case-ih dx45

Hey everyone, hoping someone can lend some help. I have a 2007 Case Farmall DX45 with the Shibaura N844L four cylinder diesel. Tractor has about 1200hrs on it, and has started burning oil. It uses about a quart every 4hrs under normal use. Seems to only happen under load and when hot. No...

I purchased my DX45 from a lady who was probably unaware that neither the fuel or temp gauges were working? Anyway I sure would appreciate any advise on how I go about finding the problem so that I can get them both working. The tractor has only 800 hrs on it. Neither gauge will register...

I have a 2007 Case DX45 with factory cab. I went to use the tractor today and the a/c isn't working. Just last weekend it was working as it should. A friend of mine operated the tractor last and apparently forgot to shut down the air and fan before turning off the tractor. I know it said in the...

I have a caseih DX45. I need help with the tachometer connection to the alternator - all the wires are hooked up to the alternator and the instrument panel is relatively new. Does the tach wire run through any relays/fuses, or is it direct to the alt. from the instrument panel? does anyone know...

Full disclosure, I'm new to the tractor owning world, but I have been trying to learn everything I can. My DX45 currently has R4 tires that are spaced 78" outside to outside. It seems a little wide to me, and I would like to get them spaced so that a 72" implement will cover the tracks. It seems...

Hello, I recently purchased a 2007 Case DX45 with factory cab. After doing some deep cleaning on the tractor I noticed that it appears the roof has been taken or torn off at some point. I notice a couple different kinds of silicone and adhesive around where the roof sits on the frame of the...

I have a 2005 case ih dx45. I am having problems with the o-ring at the inline screen of the hydraulics. It keeps blowing a little piece out almost like it is building to much pressure. Some times it lasts an hour or two some times not even that long. I am using the dura ring from the dealer. I...

I have a 2009 DX45 that has been relatively problem-free. A month or so ago I had a FEL hydraulic hose rupture so I replaced the hose and the battery at the same time. First time it started up, the alternator light was on but not full brightness, and the gauges kept jumping and the...

I know this is New Holland forum, but the Case DX45 is same as Hew Holland TC45DA, so...I was looking at buying a used Case DX45 with cab and hydro. Went to test drive it and when I raised the rpm above 1500 rpm or so it started rattling and you could feel the vibration coming thru the hydro...

I know this is New Holland forum, but the Case DX45 is same as Hew Holland TC45DA, so...I was looking at buying a used Case DX45 with cab and hydro. Went to test drive it and when I raised the rpm above 1500 rpm or so it started rattling and you could feel the vibration coming thru the hydro...

I was looking at buying a used Case DX45 with cab and hydro. Went to test drive it and when I raised the rpm above 1500 rpm or so it started rattling and you could feel the vibration coming thru the hydro pedals. Motor seemed to run well and hydro seemed to wok fine, but the rattling/vibration I...

Hi guys. I am looking at a Case DX45. It looks to be in excellent condition but I just found out it has 830 hours. Is that way to much? It seems to be really clean. Any help is appreciated, Thanks, John

I have a Case DX45 with cab and front-end loader. There are 4 hydraulic connections to the front-end loader and no rear remotes. Can I hook up a brush grapple since all 4 lines are used now?

I am looking to buy a repair manual for a DX45. I do not want to pay $300 for it. Does anyone know where a cd or .pdf can be bought? I have searched the net till I have calluses on my fingers with no luck. I bought a manual from Deere for my 4200 for $29.00 on line. There are several listed for...

I have a 2009 Case DX45 with HST, cab, FEL, etc. It has 400 hours on it and has developed a "shimmy" in the 3-point lift. It doesn't matter if the attached implement is super-heavy or not, but when it's raised there will be a slight lowering, then the lift raises, then sinks, then raises. It...

I have a Case IH DX45 with an L350 loader. It has the joystick control for the loader and bucket. When I roll the bucket forward to unload then try to back drag the bucket will just roll back like there is no hydraulic pressure. I have to use the joystick to completely bottom the bucket out...

Have an early 2000s CaseIH dx45 HST that for no good reason will not crank to start. Machine was running well and this happened out of the blue. The seat switch is closed. Lights for glow plugs operation on the dash do not light up. There is no electrical signal to the starter solenoid...

I have a 2009 DX45 with hydrostatic transmission. I'm looking for a box blade to do some smoothing of high spots and some road work. Will the 45 pull a 6' blade, or should I get a 5' one? Thanks

I have a DX45 with the hydrostatic transmission- it's a 2009 with right at 100 hours on it. Taking it to the shop a while back, I drove it 5 miles down the farm/county road and it was incredibly slow. With it in high range and the "rabbit" on it still would only run about 12 miles per hour. Is...

I have a 2009 DX45 with the full cab, etc. set up. When first cranked up and running, the power steering whines when turning the wheel for about the first 10-15 minutes. After that time, it goes away. Is this normal? I took it in for it's first service and it's still doing it...... Another...

I'm afraid to put any more muscle on the control lever than I already have; it's been stuck for about 4 months. Anybody else ever had this problem and solved it without a service call?

I have a new dx45. When I dump the bucket and then try to back blade with it does not stay. I is floppy for lack of a better term. I have to dump the bucket further to tighten it up. Does anybody have this problem. Is this normal for this machine or do I need to get it fixed.

I want to build a cab on my DX45. I have been looking at all the aftermarket cabs out there and they want an arm and leg for them. I decided I could build one for cheaper. I have about 70feet of 1x1x1/8 square stock and some 16ga sheet metal in my garage. I thought this would pry work great. I...

I'm looking for a tractor with FEL with heated and more importantly air conditioned cab in the 40 to 50 horsepower range. Well yesterday I stopped by one of the local Case/IH dealers and looked around. They had the best selection of CUT's with cabs that I've seen so far. They sold Case/IH and...

Sorry for posting in blue - but my red site just doesn't get much traffic :( Getting ready to pull the trigger on a deal I've been working on. Just wondering if I'm forgetting something I might wish I added down the road. Tractor - DX45 w/cab, loader w/quick attach, two rear remotes, loader...

Just looking for opinions on the following deal I've been working on. Trade - used DX33 hydro (2006), LX quick attach loader, mid pto, 290 hours. Purchase - new DX45 w/factory cab, loader w/quick attach and bucket, mid pto, hydro, 2 rear remotes, rear windshield wiper. Price w/trade = $17,100...

Looking to upgrade my DX33 to the larger 45 model. Currently, my 33 just doesn't quite have the power needed for the 72" mm mower, especially in thick or moist grass and I'd also like a larger tractor for some new property we purchased. Here's my question. I'm assuming the 45 would have...

I've been evaluating two different used tractors, both about 2 years old. The first is a JD 4710 with a 460 loader and Cozy Cab. 400 hours. The JD dealer wants $26k. The second tractor is a DX45 with a 116 loader and a Sims cab. 200 hrs. Both have R4 tires. IH dealer wants $22k. Does...

Okay, I was about set on a Kubota L4400 then on a Kubota MX5000 (both manual transmissions) and now am leaning toward an HST. The kubota has a really nice HST with 3 different ranges in the GL4630 and GL5030 models. I checked out the CaseIH DX45 model with the HST and I couldn't really figure...

Does anyone here finish mow with a DX45. I want a fairly large mower to do 5 acres weekly. I was wondering about the weight with the DX45 on the lawn. It should pull a 10 foot finish mower with no problems I would think. I am just cncerned about the weight Nate

I've been all around the block, made a full circle back to these two tractor manufacturers. Obviously the 4320 being a bit larger and more powerful, 4120 is closer in ponies, my thinking of having a bit more HP to move that larger frame around easier. Needless to say, I have RED in my blood and...

I've been all around the block, made a full circle back to these two tractor manufacturers. Obviously the 4320 being a bit larger and more powerful, 4120 is closer in ponies, my thinking of having a bit more HP to move that larger frame around easier. Needless to say, I have RED in my blood and...

<font color="red"> </font> I just got home and unloaded the DX45. Tomarrow it will be put through the paces stump and rock removal for starter. I will take pictures tomarrow guys. Spec list. DX 45 LX 116 FEL Withs ssc ( skid steer coupler) 72" bucket FOPS Bradco 509 backhoe 16" bucket...

A local used eq. place has one for sale and is asking 14,900 for it. Has a new Woods loader and 1300hrs on it and its Hydro to. Hows the price and any word on the on any repairs for Case. I know its very similair to New Holland(same parts) ?