john deere 410

Here is a PDF for how I did it. I hope it helps you.

Quite simple to replace the seals.

Good day, I would like to add an additional circuit to the rear of this machine. I would like to be able to run things like a grapple, post hole auger or even wood splitter off the end of the boom. This would make the machine much more useful on a-day-to-day basis. One suggestion from a local...

We have an 83' JD 410 TLB, Used for just a little bit and discovered the hydraulic fluid was real low, filled up. Tractor works just fine in forward/reverse in LOW range but will not move very good in HI range. 1st gear HI and it seems like its slipping, it will move but we stopped trying out of...

I need help I have a 410 Backhoe when I was digging I lost all Hydraulics and will not move but motor still runs. What do you think?

Need a 1,1/4 inch female 14spline sleeve Part#T58193. This sleeve comes off the front of the motor and runs the hydraulic pump

Operated the tractor yesterday, today it won't crank over. ran a jumper wire from the starter solenoid and it cranks find so the battery and starter are good. What should I look for next?

after sitting for a week and a little rain exposed, my john deere 410 c would barely turn over. after some trouble shooting including a smoking starter, I ordered a new starter installed and it fire right up. i stalled it while pushing dirt after the first minute of running and now it barely...

i have a john deere 410c tractor with backhoe. after sitting a couple weeks and a little rain, it wouldn't turn over. the starter smoked so i ordered a replacement and 3 days later with new starter it cranked right up. i then killed the tractor within the first minute by pushing to much dirt...

Does anyone know how to remove the nut to draw out the piston? It just spins but won't back out. Any tricks would be appreciated...

Hello all! I just recently purchased a JD 410 with a fair share of issues. I'm having issues with the drive system and hydraulics. It will only drive with the left stick forward (is this high or low speed?) in 1/2/3 but feels like its slipping pretty bad. Reverse seems tighter and works well...

Hello, Members. I have JD 410 backhoe has some issue that loader boom respond very slowly after 20-30 minute operating the tractor. I am sure It was not hydraulic pump problem because backhoe boom and bucket cylinders works fine even after some time operation. So guessing the boom cylinders or...

Hello, Members. I have JD 410 backhoe has some issue that loader boom respond very slowly after 20-30 minute operating the tractor. I am sure It was not hydraulic pump problem because backhoe boom and bucket cylinders works fine even after some time operation. So guessing the boom cylinders or...

I have a problem with my john deere 410 backhoe. It will move reverse but not forward. I have checked the linkage and the pin and it was all ok. I checked the low pressure PSI for the forward and reverse with a gauge. Reverse was 100 PSI and forward was 40 PSI. I checked the sump screen and it...

Hey everyone I got a new project which is a straight JD 410 backhoe. Completely rebuild the entire motor 4cyl diesel. But the mot back in and now she doesn't want to move. She will go into all gears (1-8) and slightly "jerks" like it wants to move but doesn't. I have to put the pedal to the...

Hello I'm new to this forum and my name is Jack. I just picked up a John Deere 410 Backhoe and it worked ok for a couple days and now it will barely move forward but it moves ok in reverse. I called the guy back and he said that he broke a hydraulic line and he replaced it and it work ok before...

I have a 1974 JD 410 that is in great cosmetic conditions. Looks almost new but the pump is very weak and needs to be rebuilt or replaced plus there is a one leak in the backhoe arm. Tires need to be replaced but other than that it is really nice and runs strong. Does not have enclosure or...

Gentlemen, thanks for the invite to the site. I am in the process of rewiring my machine, any help with parts or info will be greatly appreciated.

i bough this john Deere 410 tlb late 70s diesel about 2 weeks ago and am having an issue when i started Thursday it ran fine for about 30 minutes than stall out let it sit for about 5 minutes and can back to turn it on and the rpm shot up to 2000 rpm and shut off let it sit another 5 minutes...

hi i just purchased a john Deere 410 tlb with no backhoe, year is unknown but should be about the early 80s and i am having issues starting it it has the 4 cylinder diesel and and when i crank it 3 times it kills the battery so have to jump it then starts my question is does it need 2 batteries...

I have recently purchased my first backhoe for use around my home. It is a 1979 John Deere 410 in what I think is fair shape for the age. Typical problems such as zerks that won't take grease, broken window latches, missing window hold open stops, dangling wiring, and misc hyd leaks. I purchased...

How do you remove the spider gears from a model 410 john deere backhoe

I'm looking at a buying 1983 JD 410, however I'm concerned there may be a problem with the reverser or main clutch. When I drive the tractor, if I try to start out in high range 1st gear (5th gear I guess), it is ok on level ground, but it will not move if on any hill at all. Is this normal...

Hello. I am new to the forum, and the thing that caused me to join is that I have a simple question for those of you familiar with the JD 410. I have a backhoe that was my uncle's. Due to estate settlement, I am now responsible for this backhoe, which I have never run before. It is a 1978...

Have an old 1970s john deere 410. My dad was running it yesterday and he was pushing some trees around we had cut down previously. He started to push forward and the hoe bucket was dragging, so he let off to raise it up, then went to engage it in forward again. Well now she will only move...

I started her up, drove over to my fuel tank, started filling the tank, the engine seemed to bog down and then smoothed out and ran back a idle just fine. I finished the fueling, got back in the seat and none of the hydraulics have worked since. I checked the hydraulic pump at the front of...

My 410 backhoe has a leak which seems to be coming from the plug located on the bottom of the pump. I have the Tech Manual and I took the plug out, replaced the O-rings but it still leaks. The machine starts and runs great. Is this an indication of a another problem and what do I need to do to...

Have a 410 in my shop, was brought to me last week owner said clutch was slipping, I did question him as to if he was sure it was the clutch and not the reverser that might be the problem. The man is a know it all and just wanted us to split it and put a clutch in it!!!! Well we did that and yes...

A year ago I was using my jd4100 to mow and all of a sudden the front bucket on the FFEL was scraping the ground. I realized the dump function on my FEL was activiting even though I wasn't touching the joystick. So, the FEL will stay in the raised/lowered position but it won't stop dumping...

I am having a problem with the high/low/park shifter lever. The backhoe wants to move when the shifter is in the neutral position. When you shift it into low the backhoe just bogs down. I also noticed you can pull the lever all the way back towards you on the low side which I don't think you...

Just wanted to show a project that I am currently working on. I need a new (used) loader bucket for my 410. The thing has been very abused over the years and is just too far beyond repair to save. So I decided to make a skid steer quick attach. I ordered the Titan brackets and hardware and have...

I have a late 70's early 80's JD410 loader/backhoe. I used it perfectly fine for 4 hours clearing snow, backed it into my garage when finished, went out 3 days later to move more snow and the loader will not go forward or reverse. I thought maybe got some moisture in the oil or some linkages...

Topping up the trans/hyd fluid in my 1978 JD 410 today when I realized that I was adding the hydraulic fluid for my Case farm tractor. I probably put less than two litres in before I realized what I was doing. How fatal is this? I really do not like to contemplate changing the fluid in the JD as...

I'm helping a friend out trying to find a swing arm frame for his John Deere 410 backhoe (1980). If anyone has any ideas of where I might find one for sale...without cracks :laughing: I sure would appreciate it. Thanks a bunch!

I am Looking at purchasing a JD410 it has two gear levers what is there functions The left one when moved to the left and forward does nothing. Thanks Dan

I have a late seventies jd 410 backhoe that has fresh oil and filters in it. The dry clutch is good. When I try to drive it up hill even in lo range 4th it slips I had to shift to first gear to make it up the hill. Is the shuttle shift clutch pack adjustable? any help would be appreciated.

I have a late 70s 410 back hoe. Just got it out for the first time this spring the first day it worked great. Went to move it today and it will go in reverse fine but take a while to go forward and does not want to pull in forward. I pulled the tranny filter off and it looks bad but I am afraid...

Okay guys, me and my father-in-law took a chance on an old JD 410 backhoe that supposedly had a rebuilt engine 140 hrs ago. Was hard to crank, but it ran good when cranked, so we took it. Had a JD mechanic do fluid and filter changes for us and give it a test run. Diagnosis not good. He says...

My bucket won't stop falling forward. The bucket slowly drops forward until it is completely in the dump position. I hear a small hydraulic sound when I put my ear to the cylinder. I suspect it is a leak at the svc. Any ideas how to test it? Any ideas how to fix it? Thanks

I have a John Deere 410 backhoe. It has a standard bucket on the front and of course the backhoe on the back. I want to make it more 'all around' useful and am considering adding a thumb to the backhoe. I have also gotten pretty spoiled with the usefulness of my tractor, as far as being...

My neighbour has a John Deere backhoe that the decals say is a model 410. The tag on the frame above the right front axle has serial number: 410D 37598T. We would like to know the production year and the model, is it a 410 or 410D. I found on the 'net how to get the year from a 13 digit...

Hello all. First post and I'm in a bit of a jam. First I need to correct something in the title of this post. I ran it out of "fuel" - it's a diesel not gas motor. I ran my JD 410 Backhoe dry on fuel this afternoon. My gauge said I had half a tank but I didn't. She was down to nothing. So I...

I have been having a problem with my 410 backhoe quitting after it has been running for a while. It acts like it is running out of fuel. Let it set for a few minutes and it will start again and run for a few minutes then die again. I have replaced filters, new fuel pump, rebuilt injector pump...

Hello, I have JD 410 Backhoe and one day while digging some roots I put a crack in the bucket up the side of one of the fingers 5-6 inches long. I also have been keeping a close eye on a hairline on one of the connecting arms between the ram and bucket that was welded before. Who should I...

I am looking at purchasing a 1980 JD 410. Are there attachments available for this model? Stuff such as a concrete breaker, or an auger? Where could I find what is available and/or compatible? I see some threads on forklift adaptor and that looks like something I would get.

Hi, I', new here and new to tractors. I am looking at purchasing a 1980 JD 410. It has 2,000 hours on it, which I understand to be pretty low. It runs fine, and is ready to work. What is a good price on such a backhoe? What would be the price range on such a backhoe? Do backhoes such as...

my fathers old 410 needs parts , specificly a drive roller and gear but may be interested in the whole bailer if not to far away

This works, just wondering if anybody'd care to speculate what I might be able to get for it.

I own a 1974 John Deere 410 commercial loader backhoe unit and had a question for all of you who own an older one like me. Mine seems very unstable on uneven ground even when dry, and was wondering if it feels the same on yours. As long as I am moving it's usually ok, but when I push...

Hi Everyone, 1 yr lurker, 1st time poster. Anyways... I was trying to push over a tree this weekend with my John Deere 410D Turbo Backhoe, and the backhoe arm was pushing me off the ground as the tree gave me some fight and I came back down on the stabilizers hard a few times when all of a...

What is an acceptable price or price range of a Deere 410 loader attachment with brackets in good shape? What did they cost new?

Looking for someone with a JD 410 loader. Several questions: I have a box blade attached. Do I need a ballast box? Is the 49 inch bucket OK? Is it difficult to attach and detach the loader on the JD4110? Thanks

Never to early to start thinking about winter! So I thought I would take my old JD 425 front blade and an extra front mount I had laying around and setup a front blade for the loader. Had a little tubing left over from another job, so I welded up a frame and, threw the mounts on and then...