john deere 4110

2005 JD 4110, 340 hours, hydrostatic, 200CX FEL, Frontier pallet forks, 60D MMM, always garaged, original turf tires, folding ROPS, located south of Houston TX. I don't want to give it away, but I don't want to wait it out for "top dollar". Suggested price?

Operating manual showed a different number than the internet. Called dealer and parts person said the manual part number was outdated. Replaced fan belt with #M800347 from the dealer which matched the internet information. Tried to install it and it was too wide and tight. Won’t tell you how...

Purchased this little 20 HP YANMAR mule at auction with 694 hours. Even the engine paint looks new. After servicing and changing filters I mowed some very tall spring grass and compared to our X734 with a 25 HP Kawasaki there is no comparison to its ability to mow with diesel “torque”. No leaks...

i have a john deere lv4110. serial number lv4110g112091. its not charging the battery. just had the alternator rebuilt. its the 55amp alternator not the skinny smaller alternator. the battery light is not coming on, bulb is good. iv swapped relays and made sure all fuses are good. im down to it...

I've had my Deere 4110 for 14 years now and it has always served well. But it's getting a few too many hours on it now (1620) and I'm looking to get into something with a little more hp and a lot less hours. I though I had a 3032R lined up had a quote for mine and was ready to finalize the...

there is an adjusting screw under a castle nut next to the fuel pump solenoid on my jd4110 any one know what it is for?

Good Afternoon Can anyone please tell me where the parking brake switch is located on a John Deere 4110? Either I need a new switch or an adjustment on the parking brake. The parking light on the dash continues to blink after I release the parking brake. Thanks, Eric Louisa, Virginia

Hey all, I was wondering if a Grille off a John Deere 4210 would fit the 4110? They look the same but wasn’t sure if anyone else has tested it.

I own a 4110 compact. FYI I'm not a mechanic but I can get by with some simple fixes. For yrs it's been really easy attaching my bushhog or the yorkrake to the tractor until we had transmission issues last year and had my tractor guy rebuild the back end. For some odd reason it's almost...

I hooked up the mower today to find I could not move the PTO from rear to mid. It's stuck. Here is what I tried. 1. Turn PTO on and off 100 x's. Just kidding but did it a lot. 2. Push on lever while PTO is started and stopped. Just before it comes to a stop 3. clean and w-d40 all linkage 4. I...

I am looking at a John Deere 4110. I'd like to make sure that this is a capable enough tractor for me. I need to be able to care for my gravel drive and help me with firewood and other property tasks for my 7 acres. Does this fit with the current 4 series tractors?

Hi. I have a JD model 4110 that I bought used a few years ago. I have always thought something wasn’t right with the underbelly lift attachment. When the 3 point lift is in the down position, the metal arms pretty much drag on the ground. When 3 point is up, they are up and out of the way. I...

Would it be possible to bypass the entire safety switch circuit, by running a jumper from the BR2 terminal on the key switch to the 1 terminal on the k1 start relay instead of having the wire from the G terminal on the A1 control module connecting there? Would this damage anything? Would I...

I have a 4110 Deere that has been stating great and running great. Last time I ran it was about a month ago. Never have had any issues with it starting. I went to use the tractor the other day and the battery was dead. Tractor would only click when trying to start. I jumped it with my booster...

Just got in a JD 4110. Needs complete fluid and filter changes. I didnt get a manual. So looking for recommended fluids and capacities. And if anyone has a list of filters and cross Brand filters that would be great. Planning on doing motor oil - trans/hydraulic fluid ( and clean suction screen...

I have never had a drop of oil leak on anything under my John Deere 4110 compact tractor. Went out this morning and had a puddle of oil inside of each front tire where it had been running down. Any ideas what could cause this to happen so fast and how to replace the seals and whatever else needs...

So I have been hunting for a subcompact for about a year now. I was at an auction yesterday and purchased a JD 4110 with 404 hours on it. It has a loader, good rubber, no damage, 4wd, mid and rear PTO. Everything works except the PTO lever is stuck (which I hear is a common issue when not used)...

So I have been hunting for a subcompact for about a year now. I was at an auction yesterday and purchased a JD 4110 with 404 hours on it. It has a loader, good rubber, no damage, 4wd, mid and rear PTO. Everything works except the PTO lever is stuck (which I hear is a common issue when not used)...

Hi. I have a JD 4110 hydro tractor that recently developed an issue with some type of switch or interlock. Tractor starts and runs fine with gear/range selector in neutral, but as soon as I move the lever to either H or L, the tractor shuts down. Can someone tell me what component is causing...

The 4110 has served me well and I love it, but I've outgrown its usefulness now that I've started expanding the pastures. Just wondering what everyone's experience has been with Mahindras, especially this model. I've really become dissatisfied with JD quality and the ridiculous pricing as of...

I was wondering if anyone has corrected the situation where the alternator light does not come on when the ignition key is in the "On" position? The other lights that should light are working fine. The tractor is running fine at this point. I have checked the light bulb, fuses and the wiring...

My tractor's loader joystick seems to be binding during the curl action... It seems ok for raising/lowering. It worked ok earlier this year, but I didn't use the tractor for a few months and now it seems messed up. Any ideas? Thanks much.

I have a JD 4110H (Hydrostatic) and had a Oil Tube line crack this weekend. The clear fluid is coming from the a cracked Oil Tube line, part# LVA800157. The loss of the fluid has made the steering wheel free spin with no steering action. Is this normal if all the fluid runs out? If I replace...

I have about 2.5 acres of lawn that I mow and currently own a Husky zero turn. The ZT does a good job but I'd like to consolidate being I have the Husky and the JD4110 and a Kubota L2700. Currently have a 60" LandPride finish mower on the JD works okay but I'm thinking of getting a mid mount...

I own a John deere 4110compact tractor2003 reg. There. I a leak of hydraulic fluid between solenoid and p.t.o. Clutch/brake do I need to split the engine/transmition HELP,

Hi fellas, the lower bearing and seal went out on my mower deck gear box. After tearing it all apart and finding blue gears and wasted bearings I find out Deere doesn't break it down into parts but wants to sell the whole gear box for $653.xx. Any one know where or how to find new gears for it...

I somehow stumbled onto a couple good ones the other day?? I need to do mine.

1400 hrs. been great! I took front wheels off for new tires but dealer got wrong size so I put them back on, next morning I see a puddle on each side & find lower seals on knuckle leaking alot...wtf? #22 in pic

I've been wanting to buy my first tractor and have been looking for used Deere 4110s with the 410 loader. Most that I've seen have between 400 and 600 hours. Being new to tractors, I don't really understand if that is a decent amount of hours (how long do these machines typically run?). Also...

Have anybody replaced a voltage regulator in this tractor? Any comment will be appreciated.

I have an 04 4110 and the fuel shut off solenoid went bad and blew the 40a fuse. i replaced the fuse and plugged in the new solenoid without bolting it in to make sure it was going to work. when the key is turned it pulls in like it should but after a minute or two the thing is so hot you can...

I have checked the alternator and it has a good battery. Replaced the voltage regulator and start switch (ignition/key switch). Symptoms - no light for battery when key switch is in Run Battery runs down when tractor is used but starts with no problem. I have replaced the bulb for the...

my 2005 john deere tractor started to discarge all of a sudden and i can't get a john deere dealer to test the alternator with out bringing the whole tractor. can anyone direct me ? thanks

I have one and need parts for the front right final drive, or would like to buy used assembly. Any info would be greatly appreciated. Thanks

Not charging newer diehard, disaasembled alt & cleaned, still dies when + cable is disconnected from batt...not much to alternator, just a magnet & stator..?? maybe theres a bad regulator somewhere? Thanks for any help!!

Not charging:( newer diehard, disaasembled alt & cleaned, still dies when + cable is disconnected from batt...not much to alternator, just a magnet & stator..?? maybe theres a bad regulator somewhere? Thanks for any help!!:)

Looking to trade the 4110 with FEL, Box blade, and BH RDTH 60in finish mower. I am wanting to stay with JD, but what compares to the 4110? I will be wanting the same attachments, but a MMM instead of a drag behind finigh mower. Thanks

Hello everyone I am looking to buy a used J.D.4110 was looking for anyone's opinions on this tractor good or bad it has low hrs with loader and mid mount mower and immaculate condition Thanks

Another go around with the hydraulic oil and filter. @ Near twenty dollars a gallon I hope there is magic in the Hy - Gard transmission oil. I guess if it moves things correctly it is a must. The trouble is justifying a $35.25 filter Kind of grinds on my assumption of '' being held up...

sorry ignore this i already asked this question but couldent find it of corse now i have ? :) Chuck

Getting old I guess, but has anyone swapped out the seat on their 4110 for something more comfortable?

hi all would I have a chance to buy a tractor ....I think the size of the tractor is ok but just not sure if its a good deal so any help would be appreciated so here we go the tractor is a 2003 john deere 4110, has a 410 loader, still green inside the bucket, with 125 hours, got the r4 tires on...

Hi all, I am considering purchasing a 2005 John Deere 4110 tractor with bucket, ballast box, mower deck, box blade and land pride LR1560 rake. 445hours. R3 tires (likely going to need to switch these out). Tractor looks to be in very good condition, implements in acceptable condition. Asking...

Have a 9 year old John Deere 4110 and have had no problems with it at all. 6 months ago it started to blow a fuse everytime the lights were turned on but everything else was fine. Recently I ran it for 45 minutes or so and shut it down. Tried to re-start it and not even a click. Battery is...

I am looking for the power beyond block for a John Deere 4110. New or used.

I figure I should get a 48 in tiller. Is that correct. What kinds are good and heavy duty? Any other advice is appreciated. Gary

My 4110's 3-pt hitch lever is acting up. It had been binding, but with some effort, I could always get it to move the full range. Today, I looked at the level and it was a bit twisted. I straightened it, (aka bent it back) but now it moves to the highest position ok but will not go lower than...

Been a while since I have posted, tractor is at 650 hours and I need a new seat. I went by the dealer today and they want 370+ for a new seat. Has anybody else replaced theirs or tried any on Ebay? Thanks Jeff

I have 2 questions: John Deere 4110 power steering cylinder P# AM879356 Does anyone know if there is an aftermarket cylinder to replace this? I've only seen new OEM ones @ $600.00 give or take. Ford 8N I'm looking to get a new Marvel updraft carb for it. Where is the best place to get one and...

I have a john deere compact 4110. will not start. I jumped the starter to get it to my garage. I had the starter checked OK . I then replaced the glow relay. checked the fuse. Was this relay the right relay? Is there another relay? What am I missing. battery is fine

I have a Wallenstein backhoe GX 600 on a John Deere 4310 subframe! Can it be attached to a John Deere 4110? Any helpful advise would be appreciated. Thanks.

this is my first post, and its not a happy one! i have trolled around this forum aplenty though! anyways, the tractor i picked up is a 2003 deere 4110 TLB (410 loader, 46 backhoe) has about 230 hours on it. the previous owner bought it new and used it to build his house, then when he got...

I recently purchased a used 47 snowblower for my 4110. It came with the pto shaft, blower head, and quick hitch. I bought a used carrier bearing housing, and new carrier bearings and holders. When I put the carrier bearing housing on the front of the tractor on the loader hood guard brackets...

Can you install the power beyond valve on a JD 4110 that does not have a factory loader valve? Or is there any other way to add a valve to my tractor. The factory valve setup is cost prohibitive. I have read many of the posts about installing the power beyond block and a valve but never found...

I have an '03 JD 4110 hst and it recently developed a hydraulic leak. First of all, I'm very surprised as it's in an area (near the banjo fitting?) that is well protected, so I wouldn't think a leak would occur there. Secondly, it's not the banjo fitting itself, but the line that leads up to...

Good Morning All, My jd 4110 3 pt hitch won't drop, I checked the flow control and it opened all the way and they won't drop. I have not used the 3 pt since last fall when i raked my driveway. I did put the rake on hoping the weight would help lower it but nothing. So then I thought I would...

Hi, I just got a JD 4110, with 60in mmm, and 410 FEL. When I cut grass, the RH front caster wheel presses hard into the ground. When I back up, the caster wheel rotates about 90 deg, and cuts into the grass. We have had so much rain this month, the ground is saturated. When the deck is...

Need some immediate help. 4110 HST is sitting in the middle of my field. Using the loader all day to move mulch and running fine. Shut it down for a break. Would not crank and only a buzzing noise. Jump started and ran fine and used it for about an hour. Shut it down and had to jump start...

Started the tractor today and was letting it run to warm up. I got back on the seat and as soon as I sat down the machine shut down, black smoke came from the engine compartment and it smelled electrical. Background: About a year ago I was having problems with some acsessory work lights I...

If I can't sell my 4110 before the move, I will have to transport it approx 350 miles. It measures a hair over 20 ft with loader and finish mower. Has anyone tried moving a smaller tractor like this in a a u haul truck? I can get a 26 footer for approx 400 dollars one way and still have room for...

We are moving Florida to Georgia and new owners are asking for a price on my JD tractor. Here's what I have and the price paid (which I know means little): JD 4110 Hydrostatic Drive, 4WD 11,513 Bush Hog RDTH 60 finish mower 1,750 JD Front end Loader 410...

i have a john deere 4110 thats about 3 yrs old. its been working just fine until couple days ago it started to stall in high gear ( sometimes). if i switch it to low, it picks up a lil bit and carries on smoothly. but at times during an uphill it stalls in high gear and the engine totally shuts...

Well, after 9 months of tractor shopping and lots of test driving of new machines, I found my tractor (by pure chance) for sale on the side of the road last Sunday and picked it up on Friday. It's a '03 4110 with 800 hours. It came with a Curtis Cab, 60" MMM, FEL with 53" bucket, 46 backhoe, 54"...

Hello. I have a JD 4110 with a 410 FEL. The loader lifts fine and curls down fine. But it will only curl up about half-way and then stops. I haven't found any leaks/broken hoses. Any ideas? Could it be a cylinder? It was working fine one day and the next day didn't curl up all the way.

what is a jd 4110 worth with a 410 frontend loader 60 in belly mower? 290 hours hydrostatic and r4's please let me know quickly as i am looking at getting this week mint condition one owner tractor?

Hello, I hope I can get some assistance with my JD 4110. This is a 3 year old machine with 100 hrs. During operations the engine shut down. I suspect an electrical component however I don稚 have access to an electrical schematic. After the engine stopped I attempted a re-start. With the key in...

What would be the best way to transport a JD 4110 with RFM, bucket, and box blade? Total distance is approx 400 miles. All I have available is an Expedition and I don't think it would pull a tandem trailer with these implements. Would a U Haul enclosed truck work?

Had an incident I'll mention in the safety board but now have a tractor that will not start. Tractor rolled down hill, over some rough terrain, in neutral, and came to a stop with engine off, key I believe was still on - I was just glad operator OK. It did not go over any drops, just hilly...

So I'm really in the market for a tiller, I found a JD660 tiller, its 5ft. I know I should use a 4ft but if I took it easy would a 5ft work ok? My 4110 is 20hp. Thanks!! Brandon

How does the 410 loader on the 4110 compare in lift capacity and cycle time to a 200cx on a 2320 or 2520?

I want to start gathering materials for construction of a front end loader for a 4110 John Deere. I am thinking 2" x 3" by 1/4" steel tubing for the arms and 1/8" plate for the 54" bucket. 3/8" plate for reinforcing where the rams attach and 1- 1/4" pins. Will the 2x3 tubing be strong enough...

I currently have a Bush Hog rear finish mower and am thinking about going to a mid mount mower. I could then cut more grass around the house, where the rear mower's wheels gouge out the turf etc. I have a front loader that I leave on all the time. What will a mid mount do to the balance? I also...

Hi, Newbie here. I have a JD 4110HST and after the last snow I noticed I was leaking hydraulic fluid. After much searching, I discovered it was coming from a gasket under a plate on the side of the tranny. (left side as you are sitting on the tractor) I couldn't tighten the bolts, so I loosened...

Greetings from Brookings Oregon! I just joined this forum and this is my first post. Well, I just purchased my first tractor and hope I made a good choice - a 2005 John Deere 4110 with 46 BH and 410 FEL. It has about 450 hours and is in very good shape. I paid $13k - hopefully a good price...

I am looking for a tractor cab for my JD 4110!

I am looking for a tractor cab to fit my compact diesel John Deere 4110! I have checked with Curtis and Simms and they no longer offer them for that tractor model.

There's a John Deere dealer located nearby that has a used 4110 compact sitting on their lot. It has 274 hours and looks to be in good condition. It comes with a loader and a 60" mmm. I stopped by this morning and the dealer let me take it for a test drive. As I said, it looks almost new. The...

The tractor is great. The mower attachment sucks. Not only is it hard to get on / off it only raises about 3". When leaving it on for other tasks I have to be so careful not to drag the mower through a low spot. I was toying with the idea of mounting it ahead of the front wheels. Had I known...

Hi, I'm looking at a 2nd hand JD 4110 , gear drive, with 100 hrs on it. I was wondering what kind of experinece as far as durabliity goesthat people have had with it and is still made. Also was it made in Georga or Japan. I know it has a Yanmar engine. I will enventually put a hoe on the...

I'm considering a PTO driven chipper for my 4110. Chipper specs say it will take 4 1/2 diameter material, anything over a couple of inches is firewood in my book so I wouldn't be pushing the chipper to its max. My 4110 pulls a 48" tiller through 5-6 inches of virgin Vermont glacial leftovers...

I have a 2005 4110 with 34 hours on it and was wondering if anyone wanted to trade R4's for my Turf tires. Looks like I will need tires and wheels since the wheel size is different. John deere dealer says end of August....maybe?

First thing, this site is incredible and has been really helpful. I have a JD 770 with loader and mower and am looking at buying a tractor with hydro. The dealer has a JD 4110, loader(200x), mower(60"), ballast box, 1.5 hours(new) for $15,700. Is this a good price and what is a good trade in...

Anyone tried to put one of the universal replacement seats with suspension mechanism on a 4110? I had one on a little Case IH 234 that resulted in a much better ride. Here's a link to one of the seats at Northern Tool, although there are a number of suppliers of similar seats, including TSC...

I ran across a JD 4110 with a 78” loader mounted snowplow. Is this too much plow for this tractor?

I would appreciate any thoughts as to the advantages and disadvantages of these two machines in overall use. Aside from typical TLB tasks, please consider mowing, snow removal, posthole digging, grading, driveway maintenance, log hauling and anything else that comes to mind. Thanks.

I was thinking about the JD 2520 but my dealer has suggested a new 2005 4110, 4wd, hydro, dualSCV's $11,300 200CX loader $2,300 54"MMM $1535 46 Backhoe $5,400 Total Package $20,535 plus tax, delivered ready to work. How does this compare and do you think I have some negoiating room?

Any idea on a fair price for this tractor and attachments? 2003 JD 4110 HST 21hp 54 hours 410 loader and weight box 47" front mount snow blower 54" mid mount mower LX5 rotary cutter Also has R4 tires and ROPS Thanks Lisa

I added 2 rear remotes on my John Deere 4110 CUT, I used the Power Beyond kit from JD to access the hydraulics for the new valve. The valve I used is a Danfoss valve purchased from the SurplusCenter The first pic shows the mount I made and welded to ROPS x-bar. Rear View

Hey gang, I am finishing working up the final details with my dealer for the 4110. I want to have rear hydraulics and be able to control the rears while still using the bucket. My salesman hasn't sold a set up like this on the 4110 and he is checking to see what I need. Have any of you done...

I am looking at CUTs and am comparing the JD 4110 and a TC21DA that my local NH dealer has. I am eleigible for Ford employee pricing. Is the TC21DA still produced, or is this a leftover... I don't see the specs on the NH website... I will be mowing about 3 acres, brush hogging a couple...

60\" tiller JD 4110 Hi folks, I just did a search for tillers but didn't see anyone running a 60" behind a 4110. I'm thinking of buying a KK but wonder if I have enough tractor to handle it. Thanks for any comments.

Greetings, Our local dealer (PA) has quoted me $11,950 for a 4110. I can save $500 by deleting the hydraulics for the FEL but I think I'll keep them just in case. Also adding $995 for a LX 4 Rotary Cutter. I checked in at another dealer in MD and he was about $2,000 higher. Comparable set ups...

I am looking for the best power rake for the John Deere 4110 or 4115. There are not too many of these rakes in use in my area and I thought this might be a good fit. I want to keep the tractor size to a smaller compact. I have seen both the Harley rake and the Woods Power rake and both seem...

Hello to the most intellingent folks who know so much about tractors. I am amazed at all the help from you all!! Which brings me to my question(s)...I have been looking at a Mahindra,Kioti,and John Deere. JD is a 4110 hydro,Mahindra is a 2615 hydro,and Kioti os 25 hp,hydro. I have a 14 acre...

I went shopping with a buddy today...he likes the green tractors. I told him I would run the numbers by the wise folks on the TBN JD forum. JD 4110, 60" MMM, mounting hardware for the MMM, turf tires, hydraulic valve for the FEL (no FEL though)....$15,414. The salesman said this was a $2,400...

I was about to purchase the B 7510 and the JD dealer called. Here is the deal. B7510 with 302 FEL, 60in mmm and 48in box blade for 15422 including taxes at around 735 dollars. JD offered the 4110 with 410 loader 60in MMM and 48in box blade for 15650 before taxes 782.50=16432.50 For the one...

I've had my 4110 with the 410 FEL for about 2 years now. Starting to notice leakdown on the FEL. I can understand a little leakdown witht the enging off, but even when running it will drop about 2 inches in 10 minutes. I called the dealer and he said that was "normal". I've seen tractors at...

I got a price from a dealer for $16,200.00 for a JD 4110 w/ hst, FEL & ballast box. Thought it was a bit high. Dealer is close to home ( 8 miles ) so I want to do biz w/ them, but not if I'm giving away big bucks. ( I'm in upstate NY ). Also, what does a similiarly equip't Kubuta in the same...

Is there a supplier where you can buy an aftermarket 35 amp alternator for a John Deere 4110?

Folks , I am was interested in installing an oil Drain Valve and I can not seem to find out what size the drain plug thread size is for my JD4110. I called the dealer and they did not know (why am I not surprized) and tried Yanmar with no luck. I think it is either 22 or 18 MM , but I am not...

Hi All, We have appreciated the help along the way and now look to purchase one of the above units w/HSD. Our homesite is 2 1/2 acres of gently rolling/oak land in SoCal. I like both tractors; have concerns about ground clearance of the JD due to hydraulics being on underside -- dealer very...

Folks , I am at my 50 hr service and while I have the trans fluid drained I thought it would be a good idea to put in a Trans fluid heater. Just like the block heater I installed for the engine , however for the Transmission. After cleaning the suction screen I noticed two magnets in the...

Both are similar sizes, prices, and both hydrostatic. Both have loaders (JD 410 vs Kubota LA352) with similar capabilities. Both have backhoes (JD 46 vs Kubota B4672A) with similar capabilities. Drove the Kubota and liked it, but I didn't like the brake pedals so close to the forward pedal, on...

How to remove 60\" MMM on JD 4110 My 4110 was delivered this weekend and I was a little disappointed that the MMM could not be locked in the up position while I used my 3PH (my fault for not checking this further - thought it would be like the 2210). I did remove the MMM but it was difficult...

I just recieved a new JD 4110 with FEL 61"bucket, Ballast box, curtis soft cab, Heater, and am / fm stereo cassette, 5' back blade and 60" rear finish mower. I'm not sure what rpm to use for digging or moving dirt. And can you hurt a hydro transmission? Thanks!

trying to make the decision between both of these tractors. The kubota was quoted at $12400 with loader while the 4110 was quoted at 14300 with loader. Am i missing something. Whats the difference it seams that they are pretty much the same tractor. Please help.

I have found a 2002 JD 4110, reverser, 2 hours. They are asking $10,000. Is this a reasonable price for the tractor, no equipment, has 2 scv's though.

OK, Here's what I am hoping to get. JD 4110 R4s Duel SCV rear hydraulic outlet Frops (tall hoop for BH) Block heater 410 FEL (ballast box + level indicator) 46 BH I total that out at 23,827 list price from the JD web site. 10% off would be 21,444 15% off would be 20,252 20% off would be...

I am trying to decide between the 4110 and the 4210. I thought the 4110 would be sufficient for my needs but I'm not sure it's big enough. I will be hauling and moving heavy stone, cleaning out corrals and an arena, moving manure and doing reasonably heavy landscaping work requiring earth...

Hello all, I have been reading here for a while, but since I just finished building my new cab, I thought I would show a few pictures. I am pretty proud of this project as I designed and built it. slefevre (Scott)

deleted

I have had my 4110 for 2 months now, It has 29 hrs on the clock so far. I got my new toothbar bar the other day and just wanted to say WOW, I dug up some really stubborn roots that would not come out with the toothbar. I am just rambling... I updated my sig with some pics...

I'm looking at these two - my wife prefers the idea of JD..Kubota seems a few less $$ If there's anyone out there who chose either of the JD compacts I mentioned over the Kubota for any reasons to do with the performance of the machine (ie assuming the dealers are equally good) - I'd be really...

JD with JD loader - 410 loader Kubota with LA402C loader Narrowed it down to one or other of these I think - here in the UK they are similar $$ for each package. I ruled out blue as I don't have a suitable dealer near enough. I'd be interested if anyone has faced the choice I have - and which...

Does anyone have experience using the 410 loader with a JD 4110? I interested in knowing the best size bucket to use to balance the size of the tractor. I want to move fill-dirt, mulch, and gravel. Also how well does it do at cutting into the ground to lift out compacted dirt? Local dealer...

I stopped in at the local JD dealer last night to ask about the 4110 to get their spin on comparing it to a similar size Kubota. The salesman quoted me $20,000 for a 4110 with a backhoe, apparently JD has made one available for this model only in the last month or so. That seems like a fair...

Hi All, I've been lurking on the forums for several months trying to decide on the tractor I need. I have a 2 acre yard and another 15 acres we mow three or four times a year. I think I have settled for a 4110. The dealer in our area has one with a FEL, 60" MMM, cruise, hydrostatic, R4 tires...

In the process of hitting some tree branches I have lost one of the bolts attaching the lights to the rollbar. I can get the bolt from JD no problem. However the bolt is threaded into a knurlled fitting that is pressed into the plastic light assembly. Of course the knurelled fitting is gone...

I am going to buy either a JD 2210 or a JD 4110 . I have been reading every post I can find regarding the 2210 and the 4110. Though I am normally a decision maker I find myself stymied. I have driven both (not much difference in handling I thought). I even have a 2210 in my garage this...

Hi All, First of all, what a great site. I have been browsing for a couple of months. It has definitely helped in making my decision a more informed one. I am purchasing a new tractor and I have narrowed it down to a the JD4110 w/60"mmm,fm blower,FEL. I have been wavering back and forth...

Until yesterday, I had decided to purchase a JD 4110 with FEL, MMM and a few other attachments. I am very impressed with it and it will serve my 5 acres well - Then yesterday I stopped by the New Holland dealeship and drove a TC24D - Very impressed with it as well. Haven't priced it yet, but...

Hi I am currently down to evaluating a JD4110 and a Kubota B7550. I plan on using the tractor for hauling manure, plowing my driveway in the winter. harrowing 5 acres and pulling a manure spreader. I've looked at both models and they are both nice machines. The price is pretty well the...

Hi I am currently shopping for a tractor and have come across a used JD 955. Being a tractor newbie, I'm trying to figure out whether buying a larger used tractor makes better sense than buying a smaller new tractor. I plan to use the tractor to haul horse manure, plow my driveway in the...

I know someone mentioned this before, but does anyone know the part number for the special clips that enable holding the mid-mower up on a JD4110, while a rear 3pt attachment is used.

I know someone mentioned this before, but does anyone know the part number for the special clips that enable holding the mid-mower up on a JD4110, while a rear 3pt attachment is used.

buyjd-ML-233071-ML- Moved to JD Buying/Pricing (brand specific).

I've been using this site for tractor education for a while now and it's been very helpful. I'd like to hear from anyone who's recently priced or purchased a Deere 4110. I've been quoted the following price: Deere 4110 w/HST R4s Folding ROPS 410 FEL 60" mmm Price for all of the above: $15,975...

Hello everyone, I am in the final stages of purchasing a new tractor rather than buying used due to the great financing programs that are currently available. I have settle on either a New Holland TC24 or John Deere 4110 with Hydro trans, R4 tires, 54 inch loader and a 54 inch box scraper with...

Folks , I know this subject has been beat to death so far this winter , however the JD block heater setup is very different from the typical freeze plug setup you would commonly see. So I though I would share my experience with the install. Below is the link to my webpage that describes the...

Is there a brush/hood guard that fits the JD4110? I have a LX4 rotary cutter and would like to protect the front end.

Just thought that I would post some pictures of some of the attachments that I have fabricated and a couple of the upgrades that I have added to my 4110. The attached picture shows the auxillary hydraulics that I have added. I ordered the rear hydraulic kit then purchased a 2 spool valve from...

5\' Box Scraper with JD4110 I am looking to purchase a King Kutter 5' Box Scraper to use with my JD4110. Is the JD4110 able to handle this size of box? Anyone have experience with this?

What is a decent box blade for a JD 4110. Book says the width is 50".

I have pretty much decided on the JD 4110. Here is the price quoted by the dealer (Central Florida area): 4110 HST Hyd for FEL R-3 Turf Tires $11,513 A Woods 60 inch finish mower RDTH60 would be an additional$1850. From the JD site the tractor set up is about $14,500 list. Is this a decent...

I have driven several JD model compacts and like the 4010 and 4110 for size and price. I have priced the following configurations from a local dealer. The configuration is as follows: 4010 - $11,645 (18.5 HP, HST) 60" belly mower 48" LX4 rotary cutter with slip clutch Hydraulics for future...

I am considering purchasing one of the 2 tractors. Each tractor is configured with a 60" belly mower, Power steering, 4WD, and a 48" rotary cutter. They both have similar gross and PTO HP, wheelbase, and ground clearance. Dealer price quotes from yesterday 9/3/02. JD4110 - $12,870 B7500 -...

JD4110 or JD4100 with 61\" Loader Bucket Anyone out there using a 61" bucket on a 4100 or a new 4110 that can offer up coments on how their machines handle this size bucket.

I am a long time reader, first time poster. I am looking to purchase a compact tractor to help take care of my 12 acres. I have about 2 acres of lawn to mow and 3 arces of pasture to brush hog. The other 7 acres are timber. I need to maintain my 400 foot driveway (gravel and relatively...

I'm interested in purchasing several 3 PH impliments that I plan on using on my new JD 4110 HST with turf tires as follows 1) 4' box blade w/scarifiers 2) 5' rear scraper blade 3) 6' landscape rake (or should it be 5'?) Are these the proper sizes for this size tractor? The tractor hasn't been...