Search results

I've got a 15 year old Kioti CK35. Lately the brakes have been sticking on, I've got to pull the brake pedal up with the toe of my boot to fully release them. I've gone over the linkage with WD 40 & inspected for damage, but I've not taken the brakes apart. I guess it's time for a brake job. How...

So I was bush hogging along on my CK35 when I hit a stick about 3 feet long and an inch in diameter. Wouldn't you know it, the stick popped up and went on the right side of the tractor, over the front axle and under the radiator just perfectly enough that it popped the lower radiator hose off...

I have an M7060HDC and have lost the pins in the 3 point telescoping stabilizer bars. I'd like to replace them with some big spring clip pins in stead of the drop-in/cotter pin type that came with it. Anybody know of the diameter/length needed, or even better a source for some pins that'll fit...

I've looked around on the net and all I can find is how to remove and reinstall your existing loader. I can't find much of anything on installing a loader on a tractor that's not "loader ready". I have a 2017 Kubota M7060 mfwd cab tractor and am thinking about adding a loader. The tractor is not...

I've been looking at a 2015 New Holland Workmaster 70, MFWD. Only 715 hours and looks nearly new. It's at a Local JD Dealer and they took it on trade. It has a canopy and 1 set of remotes. No FEL and no FEL prep. Everything, including all the lights, works perfectly as far as I could tell...

As the title says I'm considering a tractor near Grand Rapids MI and would like to hire someone qualified to check it out and give me a report. I live in GA and have a farm in KY, if I end up buying this tractor I'd have it shipped from MI to KY. It's a John Deere 5425, open with canopy & JD...

On 5-22-2008 I posted a thread here titled "CK-35 Arrived!". Members here were very helpful with advise and information which ultimately led to my buying this tractor. I sort of abandoned this site for quite a while as I've only had 1 post in the last 10 years. I thought folks here might enjoy...

I have an old JD 285 lawn tractor with a 2 cyl. Kawasaki water cooled engine. It starts and runs fine except the governor won't "kick-in" when the tractor is under load... or any time for that matter. I can move the governor lever by hand and the engine springs to life as it should so fuel...

Under normal circumstances (running loader, bush-hogging, etc.) my CK-35 runs in the ideal, straight up, heat range. But when I work it hard, most specifically plowing with a spring tooth harrow, although the tractor pulls hard and does the job with ease, it runs right at the high end of the...

Hey all - I've got a CK-35 and I lost one of the pins that holds my 3 pt. sway bars on the tractor. It's the bottom pin - or the one that attaches it on the tractor end. As I remember it, it's about 3/8" diameter and about 3" long with a washer and clip pin. The tractor is 200 miles away at...

It's been a couple months since I posted here about buying a tractor and, with yall's help I ended up with a CK-35 & FEL. I've since added a Bushhog Squealer SQ160 5' cutter & a Bushhog RO600 5' rollover box blade. After using them, these implements seem to be perfectly matched to this...

I have an old JD 165 lawn tractor with a Kawasaki FB460v motor. It'll turn over and is getting gas, but won't fire. Any ideas where to look? Thanks! Dave

I've been looking for a bush hog and a box cutter for my tractor (Kioti CK-35). Found a fellow with a "Squealer" SQ600 5 ft. rotary cutter and RO-600 rollover box blade. Both are Bush Hog brand. I've been able to find a new price for the squealer cutter online - $1250.00 but can't find a...

Right on time. Ben Parson of Eton Tractors in Chatsworth GA delivered it last night about 7:45. He'd put on the tooth bar and rear work light and had everything lubed up and ready to go. He took his time and went over everything on the tractor. Answered a couple questions for me, went over...

For those of you who read my "Kioti buyers, thanks... I think" thread. Y'all have put my concerns at ease and I'm now looking forward to delivery of a CK-35 shuttle, R-4 tires, KL130 loader, & rear work light beginning of next week. I'm dealing with Eton Tractor & Equipment in Chatsworth GA...

I was considering a used 2005 CK-25 tractor. Looks great, low hours, beautiful condition, reasonable asking price for what it is... Problem is, it's got both an old style KL-130 Front End Loader AND a KB-2365 BackHoe. :( After browsing this forum and reading the crack problems with the FEL...