john deere 14t baler

Hello folks, I have a JD 14t baler that has been working fine over the years. I got it out this year and with the old twine it would bale and tie but the right side would break right after the not. So I cleaned everything and regreased. it started working again and then neither side would tie...

If the PDF doesn't work for you, go to the address below for the same manual online which also contains the manual for he version with the motor mounted on the hitch. John Deere 14T Baler Manual

Hi- I just joined the group and am trying to send a general call for help to anyone who might know how to install a knotter on a JD 14t baler. I bought this 14t baler 2 years ago and have baled about 200 bales with it. One knotter works fine, the other one (the inner one) stops tying abut...

Have a new to me jd 14t Baler. The oil seal where the plunger crank shaft enters the transmission (for lack of a better word) is leaking. I posted earlier today looking for advice but for some reason all messages got erased? Anyway...I tore into this today and now realize the entire transmission...

Hi, I have a 14T baler, with manual, and have some issues with one of the knots. The left one (if you are on the tractor) is quite often loose. When I use the modern plastic twine, 1 out of 3 bales fails. The knot is being made, but loosens before the bale makes it out of the machine. When I...

My neighbor down the road is looking to bale about a 200 bales from a small field using a 14T and his JD 1025R 25 HP small tractor. All flat land and dropped in field. I told him I had my doubts. He picked it up for 500 bucks in working condition. I know this baler has low HP requirements, but...

Looking for some help! The needles on my 14T broke the other day and was able to find a set from a tractor graveyard about an hour away from me. They were off of a 14T as well, and look great, but when I installed them and then tried to manually advance them to adjust, they don't seem to lineup...

Hello all. I bought a JD 14T baler and have been getting acquainted with it slowly. The guy i bought it from got it from a neighbor who said it had been shredded for over 20 years. I figured for 300 bucks it would be a good learning experience if nothing else. Anyway, I bought the manual...

Good morning..... This is my 14T baler.... I've had it for about 4 years and tweaking on it to keep it working very well..... Replacing parts as needed.... The knotters are last on my list due to my ignorance and lack of parts available... I'm ready to tackle the "Twine Disc" timing issue...

I am looking at a JD 14T baler. It is in good shape and is baling but the left knotter frame is cracked. Is this knotter frame interchangeable with any others from JD?

Got the baler out and figured that we would go without a problem and it won't tie a knot, the needles even lose the baling twine some how...we have just been running it through the cycle by hand with no hay in the baler, don't understand it was working fine when we stopped haying last...

I have a few questions on this baler. Hope someone can shed some light on this.. IN the pic. The pink circle is loose.. Questions is why? The blue circle has bolt missing? The red circle.. Are the brackets broken off and welded higher than normal? Thanks B2R

which one (if both work properly) would y'all get. same price when calculated for the exter gas to get the 214ws

...we are still searching for an operators manual on this unit...soooo, can anyone talk me down on how to set the timing (are there timing marks anywhere ?) -- particularly: what position should the "plunger crank" be in for timing

Here's my problem: Knotter is not making a full revolution when tripped. The trip dog roller makes contact with the trip arm (to reset the roller) too early it seems so the cam on the knotter clutch stops rotating the knotter gears. The result is that at the end of the knotter cycle the...

I've got a 14T that I haven't used in a few years. Got it out of the weeds, cleaned up, greased, checked timing etc. When I ran a cycle by hand the knotter didn't complete a full revolution (which of course meant I had to retime). It continued to have the same problem every time I ran a...

I am looking for a john deere 14t baler part (yoke rear) Parts number BP14507E email me at : dairythings@gmail.com our baler snapped this part and we cant seem tofind one that will fit the u joints. this is a 1"x1 1/8" square shaft with hole in the neck.:confused::confused:

I am new to the whole haying process and I am going to look at two differnet balers both suppost to be in good "field ready" condition, one is a Ford 530 baler and one is a JD14T baler. WHich is a better baler?? Also I have a guy near me who would sell me a kicker a JD model 40 and I would also...

The pitman is "busted half in two", bent beyond measuring. I'm in search of a measurement of the pitman from the center of the wrist pin on the plungerhead end (there's a grease fitting at this point) to the center of the end cap joint on the crank end. I've made a clean cut on each end and...

First off, I'm glad I found this site!! Secondly, go easy on me, I'm a gal!!! Anyway, the problem is, our baler will not tie one side..it ties the oneside every single time, but the other side never ties..we've rolled it thru by hand, watching everything, dad adjusted the tucker finger a few...

i have this on my parts baler. is it worth transferring over? does anyone have a operators guide? .

Hi all, First off, just like to say that I'm glad i found this site, tons of usefull info! :) Anyways, I seem to have gotten myself into a much bigger project than I anticipated... When we moved into our house 4 years ago, there was a baler out in the field under a (very shredded) tarp, which I...

What type of twine are you running. How short have you ever made the bales. i have been trying to make them small for the wife to move but the bales does not seem to like it. They come out shorter on one side.

For the last few years i have been buying hay for the horses. Well, as most of you probably know, Hay is starting to get expensive and I have about 30 acres of Timothy hay just waiting to be baled. So, my wife grandfather is giving me his 14T baler. He said it ran fine 6 years ago when he put...

Found a 14T baler at local JD dealer, said it needs a shaft that operates the Knotters, anyone had any experience with this and how big of a job is it to replace it? Wants $500 as is, 265 for the shaft and $1200 if they put the shaft in. Not a bad looking baler, chains look good. Thanks Steve

I've been bringing a 14T back to life that hasn't been used in years. When I started it was shearig bolts all the time, so I retimed it. Looked like it was going to work great and then a chain link broke and left the needles in the way of the feeder teeth. Broke off the inside needle when the...

I just wanted to put a message up here and let you folks know that my father-in-law's TC30 worked real nicely this weekend running a JD side delivery rake and square baler. We didn't do very many bales as we had some other projects to work on, but it was a lot of fun. I will post a picture...

I am replacing the chains on my newly aquired John Deere 14T baler... The one at the front near the slip clutch went on fine. The one that drives the feeder arms though was much tougher...The old chain was 42.5 links of # 60 chain, I tried 43 links of # 60 chain and it was to long ( I tried...