Search results

A little off topic, but I have a nice DeWalt jig saw. Minimal use over the years. The wheel that the blade rides in has broken. Guess which part is the only part that is no longer available. It use to be that you paid good money for a quality tool that would stand up to use. Now I feel they are...

My brothers and I all joke about Dad and "...hold the light....It's in my eyes...". I'm sure in our minds we said hold it yourself. I also learned while holding the light that if someone is doing a job and they are doing a whole lot of swearing , They really don't know what they are doing.

Well , It feels like summer has hit in Central New York. Regarding the sneeze issue, It hasn't happen since I posted the situation. Maybe I was giving it too much fuel on a cold winter start. Thanks for all of your suggestions and comments, Matt.

I went to check my sneeze this morning. I pulled the air intake boot or tube out of its location in front of the radiator so I could see it. I secured a piece of tape over the end so I could see if the flap of tape would be sucked in or would be blown out on the sneeze. Started it up and of...

corrected my first post with warm start no issues.

All warm starts start with no issue. No sneezing. My mistake. I just went out and did some checks. The radiator is full to the top and clean. Checked the oil. Clean , no white milky gunk. So I started the tractor. No sneeze. It is warmer than this morning, mid 30's. This morning was cold. I'll...

No.

Hi Tractor family , I have a 2007 2310 TLB with 655 hours. I have a new issue and/or problem with a cold start. My sequence for starting is push up the throttle up a little bit. Then turn the glow plugs on for 20 seconds, Turn switch to on position for a few seconds to run the fuel pump. Then to...

650 hours on the machine

I'm getting ready to change the fluid in my front axel . Read the book but feel it would be a little easier to fill it thru a bigger opening as opposed to thru the two plugs on top on either end as the book says. My question is how to get the big plastic cap off with out destroying it? Special...

I retired from Verizon in central NY. Way back when , when everyone had a dial tone, I would often get a call to drop off a roll of buried service wire for a new house or someone who wanted to change to a buried wire. We never really cared how it was buried. In fact lot of times we would put the...

Actually , it was a 300 hour service done at 600 hours. At 300 hours I know the front axel was done but at 600 hours I know it was not. The Tech came to the house. So from what I gather here, The steering is part of the of the main hydraulic system. The front axel is separate from the main...

Hi , I have a 2007 MF 2310 TLB. Great Machine. I have a question about the hydraulic fluid. I had the tech come out and do a 300 hour service. Basically fluid and filters. Tech never drained the the front axel, just the transmission. He said it's all connected together. Is there any truth to...

I had a small fimco. Replaced tank. Broke again. Then the pump went. Reused the trailer and hose, got two 5 gallon buckets and got a cheap pump on amazon. I'm happy.

I have 2 Brinleys. I pulled them out of the trash. Went to use the first one and found that the sweepers would not engage. Took it apart and found what was wrong. I called Brinley to order parts. The woman asked where I bought it . I said "Well , I pulled it out of the trash but I really want to...

The stater motor in my 2019 Yamaha 20 hp retails for around $700.00. I only paid around $3800 for it new.

in 2007 I bought my sub compact from a local old school dealer. The same place where my uncle who was a farmer bought his tractor. I was treated like family. Bought a couple implements there too. Since then the owner was looking to retire and the place was bought out by a state wide...

My Father bought a new Ariens back in 1977 . The same year I graduated High school and went in the Navy. So he lost his snow shoveler. I believe the Ariens is a is An 8 hp 32inch cut. I am 62 now and am using the the same snowblower to my driveway. It is a beast! I do routine maintenance along...

Unimog

I got it off. I read deeper into tractor by net. 3 inch 1/4 20 screws in the holes. nuts underneath the steering wheel, snug it up, applied some torque and off it came. I did keep the nut on the shaft so I wouldn't damage the threads.

Quick question. How do I pull the steering wheel off? I have a fly wheel puller for outboard motors that matches up, How ever, the 3 holes in the steering wheel is just plastic. What kind of screws am I using to screw into the steering wheel to pull it off the shaft? As far as the bushing, I...

dryer sheets

In high school, 76-77, I walked to school with books in one hand, shot gun in the other. I was in Rifle Club. Some kids brought their shot guns on the bus. We would put them in the trunk of the driver ed car. After school we would shuttle over to the local sportmans club to shoot clays. Fast...

I have a 2007 Massey 2310TLB. I love it. It is solid. I have dug out a bunch of stumps with it. How ever, If I looked at the same Massey today , I would walk away from it. It looks like it was built by MTD. It is like how cheap can they make it.

I have an ECHO bear cat self feed , I mean yourself feed. Great for home owner use.

Thank God for the Phone Company. When I worked there , I also took all my used oil there.

I have a Massey GC2310 TLB with a 2350 FEL I bought in 2007. Love It. I am looking to put a 4' snow pusher on it but I see all the snow buckets are of the skid steer quick attach type. Has anyone put a SSQA on there 2350 FEL? I am going nuts trying to find one for the 2350 FEL. I need your...

Just want to add my 2 cents on my chipper. I have an Echo /Bearcat 45540 PTO chipper.I purchased this model because I felt as though it would meet my needs. And it does.I have it hooked up to a Massey Fugerson 2310 TLB. I fit into the Home owner occasional use category. Two things I liked about...

Hi all, I have a Sears Craftsman GT 3000 (917.275042) with a 23 hp Kohler. I have a steering problem where I can make a real sharp left turn , but my full right turns are real wide. I can't find any adjustment to center the tires when the steering wheel is in the center (straight) position...