cylinder

Hi all, Seems I need a Subaru EH72 head, as my left side head has dropped the exhaust valve guide. I could possibly have it sleeved to make up the difference (maybe). I thought I’d check if anyone had a spare they would part with before got the machinists involved. I didn’t lose the c clip, it...

Anybody have a part number for a replacement lift cylinder on a bobcat 9TL Loader. I have searched all the numbers on the cylinder and cant find anything. I also cant find a parts manual online for the 9TL

Does anyone have the exact specs on the bucket cylinder for a BH75 backhoe? I bent the rod digging in some rocks. A new cylinder from the stealership is almost $1000. I can get a new rod machined, but if I can find a matching cylinder for cheaper, I’d just as soon replace it. I know Kubota...

Can anyone help me I have an old loader with Du-al30228 hydraulic cylinder that I need to replace. Any help on how to find one. Thanks

I have a Massey E 2860 with a FLX 2815 loader. Has anyone heard of the role bucket roll cylinders bending? I have a 40 year old John Deere and have had to replace the bucket because of the pressures I put on it and I’ve never bent a cylinder. This seems unbelievable that the cylinder rod could...

Hello, I am restoring a Caretree 524-3P Spade, I have removed several cylinders to take over to my local cylinder rebuild shop. I am unable to get the up-down lift cylinder free from its lower pin. The pin moves back and forth until the cylinder hits the tubing protecting the long pivot pin. It...

Hey all! You do not have to purchase any special tools or pay a shop to install these difficult to install seals. Here is an easy DIY I found and had my mechanic watch it and perform the procedure. It does seem easier if the vice jaws are smaller. I think the best twine/rope to use is a smooth...

I have cylinder stops (these; same function as u-channel designs of varying polish), which I bought for when I needed to be working under the arms. I need to use my forks to hold a work platform. I can tie in, so with the FEL arms safe, the "worst" that could happen is a complete hydraulic...

I recently added some Lucas Upper Cylinder Lubricant additive to my Kubota M70/60 by mistake thinking i had the bottle of anti gel. Anyway, no harm done so I went about my usual routine. After awhile I noticed the DPT cycle had not engaged in the approximate interval I was accustomed to...

So I'm trying to reseal some hydraulic cylinders on a tractor I've saved after sitting for over 10 years. I'm starting with the loader boom cylinders, and I managed to successfully get the gland nut off the first one. The cylinders employ a non-threaded gland nut with a "twist-in" retaining wire...

I have 35T Husky(Speeco) splitter with a blown rod seal. I am sure the cylunder is Chinese but I would like to reseal it if I can get the gland/head out. I dont see any holes for a spanner or a retianing ring. There is a socket head screw and washer in the gland that looks like it would be for...

Greetings all. I was given this cylinder from a retired gentleman (who has no idea what gas it was), and honestly thought it was empty, but after freeing up the cylinder/valve protective cap (took a while as it was rusted..), if I crack the valve, I get what i believe is the sound of gas still...

Anyone know the trick to getting the end off this? I've found no snap rings, no pins, and only that one tiny hole in the face with that Allen head are in it. Can find no vids or pics of this type.

I picked up a Chinese sickle bar mower that has a single action hydraulic cylinder, power up/gravity down. My Kubota tractor has a single set of rear remotes on a dual action control. I don't understand hydraulics nearly well enough, but I'm guessing this is a problem in terms of using this...

I had noticed a while back movement between the steer cylinder and the steer arm thing that ties the steer cylinder and the tie rod together. Of course, I Was busy, in the middle of trying to get stuff done and bookmarked it for a later date. I looked up the steering parts on LS parts web page...

Im needing a cylinder head for 1985 ford 1710. It has a shibaura H843. Anyone know where I can purchase one? Will a shibaura N843 head fit?

I am building a roll-off dumpster truck. I would like to control the bed lift from both inside the cab and outside. Is this possible? Do you all have any suggestions on which setup would be best? I plan on mounting either an engine-driven pump with a 12v clutch or a PTO pump. Both will have to...

Hey everyone I have a mf 1016 loader the cylinder used to raise the loader on left side is damaged having trouble locating one the one I have is non fixable any ideas? Thanks

Newbie. No service manual. Left lift cylinder started squirting oil after lifting loader bucket full height. Purchased seal kit from dealer to rebuild cylinder. Removed gland nut and rod from cylinder barrel. 1.5" socket, 1" drive 40" breaker bar with 36" steel pipe extension was able to break...

On my previous tractor there was a screw on the valve that controls the rear remotes. Turn the screw in to control dual acting cylinders on an implement. Turn it out to control single acting cylinders. How does this work on my TYM built tractor? I don’t see a screw to switch it to single acting...

Pictured is former Alaska First Lady Bella Hammond checking the oil on one of the generators at their cabin/homestead on Lake Clark, Alaska. This homestead is in the registry of Historic Places. I've been reading Dick Proenneke's journals, and in 1978, then governor Jay Hammond picked him up...

Will the 4 cylinder engine bolt up to the 3 cylinder’s bel housing, the look to share the same bel houses?

2010 Kubota L2800 started spraying this tiny leak.Where is the best place to buy only what i need?I assume it needs a seal pack of some kind,but not 140 bucks for 6 or 7 rubber o rings.Any help would be appreciated

I have a 2000 NH 2120 with a 7309 front loader. The right lift cylinder is leaking and I would like to install the new seal kit. But I can not budge the cylinder head (end cap) at all! A couple of questions: 1. What is the correct direction to spin the end cap? By looking at the retainer...

I did something dumb, put too much load on my loader with the cylinders fully extended. I bent both of the lifting cylinders, to the point that they are spewing oil around the seals when they retract. What are my options here? I was going to see if I could get a generic cylinder replacement but...

Helping a friend with a Ford 1715 (Shibaura ?) 3 cylinder diesel. While chasing another problem, we dropped the water separator bowl. Of course that put air into the fuel system. We were able to bleed #1 and #2 at the injector, but we can not get #3 to work (clearly NOT injecting as cracking...

Question my Woods C114 has a cylinder that only has one hose aka single acting (power up and gravity down). I just got a New Holland factory valve for my TC45DA that did not have a valve from the factory and is spring centered and can power in and out aka double acting. If I plug a single...

Howdy folks! It's been a while. OK, so it's not that I'm a slacker... it's just that I bust a$$ all the time and there are some projects I never seem to get to. I've been 'kicking the can' on my leaking backhoe cylinders for years. I have a bunch of cat litter pans that I keep under the...

Hi everyone, I am new to the group. My question is does anyone have the correct part number for the master cylinders on a 1999 Fermec 640B skip loader? Thanks, Justin

Does anyone have a copy or can send me a copy of the Key cylinder diagram on the tractor listed above, TIA, ken kenben41@hotmail.com

Is there an aftermarket or automotive replacement for the tie rod end for the end of the steering cylinder? I think Deere wants around $235 for it. I didn't know if anyone cross referenced it to an automotive one.

Anyone with a montana 2740 know or can measure length of loader cylinder? Rebuilder lost my cylinders so need replacement size. I have bucket cylinders still attached so just need length pin to pin in collapsed position of loader cylinders.

Well about 7 years ago my M4700 left side boom cylinder leaked (linky) and I had it repaired at a reasonable price. But that guy seems no longer available and now my right cylinder needs rebuilding. Looking at Messicks a rebuild kit (just the rings) is about $50. Numerous Youtube videos...

Hello all. I'm relatively new to the tractor world, or really any hydraulics in general. That being said, I'm the type that fixes everything myself and tries to become an expert on anything I own. I have had an Allmand 425 TLB now for about a year. It has been a wonderful machine with tons of...

HELP I was pushing brush and somehow the bucket release lever got puled on one side. It looks like I may have bent the cylinder rod or something. The left cylinder lacks about 2 in retracting all the way in. Works fine other than that. Can't get the bucket back on no way possible. Need some help...

Trying to get left bucket elevator cylinder off. Lower snapping no problem. Upper one not normal snap ring but is very thick with only a split, no holes like snap ring. Any help would be appreciated. Large snap ring tool won't get it? Help please

Sooo, my new to me my 2005 LW8 backhoe has one cylinder which has a leaky seal. The cylinder rod had some spotty rust which upon cleaning up still had finger nail noticable abrasion. On the time sucking vortex it seems the cylinder rod could be brazed and cleaned up, with new seals then...

Bit of a long shot as I don't suppose there are many owners of these on here, however worth asking. I've recently acquired one of these brand new and very cheap on account of the Hydraulic cylinder operating the tilt having been replaced by a Cat 2 top link. Easy solution is replace it with a...

Let's just say things happened, just can't have nice things and now I need a new bucket curl cylinder for a bobcat ct2025 with the fl7. I'm not sure how to measure to get an aftermarket but if I can figure it out I know it would be about 1/4 the price of bobcat, also my local dealer isn't great...