbled on a 2004 Mahindra 3510, 362 hours, ML112 Loader, 1 set rear hydrolics, canopy and a 5' Dale Phillips cutter for $8400. You can see what I want it for here...

Had a broken line -repaired it added new fluid Ihave nothing, pto wont engage bushhog,front loader bucket will not move. I have little knowledge of tractor just got it used. I need help to trouble shoot this.

Had a broken line -repaired it added new fluid Ihave nothing, pto wont engage bushhog,front loader bucket will not move. I have little knowledge of tractor just got it used. I need help to trouble shoot this.

Mahindra 3510 lost all fluid broken line refilled after repair- loader bucket does not work-- cant raise bushhog. I could use some help i have no manual. No response , should this new fluid be bled? Where should this be done at?

Has anyone ever taken any steps to increase the lifting power of the FEL on a Mahindra 3510? If so, what did you do and what did it cost? I've been trying to use it to move pallets lately and I simply need more lifting power to get the job done. Thanks. Rusty

I have a gear drive 3510 and am looking at getting a new finish mower. I have my eye on a kingkutter rsfm-84. I really like the idea of the mower sticking outside the rear tires on the tractor but I might be biting off more then I can chew. I have a 6 ft bush hog that never bogs so I have other...

I have been reading all the posts since I ran across this site. I am at wits ends with my overheating problem. Seems like I can't seem to clean the radiator and screen enough to keep from overheating. It is no fun knowing I can't work for an extended period of time. Any help is appreciated...

Does anyone have the PECS installed on a 3510? After doing a little research I discovered one of the requirements is 4" of straight lift arm. I measured mine and I have 3-3/4" of straight lift arm and was wondering if it would still work. Thanks, Joe

I own a '04 Mahindra 3510 with approximately 650 hours on it that has worked flawlessly in every way until today. :D I ran it this morning for about 30 minutes backfilling a hole and shut it off at the work site while I went to gather up some tools. When I went back to start the tractor to...

-------------------------DK35----------3510 Lift capacity-------------2,425----------2,865 FEL lift------------------1,350----------1,972 FEL breakout------------2,100----------3,343 BH bucket force---------2,675----------5,676 "best" model BH bucket force------------------------2,000 "worse"...

I'm looking at the Mahindra 3510 (used) and wondering if any users have had any problems. Do things hold up after 400or500 hrs? Would you buy another and that type thing? Any regrets? Thanks I'm still getting educated on tractors.

my mahindra is giving me problems going into gear. at times i can only get it into low third. any advice/comments would be appreciated

mahindra-ML-714001-ML-

my 3510 will not always go into reverse, it seem like it is not fully engaged and pops out of gear. is there a linkage adjustment? <font color="yellow"> </font>

is the daedong diesel in the 3510 the same as the cubcadets are using? guess i got into a hurry on this one... thought i'd done my homework and that mitsubishi was the manufacturer... but, when i set down and finallly looked at the user manual, i find the daedong company made this motor... i'm...

words cannot express the performance of this little tractor.... i won't say what other tractors i have, but this little feller is the alpha-tractor here...

Okay everyone! Here is my narrowed done list: Branson 3510 Sync, Mahindra 3510 Sync and Kubota L3400DT. Let the opinions and expertises fly and don't hold back!! Thanx in advance, Bob

I think Willman asked this same question, but no responses, so here it goes again. The brochure for the 10 series mentions auxillary 12volt connector. I assume it is the connector in the rear that looks like a trailer connector. WHERE do you get a connector to fit that thing?? I guess you...

It got here late today so I only got to move 2 buckets of gravel in the dark. Defenatly am NOT going to wait to fill the rears. I could feel it with with a full bucket. Since I already have 50 gal of WW fluid sitting in the garage Thats not a biggie. Project for tommorow night. If my pump rig...

All you guys (and gals) are great! I've been walking through the history of some of these chats and I've learned a ton. That piece on HST was awesome...needed a PhD to understand some spots though. Anyway. I was not able to find much on Mahindra. I know the history of the company, and I...

mahindra-ML-216347-ML- Moved to Mahindra Forum.

OK, I had my first serious talk with a dealer today. I was quoted $15,550 for a new 3510 with Mahindra loader. Unfortunately, I forgot to get the loader model number, assuming Mahindra has more than one FEL that fits the 3510. Any comments on the price? SnowRidge