farm pro 2430

How do I bleed the air from hydraulic system after replacing a couple lift cylinder lines and cartridge filter?

Anyone know what the compression should be on jinma/farm pro 2430 tractor? Can't seem to find any good data on it online.

I have a 02 Farm pro 2430 that has bad fuel smell from exhaust ( burns eyes also ). I'm no Diesel mechanic, and live in more of a city area. So not a lot of mechanics that work on tractors. Can someone please explain to me how to adjust timing on injection pump? It seems that may be my...

When I bought my Farm Pro 2430, all of the 3ph components were missing. Basically, I need everything shown in the attached picture AND a drawbar. I'm going to make some assumptions in my purchase, and I would appreciate any feedback on where my assumptions would be wrong. Any advice on the...

I bought a 2004 FarmPro 2430 with FEL and a backhoe, the FEL works as it should, the backhoe needs some love. I'm having no luck finding a readable diagram of the various control levers in the seat area. One lever in particular is eluding me as to it's purpose. Whatever is does, it seems so be...

First time post but long time forum reader. Farm Pro 2430. Two hydraulic pumps. FEL and three pt. stop working after about 1 hr.in 90 degree heat when using brushhog. Power steering (on the other pump) still works. If I let it cool down it (FEL and 3 pt) will start working again after...

I have a 2003 Farm Pro 2430, it's ideal for what I use it for. I had to remove the fiber dash to clean fuel tank out and notice some wires hanging loose. The tach, fuel, oil pressure, and volt gauges have never worked. I am hoping somebody has a 2430 ( a 2425 might be the same) and would be nice...

I have a farm pro 2430 with 170hrs. It had been sitting for 10 years without operating. I have the tractor running well but have one remaining issue and would like a little help getting started. The 3 point lift jumps when hitting the top of the stroke. It does it in any position the draft...

HELP!! I have split my Farm Pro 2430 to replace the clutch. I installed both clutch disks and put everything back together. PTO engages just fine but the drive clutch does nothing. It will grind when I try and put it in gear. I readjusted several times with no luck so I split the tractor today...

Hello, I have a Farm Pro 2430 that does not move regardless of what gear you have it in. High, low, 2 or 4 WD, it doesn't move. I lifted the front end off of the ground with the bucket and tried the 4WD to see if I could at least get the front wheels to spin but no luck. It almost feels like...

Hey all, Ive been lurking here for a while gathering information and reading posts to help decide a tractor for our 5 acre homestead. Finally made a purchase of a used 2430 with loader and backhoe after considering budget and application needs. Pretty excited about the tractor, got a few bugs...

Hey guys I have a 2006 Farm Pro 2430 with the TY395i engine. It overheats when I use the bush hog or finish mower in heavy grass. 1. I removed the thermostat first. 2. Replaced the radiator cap. 2. I then replaced the factory temp gauge/sending unit with one that reads Fahrenheit. Both show...

I may go look at a 2430 Farm Pro, Koyker loader with a box blade and brush hog.. I know these are Jimna tractors and are a cheaper alternative to the big names, fit & finish is questionable also. I don't really care about the pretty part because it's gonn a get scratched up etc. This tractor...

:confused: having issues with steering. Changed fluids in hydraulics two months ago and since can't steer properly. Steering is loose and have to move steering wheel a few rotations a lot of the time before can get wheels to move. Can't use in this condition. Has anyone else had similar issues

Yesterday I was plowing snow with my 04 Farmpro 2430 (It's a 30 horse Jinma, I think). The tractor has about 50 hours on it and I regularly maintain it. It has a Koyker front end loader and I use a box scraper on the 3 pt. Well, there I was plowing along and the tractor came to a stop made a...

Just wondering if anyone has converted the push/pull type switches to the rocker-type panel switch ? David

OK, Just getting ready to do much needed maintenance I have drained & changed Gearbox & ready to change engine oil & hydraulic oil I found drain for oil & 4x4 axle, but I don't have location pin-pointed to drain hydraulic at 3-point (Rear) Looks like a remote stub on the right lower side...

I have a 2430 Farm Pro 3 cyl. tractor. I had a tractor shop disassemble and clean the fuel injectors to make sure they were in good condition. The only problem is the shop didn't know what to set the fuel pressure at after they disassembled and cleaned the fuel injectors. Any know what the fuel...

Hello to all, I have been reading this forum for a couple years, and now I finally have a question. Can anyone tell me where I can get a starter switch for my farmpro 2430 2005/2006 vintage tractor?

Many of the things that came with the tractor in boxes were not passed on to me yet, and I have lost faith in the seller. I am poking around for some of the components that may be nice/handy. I think it was supposed to have a tool box, but I am not sure. I am talking to Affordable Tractor, and...

Last weekend, I did a bunch of work on the tractor, and I took pics. I made a slide show, and most of the pics have a description. Both ball joints have a broken piece in it I will call a "dish." The spring pushes the dish against the pin ball. Are the dishes available separately? Here is the...

need operating manual and maintenance manual for farm pro 2430

Hello everyone, I've been eyeballing 4wd tractors for a while now and saw a FarmPro 2430 for sale locally. It is advertised as super clean with ... KOYKER 160 FRONT LOADER 6' SCORPION MOWER BY J BAR 5' CARONI SPA TILLER- FL1400 C SPEECO HITCH BLOCK HEATER And only 90 hours...

My father, who had alzheimers has disconnected the guages on his tractor and I need a wiring diagram to re connect them properly, so the tractor will operate. Any help will be appreciated. Brian

Hello All, I have watched the forum for two years now and have added 185 hours to my FP 2430 in that time. Aside from the standard complaints, the tractor has served our 128 acre farm well. The one thing I cannot figure out, though, is how to use the onboard hydraulics to operate a hydraulic...

Hello, I'm considering buying a FarmPro 2430 with a 6' brushhog, a 6' finish mower, a 6' grading blade, a posthole digger, and a lifting boom for $15,000. The company is called Triple T Sales in southern Missouri. This would be a site-unseen purchase through E-Bay. The tractor would be...

has any one bought a tractor like this on the net un seen? i have did a lot of looking and think this might be the tractor for me? i am considering a farm pro 2430 4x4 with loader, 6 brush hog ,6 finish, 6 grading blade, a post hole digger with 12" bit and a boom pole lift for 15000k the company...

hello i am thinking of buying a farm pro 2430 with a loader. has any one had or heard of any good or positive things about this machine? any info would be helpful. thanks

Hello everyone! This my first post. I am purchasing a Farm Pro 2430 tractor. All of the specs. you see on this tractor say that the engine HP is 30. However I have been told by several different people that this is the pto hp and that the engine hp is more. I know this is true on the grey market...

Need help finding 180 /185 thermostat for my Farm Pro 2430. Thanks

Hi, My FramPro smokes quite a bit when I first start it up. After it warms up a bit (never really warms up with the stock 57deg C thermostat) the smoke subsides somewhat. I have to get it out of the garage real quick or else the smoke will kill you. I recently put a rain cap on the exhaust pipe...

Bought a farm pro of of Homier, Bad mistake but got to deal with it now. After 3 months vavle stuck in head, they said it just needed polished. I disputed that but they so called fixed it under warrenty. Guess what? Vavle is sticking again 1 year later. Nobody there wants to hear my problem...

Really excited, drove it with temp outside at 8 degrees,little slow starting, glad I installed heater. Filled fuel up, is leaking out top were fuel gage goes in, so far only problem,changed oil and filter ,hope it warms up.

Recently my neighbor and I each purchased a Farm Pro 2430 with the Chinese loader. The loader on his tractor lasted about 4 hours before the eight attachment bolts at the back end of the loader sheared off. The front points of attachment of the lower arms also failed at the little gusset...

I'm about to purchase a 2430. seems like a really good deal compared to the other guys. Anything good or bad to say about this tractor?

New user ,great site. Just bought a 2430 . Amp meter regersters 0. Batterys were half full. Then checked alternator,idle speed12.6volts,2000rpm 13.0 volts.It says its a14volt alternator. Is this normal. Thanks,Ricky