cut

I am using my new 7' dual spindle RCD1884 to mow springtime fescue pastures. I'm just not getting a smooth, even cut. It's leaving a swatch of partially cut grass in between where the two cutters meet. Has anyone had this problem, and how did you remedy it? I have a 40hp Kubota, running 2500...

lHello all. I am trying to help my neighbor install braces inside her 5"x"5 Pvc fence posts. The issue (there always seems to be one when I offer to help...) is after I dug out all the trash the contractor shoved into each post, I found the bottom rails (ground level) are nowhere near...

Hi all - need some help on the best solution for leveling out about 2 acres of land. My wife and I bought 20 acres a few years ago and had it clear cut in 2022, and decided to leave slash on the ground vs pile it up. We then had 2 acres of it forestry mulched last year around the area we...

I have a large oak tree that the wind blew down along our creek. It’s probably 50 ft or so tall and trunk diameter of near 36 inches. I plan on piecing it out with a chain saw and using my MX5400 to drag the cut pieces out. My question is:due to working along the creek bank I’ll have to use...

Moved to our property in May of 2017. In 2019 my wife and I decided to cut a walking trail around our 45 acres of woods. I started the trail on what I thought was my side of the neighbors barbed wire fence. After looking at my survey a year later I noticed that my neighbors property extends...

I look at the price of new CUTs, and I blanch. I wonder if the price is growing out of reach for more and more first time buyers. Maybe it's that we get locked into what the prices were when we were first interested in CUTs. Maybe I''m just an old fart that says I remember when ... I was...

Finally got around to putting my tire chains on the tractor,now the qustion is how much do I cut off.these are both tires.

gm hope u can help I have a 1944 2 n with 6 volt pos. Ground Issue with cut out..my generator single pole with adjustable brush I need help with installing VR. Asking what VR to buy and how to connect wires THANK U FOR assistance..

Hello, I have a steep, uneven and rocky food plot planted with white clover. It needs mowing once or twice a year. I believe a finish mower may get damaged and a brush hog may not do the job. Any suggestions? Thanks.

Hi all - newbie here. Have about an acre of 3" - 4" Honeysuckle. Anyone know if I can get away with renting a Billy Goat walk behind? I know it will be hard work but I don't mind if the machine can do it. If not, my only other option is rent a Tractor w/ brush cutter but that would cost...

when I am mowing very tall thick reed grass, the tough cut will bog down. It works better if I raise it up (partial or maximum). Any problem with mowing with the deck raised up high on a first pass? Or should I only do that for short distance?

About ready to cut the pin on ears off a WR Long 4n1 bucket to weld on SSQA adapter. The WR Long has a curved back on the bucket, so hard to figure how much to cut. One gent that did this cut those ears off more or less completely, leaving little on the bucket and used them to weld onto his...

I've looked all over and there is no information about whether the Ventrac power rake can be pitched to cut a crown in a driveway, etc. Can anyone confirm if this is possible?

I got a used Spartan SRT-XD 72" last year. I like the mower its self. It has the 36hp Vanguard Big Block that really runs well, and Parker pumps and motors, it will scoot. But the cut is very much lacking. I've put new blades on it, new belt, new idler pully, spacers to lower the blades in the...

Looks like it would be handy for grading slopes or crowning a road...

Hello, I recently found a note on my front gate asking about one of my tractors. I had no intent to sell, but I don't use it much. I talked to the young man over the phone that night and explained the tractor to him. I said I haven't started it for a year. Before that, I hadn't used it for...

I'm not finding much direct comparison between WRLong third functions and OEM kits. I am considering installing it myself (mainly to learn more about maintenance). Both kits are virtually the same price. I'm on a kioti, and the instructions are from what i read - but i care more about...