bolt

  1. jigs_n_fixtures

    Bolt on tie downs

    Does anyone know of a manufacturer of bolt on tie down points for TYM tractors? I chock the wheels, and then chain down the axles on my T233 and T293 when I need to trailer them, but it would be easier to tie it down if there were bolt on chain points, which bolt to the frame and have pressed...
  2. jjeff

    Lugnut bolt patterns.

    So a Honda pioneer 500, Yamaha 4 wheelers and sxs's have the same bolt patterns for rims found out recently cuz I dedicate old worn out takeoff tires and rims leaving permanently mounted chains on them for winter use so I just change tires and rims instead of taking chains off and on every...
  3. J

    Head bolt torque sequence

    When I first installed a new head gasket on my YM240D, I was able to find a written specific sequence of head bolt torquing that was very useful. It showed the 3 torque stages, the specific nut sequence for tightening, and the number of re-torques and at what times. Is there such a thing still...
  4. B

    Bolt on forks on a CK20

    I'll need to move a 700# pallet a few times in mid-April and have sourced a loaner set of forks for when I need them, but I'm wondering if that's a reasonable thing to do. Would 700# on 48" forks extended off the loader be likely to deform the bucket? I can't imagine the cutting edge will hurt...
  5. M

    Bolt size/grade

    Ok, I made the mistake and bought bucket skis from VEVOR. Installed on bucket as soon as they arrived, 20 minutes of moving snow, the 3/8" bolts and corresponding nut were trash. Bolt bent, spot welds on nut severed. Not brain surgery skimming snow off driveway, so I'm chalking this up to...
  6. F

    International 444 and similar - rear wheel bolt pattern?

    Edit 7/28/24 - disregard. We got the machine home. If the thread stays consider it historical reference. Does anyone know how to find the dimensions and bolt pattern of the rear wheels on a 444 and similar machine (several series/models should share the same pattern)?
  7. B

    Stripped bolt on fan & pulley transaxle.

    Have a 2013 Bad Boy Zt pro series. The bolt that hold the Transaxle Fan & Pulley is stripped and cannot remove the nut. Can the bolt be replaced ?
  8. B

    I have a 2004 foton 3 cylinder, and a 2006 foton 404 4 cylinder,

    Will the 4 cylinder engine bolt up to the 3 cylinder’s bel housing, the look to share the same bel houses?
  9. F

    U Bolt on Front Axle Super A

    Anybody know where I can purchase the large U Bolt on the Farmall Super A front axle? Thanks
  10. LittleBill21

    Mahindra Max26 WR Long Bolt On Grapple

    Finally finished, barely fit even with their smallest option the Single BOGL, will test it in a bit Used a diverter kit from Artilian.
  11. KilroyJC

    Kubota KX033-4 w/open canopy: stone/bush guard/screen recommendations? Plus boot thread question

    Good Morning! we recently purchased a new KX033-4 with the open canopy (if we wanted the enclosed cab we would have been #852 on the waiting list…). I am getting tired of having to wear my chainsaw helmet while operating so that I don’t get whacked in the face with branches. I have not had...
  12. F

    Stuck knife head bolt — sickle bar cutter

    hey all, my boyfriend just bought a used sickle bar cutter for his tractor. It came installed with a used and in rough shape knife bar , but ALSO came with a second knife bar. He want to removed the damaged one and put on the other one. The problem is that the knife head bolt is stuck … it just...
Top