ford naa

Has anyone used a Woods RD 7200 with a 1954 Ford NAA? To hook them together, I had to point the pins towards each other because the lift arms do not spread far enough otherwise. Because of that, I can't figure out how to attach stabilizer bars. Is there something weird about the NAA that makes...

Im in a mess..3 pt wont lift so lifted top off...replaced piston and seals and pin that was worn then tried to addjust as per video.but when i bring arms up to botton of spring there no way i can adjust..prob 2 inches free play BUT if i lift arms up above spring..i can adjust 3/16 and 1/4 as per...

Im looking for teflon seal for lift cylnder..1954 forn naa..pistion is 2.5 inche dia i cant where to buy tefon or neoprene..i wrecked 2 leather ones...any assist where to purchase

I bought a used Woods RD 7200 finish mower to replace my old KingKutter 72" finish mower. In attaching the Woods to my 1954 Ford NAA tractor, I found that the hitch pins on the Woods are 3 inches farther apart than on the KingKutter. Result: The anti-sway chains were too short and my old...

So it's a fix one thing find another kind of tractor it seems. After *ahem* fixing the fuel issue, found a leak in the radiator. Long story short, 2nd replacement radiator is holding coolant so that's fixed (for now at least). During the course of burping the radiator I decided to start checking...

I bought a 54 NAA from a guy a week or so ago and I'm stumped. Tractor fired up, ran around his yard, picked up a 5' Box Blade and drove onto my trailer then stalled out and battery died before getting it started again. No biggie, older battery, had started and stopped a few times so maybe not...

I have a Ford naa jubalee tractor. I have updated it to a 12volt negative ground electrial system with electronic ignition. I have spark at the spark plugs and fuel. I am trying to set the ignition timing and it won't start. I have set the flywheel to the 8* tdc mark at the indicator line...

I am being gifted a 54 ford jubilee tractor and I am trying to figure out what attachments will work with it and would love all of your help! I have never used this kind of tractor before and have limited tractor knowledge since most of my experience has been no-till. I am transitioning...

My NAA is leaking between the hydraulic pump and the flange at the bottom that holds the pressure and return lines. Before I remove the 3 bolts that hold that flange on, I would like to know what is in there. It appears to be one or two O rings. Has anyone ever replaced those O rings? ARe...

I have searched forums and the RAL 7001 is the only listing I see. This is too grey for my eye. Has anyone had nice results with any other supplier?

New to this forum . Just pick up a 54 Ford NAA this past weekend . The rear wheels are loose . Ive read about the hubs being worn out and causing this problem but on one side the axle nut or axle seems to be stripped when you try to tighten it . Has anyone had experience with wheel clamp lock...

Hi. I have searched for an answer, but come up with zero. I hope to get some help. My dad has a 1954 Ford NAA. It has a loader and power steering, even though I understand that NAA did not come with PS from Ford. I think I have identified the loader as a Davis, and in the Colo Springs area I...

Good morning, This is my first post. I live near Waterville NY and have a 1954 Ford NAA that I have owned since 1983. It came with a heavy plow on the front that I use for snow plowing. It raises and lowers with a cable going back to the hydraulic arms for the 3pt hitch. It started giving me...

First post here but have learned a lot from these forums so have to say thank you! I will try and make a long story short... I have a very nice NAA with vane pump that wouldn't lift a heavy load and had a leakdown issue. Hydraulics seemed to work fine other than this. They were responsive...

Picked up this orchard tractor a week ago in order to have a dedicated mower setup. I don't know about the rest of you, but after struggling with removing and installing your typical three point attachment, I am usually too tired to finish the job I installed the attachment to do to begin with...

So I got a new radiator for my 1954 NAA. Today, I worked on getting the sheet metal off. Nightmare! There are several bolts and screws that go into captive nuts. With few exceptions, the captive nuts rotate in their cages when I turn the screws. Yes, I used PB Blaster. I keep finding more...

hey all, I recently picked up a 1954 ford naa and I am having a hard time finding out what fluids to put in it. trans, motor, etc. was hope'n someone could point me in the right direction. i have the super s premium hydraulic fluid. what all can this be used in on the 1954 ford naa, if at all...

I was wondering if there was a newer owners manual printed in 1954 or if Ford had the same from 1952/53. when it was printed until end of production? Also, I have found that a gear change was done in 1954 on the NAA. Does anyone know what the ratio changed? It states that 6.66:1 was the original...

Hi there, new here. My boyfriends 54 NAA will not hold prime on the hydraulic pump. We got this tractor a while ago, and when trying out a back blade, hit a rock and after the lift would not work. Decided to do a refresh on the pump and lift cylinder. ALL new parts in the pump which works great...

Looking for a source for the 4 bushings that go into a morflex 302 coupling center hub. I removed the driveshaft and the bushings are quite worn and should be replaced while apart. Thanks, Pete

Are there any preferred grades or specifications for modern lubricants in antique tractors. Mine is a 1953 Ford Golden Jubilee.

My in laws NAA lift stopped working, so I picked it up and brought it to my house for repair. The clevis pin broke allowing the rod to fall out of the piston. Drained the reservoir and found what looks like a brand new seal in the bottom of the housing. It measures about 1.5" I.D. and about...

I did an oil conversion and will give you the canister cover EAA6737B and the bolt with oil holes in it.....Free to good home. Rear fuel tank support bracket NCQ 9097A also free....new tank came with one. You pay shipping.

I just started working on my great-grandfathers 1954 Ford NAA that has been parked in barn for at least 5 years but no longer than 10. I am as green as you can be with tractors (first time on one was two weeks ago on this one) so please bear with me on the terminology. I replaced all fluids and...

I finally went up to the farm and got my non-running NAA up on the trailer with what turned out to be a defective winch. When I bought the tractor, the previous owner loaded it up on the trailer, and I can't remember where on the trailer it sat. I'm going to transport it tomorrow, and via...

Ok to begin with, I'm a transplanted Hawaiian in Tennessee who decided to buy a recreational piece of land. Got a good deal on a running Ford NAA, and without knowing a whole bunch took the plunge. Now realize I can work on boats, rigging, fiberglass, etc...and build cabinets, handy but I am...

Does anyone know where I can get an exploded diagram for an old vicker hydraulic pump? It is off a shawnee loader that is mounted to my NAA. The pump drools a pretty good stream of fluid from around the shaft when it runs. The shaft appears to have a bearing behind a snap ring but I can't see...

I have a 1954 Ford NAA that sets all year in a shed in the Upper Pennisula of Michigan. I just use it for putting in food plots for deer. Now this area is pretty remote I have no electricity etc so everything is pretty much just get it done. Some years the old Ford can be a bit troublesome to...

I have solved a difficult and nagging problem that would have taken only 5 minutes if I had known what I am about to write about my 1953 Ford Jubilee edition NAA tractor. The problem was the 3-point lift. It worked fine, but would often be unresponsive after the tractor sat unused for a day or...

Seems like the rear seal of my hydraulic pump for the 3 point hitch just let loose. I thought it was the o-rings where it connects to the lines, but after checking it more closely it's leaking right from the seam of the back portion of the pump. I was told that I probably overloaded the...

As a new owner of a Ford NAA, I am wondering what that proper service levels of the transmission, hydraulics and rear end are. I have the manual which gives the quantities, but how do you see that they are up to proper level? Thanks.

I've called a number of places looking for brake drums. A number of dealers list the drum on their web site, but when I contact them, they are sold out. Is there some reason that the NAA/8N drums wear more than others so that there is a huge demand? I assumed that mine are bad because a...

what oil should i run in a ford naa (summer use only)

Posted in wrong area sorry

Is there a way or can I tap off the hydraulics on this tractor. It does have the new style hydraulic pump (piston type). I want to make a quick connect point so I can run a log splitter or maybe some other hydraulic option at the back of the tractor. Thanks for your help!

Installed new oil pump .. repaired distributor. Cannot find timing marks on flywheel to install distributor at the right crank position tried just do it by #1 piston still no luck...Have gas and spark wont start..even have oil pressure. Where are the timing marks ...worn off??? Any help would be...

1953 Ford Naa Jubilee - Clutch slipping - Which clutch to order ? 10" or 9 " ? when looking to order a Clutch kit there are two options - 10" or 9" - Which should I get ?

1953 Ford Naa Jubilee - Clutch slipping - Which clutch to order ? 10" or 9 " ? My clutch is slipping and I am planning on getting a Clutch replacement kit - As I am looking I am seeing two different kits... Some say 10 " , but most say 9 " .. Which kit do I need ?

Hi Gang, For the last couple of years, while brush hogging the fields, the tractor has NOT run good at all! I thought maybe, it was a "fur ball" or something from ethanol, but have never been able to pin anything down. It did seem like every time I dropped the fuel bowl and screen, it would run...

My NAA has been losing oil pressure for awhile and now it is at zero, dip stick shows clean and full, too clean after running about 30 hours with low (10 psig ) to zero. The oil looks like it was changed yesterday, I installed a spin on filter system 7 years ago when I had the entire motor...

I'm looking for a picture of the Ford NAA throttle stop (that I believe bolts to the manifold and hangs down around the throttle control near the governor). I assume other 134 ci engines have the same stop, but I am not sure. Mine is missing and I'd like to make one that looks like the...

I have a 1954 Ford NAA. I have had the tractor for 30 years and it was missing the hydraulic pump when I got it. Someone made a plate to cover the place where it bolts to the engine and had cut and brazed the lines at the back of the tractor. I decided to try to get the hydraulics working. I got...

I may have reversed the poles of my newly charged battery when placed into the NAA (original 6V system). The tractor started up fine but when turned off the generator kept turning. Yes, the fan belt was loose and the battery was turning the generator! I had to disconnect the battery to stop...

Went to use my tractor to do some snow plowing and when I attempted to raise the back blade it wouldn't move off the ground at all. I thought it was frozen, but moved the tractor a little bit back and saw it was free. Made sure the tractor was nice and warmed up, then tried the lift lever...

I shut off my '53 NAA this evening for a couple minutes and when I went to restart it the solenoid just clicked. Tractor had only been run a couple minutes (backing load of corn in the barn) so it wasn't hot or anything. Tried to restart it a couple more times and same thing. Then held the...

A friend of mine has a 53 or 54 Ford NAA that will not run. He has spark at the points but not at the cap. Any ideas on what this could be caused by?

Rebuild 134 engine including new oil pump. initial start-up sounds great, but no pressure on the gauge. I removed the dist, and fashioned a long screwdriver to turn the oil pump with a drill, giving good volume flow out the filter port. New gauge and still no pressure. Is there a pressure...

My '54 NAA has been doing fine all summer. Last evening, I started it to do some mowing. It did not want to start, and that has never happened before. With the help of some ether, I got it going. It was billowing a large amount of bluish smoke out the tail pipe - also never happened before. I...

I have my newly acquired NAA just about ready to go into service. One thing I've noticed is that the clutch really has a different feel than the one on my 9N. The throw is a lot shorter and it feels softer. In gears 1st thru 3rd and reverse, the tractor takes off very quickly if the clutch is...

I just bought a 1954 Ford NAA and I am in the process of doing the usual tune-up and fluid replacements. I changed the oil and used 10W30 which is what I use in a 9N I have. The tractor starts quickly and runs very smooth but the oil pressure guage didn't work when I bought it and upon replacing...

How do I charge a 6 volt battery ? Is it reversed , positive to negative post and negative to to positive post ? Thanks , Terry:confused2:

Can anyone tell me if a 2000; 3000; 4000 transmission will fit on a naa? Thanks

I just replaced a jubilee steering box with a used one...All is good with the box except the top Steering bearing assembly Bearing Assembly - 8N3517 is bad and doesnt seem to want to come out.I am speaking of the one right under the steering wheel itself.....without the bearing assembly, the...

I'm retired and just purchased a Ford NAA with a Sherman Backhoe. Plan to restore it and would like to contact other NAA owners, especially those with a Sherman backhoe.

Hi, I just changed out my NAA distributor with a used one. Tractor starts and sounds good. While taking it for test spin, I noticed that it didn't seem to have any oil pressure. It never did have terrific pressure, especially when warm ... but it did have some. According to the manual, the...

Will a five-foot pto tiller work okay with a Ford NAA? Tractor has 4 forward gears. I have clay loam soil.

My old snow plow truck leaks tranny fluid awful. I mostly haul wood and push snow. Would like to put the plow on my Ford NAA but am not an engineer. Anybody done this?

i just bought a '54 Ford NAA, looks to be well taken care of. Question is....at 800 rpm, not at normal operating temperature yet, 40 degrees outside - when i move the lever to raise the 3 pt hitch with a 4ft bush hog on the back, there's about a 5 second delay before it goes up. it goes up...

Last weekend I was mowing with my '54 Ford NAA. After 30 or 45 minutes, it started running rough and losing power. I barely made it back to the house. Thinking it could be a little dirt in the carb. I drained the carb and cleaned the sediment bowl. I mowed for a while and the same thing...

In the previous thread I mentioned that I was at my neighbors moving a house trailer with my Fordson. One of the guys who ended up taking the trailer was trying to tell me that my tracor was Ford Jubilee diesel. I informed him that it was a Fordson and that is made in England while the Ford...

I've got a 1953 Ford NAA Golden Jubilee with a leaking gas tank. I had it "fixed" about 15 years ago and it's starting to leak again underneath where the mounting bracket is welded / spot welded to it. A few questions: 1. Should I have it fixed again? (it was braised by a tank repair shop.)...

I have a 1954 NAA that I am using with a 6' King Kutter finish mower. I have shortened the chains on the 3-point hitch to limit mower sway. Questions: How much sway is acceptable? I see that sway bars are sold on some sites. Should they be used? I need new chains anyway so should I buy ones...

When I press the right brake pedal on this tractor, or even at times if I don't, the right wheel locks up and does not release until it is dragged along for a while. I'll pull the wheel and look, but has anyone else been through this? Could it be as easy as a missing return spring, or do these...

When I press the right brake pedal on this tractor, or even at times if I don't, the right wheel locks up and does not release until it is dragged along for a while. I'll pull the wheel and look, but has anyone else been through this? Could it be as easy as a missing return spring, or do these...

My NAA came with the vertcal exhaust stack broken off and a Harley motorcycle muffler stuck on the stub. I ordered a new pipe, which turn out to be a nicely bent sheet metal pipe. The issue is that the mufler connects to a casting that seems to have been made in one piece with the original...

Father-in-law has on his to-do list to build a log splitter. So far he's only been collecting the various bits and pieces for the splitter. He intended to run this off the hydraulics on his old Ford NAA, but hadn't gotten to the point of really figuring out how yet. I started looking into...