Search results

Kubota Grand L5460 Cab Tractor 4 wheel drive 3 range hydrostatic transmission with 2 speeds in each range Heat & ac; radio; rear defog; rear wiper; front and rear work lights; cruise control and all of the other Kubota bells and whistles. LA1055 Loader with skid steer quick attach Factory 3rd...

Hi. Looking to do some private clearing in a rocky and/or steep area. Invasive brush like Russian olive and dense trees from 1/2 to 6 inches. Does anyone have experience with the Seppi BMS mini fixed tooth mulch head on a midi excavator? Seppi mulch heads in general? Other suggestions for...

So, my son was brushing hogging a field yesterday with the 5460 Grand L and ran over a stump. It ripped off both of the 3rd function hoses in back of the right front tire; pushed up the fuel tank cross over line protection and dented one of the hydraulic filters. Tractor was blowing hydraulic...

Interesting. My hydraulic pressure is 2800 psi at 2000rpm and 2900 psi at 2500 rpm. My previous 5240 HSTC with the same forks and ballast would not pick up a 2000 pound load but Daves does. My 5460 picks up a 2000 pound load but others don't. A little extra hydraulic pressure may be the...

Tractor is a 5460-1 2014 vintage. Loader is LA1055. No modifications. I bought the tractor as a used winter rental from Marshall Machinery with a little over 200 hours.. The loader was originally unable to pick up a round bale with only about 1200 psi at the loader ports. Marshall Machinery...

I have moved pallets of pellets with my 5460. The load with pallet forks was 2400 pounds +. I have heavier duty Michelin R1s on the front, 50% loaded rears and Gannon box blade (1000+ lbs) on the three point. Picked the pallet up flat off dump trailer about two feet off the driveway and moved...

I went from a 5240 that I put 900 hours on to a 5460. I've put 200 hours on the 5460 so far. No problems and regens have been a non-event. The PM (particulate) meter goes up to 100% as you run. When it hits 100% the dash ask to raise rpm if less than 1800 or just goes into regen if above...

What is the intended use? A PTO chipper vs commercial trailed chipper: are very different classes of equipment. I had a lot of big slash cleanup to do and stated with a BX42 with hydraulic feed on my Kubota 5240. It chipped some small stuff ok but I spent a lot of time cutting the slash up to...

Hi Wobblin. I picked up a low hour used 5460 cab this year from Marshall Machinery in PA. It replaced a Kubota 5240 cab. I speced it with R1s (loaded rears), front and rear hydraulics, work lights, rear defog and wiper and radio. I replaced the front tires with Michelin XM27s for increased...

OK, a couple of bad pictures to prove the tractor happened.

Really liked my 5240 HSTC. The loader was strong and the cab comfortable whether plowing in a snowstorm or brush hogging on a 90 degree sunny day. I bought it used and put another 800 hours on it with only normal maintenance. But as the hours built up I started looking for a replacement. I...

The Kubota that is. Some wear but still running well. I'm looking to 2,000. Jim

I'm not sure if this belongs in welding or construction equipment so mods feel free to move. I have a Volvo ECR88, its about 8 tons so in between a compact and full excavator. It has a Geith coupler and I'm installing a Geith pin on hydraulic thumb. The bottom of the thumb is held to the bottom...

I looked at a Volvo ECR88 excavator with a four cylinder Yanmar 60 horsepower engine today. The engine is early emissions so it has a sealed crankcase vent rather than a drip tube. 3100 hours and maintenance looked good. It was stored outside and started up in 30 degree weather with just a...

I have some land in Connecticut that I have been clearing with chainsaw and tractor. I'm looking to speed up clearing a few areas by mulching the smaller stuff. Anyone have leads on mulching in CT and cost? Feel free to email durct158@comcast.net as I haven't been on TBN that much lately...

So the new (to me) tractor is in the garage and I can't tell if the rear wheels (R4) are in the widest position. The centers are dished out, the rim lugs are external to the center and the valve stems are facing in. Can I get more clearance if I move the wheels so the valve stems face out?

I am looking to jump from an open station B (2410) to a Grand L cab. I test drove a 4240 HSTC-3 and the auto up/downshift feature seemed smooth with almost no jump. I drove a used 5240 HSTC-1 and there was a pretty abrupt jump between low and high? Is the shift supposed to be noticeable? Is...