I traded a MT3 42 for a MT3 57 back in February 24. I a have sixteen hours on the 57 now and it regened already four times. Always does it when I am ready to put it away, so it's another twenty-five minutes of running the engine at 2,200 rpms before it gets done regenning.
The MT3 42 that I...
I want to put a hydraulic top-link on a MT357. I have one from a MT342 that I had but the top-link is too short. I have the Pat's Quick-hitch on the the 57 also.
Anybody have one their MT357? What length did you get?
You will not make any money with the trailer. Everybody thinks you can do it for fuel money if that. Don't lend it out either because when you need it they will tell you that they need at the same time. I don't let my 14,000 lb trailer go without me and my pickup. A $100 minimum for twenty mile...
The MT357 was delivered yesterday. Looks to be the same as the MT342, but has a different front axle and Cat 2 - 3 point. I will have to wait to try the 57 because the is no snow on the ground or in the forecast.
I finally decided to trade my MT342 for a MT357. I needed a little more power when using a 72" front-mount snow-blower. I have close to a forty an half of road to clean out. I believe that the dealer did a very reasonable trade.
The MT342 is like new yet. Only has 128 hrs.
I just talked to TYM Dealer today and told me that every manufacturer that sells in the US has to have tier four emissions from 26HP and up, so I would like to know this stuff comes from?
I called a TYM Dealer today and asked him about a TYM T574 tractor. He told me that they do have tier four emissions. Can not get a mid-mount pto either for a front-mount snow-blower. Have to go with a self-contained snow-blower powered from the rear pto. The cab is also 97.5" high, will not fit...
Check one of your remote valves. I believe it would be the one that has the detent in it. That happened to me this brush hogging. I was just going to unhook the brush cutter and take it to the Dealer. I then noticed that the remote valve was pushed. No more problem.
I have a LS MT342 with 6 Ft front mount blower, At my home driveway that is about an eighty foot horse shoe, the tractor works great, but I have property seven miles from the house and that is about a forty and a half long with a big open field on the north side that likes to drift in. When I...
The problem is this driveway is on some property that is seven miles from the house. I drive the tractor to the property and then back to the house. The driveway is level.
I have a MT342 with the Hyro Transmission. A six foot front-mount snowblower is on it. I have a driveway that is over a quarter mile long to clean out. The Dealer said that the 42 horse would be big enough, but I think that I should have went with the 57 Hp.
I blow with the hydro in the Mid...
I have a MT3 42 and use a front mount 72" snow-blower. I have 1,700' drive-way to clean out. I wish I would have bought the 57 Hp tractor. The 42 Hp does the job but slow.
Ferguson TO-20 parts, engine parts, good head and block, transmission, hydraulics and rear-end and rear wheel centers. Call me with what you need. Sheet-meatal is called for already. Call or text 715-340-72 zero, two.
I took a screw driver between the surface and the speaker and pried gently while unscrewing the screw. There is a nut on the other side that will just spin if you don't give it a little pressure. They must install the speakers at the factory with the cab roof off. To install the new speakers, I...
I want to mount 7.5' Western snow-plow on the bucket of a 530 Ck tractor back-hoe. Can I mount another hydraulic valve off the loader valve to operate the plow angle and when I don't have the snow-plow on I could use it for a hydraulic thumb on the back-hoe. I have a manual thumb now on the...
I would like to by-pass the seat safety switch on my MT342 because when I lift my butt off the seat to see where the forks are, the engine will die. My question is if I take a wire and jump between the switch plug will that work? Will that do anything to the computer?
I was carrying a ramp with the tractor and the chain unhooked. The ramp fell on the top part of the bumper and bent it back far enough so that I couldn't open the hood on the tractor.
I hooked a strap up to the top of the bumper and to my Moline 602 and pulled it back. I was going to add another...
I was carrying a ramp with the tractor and the chain unhooked. The ramp fell on the top part of the bumper and bent it back far enough so that I couldn't open the hood on the tractor.
I hooked a strap up to the top of the bumper and to my Moline 602 and pulled it back. I was going to add another...
I have that problem with my MT342 also. I really notice it when it's in Hi-range, it keeps getting slower. I have 70+ hrs. I will take it in the spring when the roads are free of the salt.
The radio the LS Dealer installed in the cab of the tractor has all the features you could want but you can't see the read out on the screen.
Did anybody install a better radio that you can see what you are doing with the radio with out breaking the bank. I basically want to pair my phone in the...
I have just 59 hours on my MT342. When I have the bucket on the loader and in the air. If I shut the engine off , the loader will start dropping, probably a couple of inches in ten minutes. I told my Dealer about that and that I was disappointed with that. He told me that they all do that. I can...
The blower has LS Emblem, but was made in Canada by Radtach. I mounted a 1-1/2" pipe just ahead of the cutting edge so the blower slides on top of the gravel on the driveway. Blower and the tractor works great.
Yes, I got the loader. I have a seven foot 3 pt. quack-digger, 6' box- blade, 7' back-blade and a 5' brush-hog that I use with my Ford 2000.
I ordered from a Dealer in Central Wi.
I finally got my tractor yesterday, but didn't get the front-mount snow-blower yet. Dealer traded my blower with another dealer for the tractor. Maybe get the blower in 2 or 3 weeks.
I signed the papers today for the MT342HC tractor and 72" front-mount snow-blower. Six to eight weeks to deliver the tractor and not sure about the snow-blower.
I need both left & right side front axle knees and spindles. Maybe even the hubs. The axle knees MUST have the holes for the radius rods. E-mail: koshagrez@gmail.com They must be in good shape!
I need to replace the 2-stage clutch on a 2110 . The reason is that the PTO will not stop with the clutch pushed all the way down. I would change the whole clutch-pac. My question is, can I install the clutch-pac and then just adjust the drive clutch or do I have to do something with the PTO...