Search results

My DK4710se is in the shop getting a new set of bushings for the hinge where it attaches at the back of the dash. This is the third for my tractor. This seems like a low stress part to keep having trouble with. Anyone else had any trouble.

The suspension section broke while I was doing some bushogging. I need to get a replacement. What is considered the best for the money. The factory seat was almost $1500. I am sure I can do better.

This looks interesting. Has anybody tried them. It looks like quite a deal. https://www.crossfilters.com/products/cfkit-maintenance-filter-kit-for-kioti-tractors-ck3510-ck4010-hst?variant=37963122868414

I drove by my local JD dealer and he has a lot full of new tractors. I drove my Kioti to the dealer for some service and his lot was full as well. He had a stack of tractors out back that were ready to assemble and zero turns are far as the eye could see.

My 3 year old Brushbull has picked up a good bit of vibration as the RPMs go up. I have checked the PTO shaft and blades and they seem OK. I found that one of the bolts holding down the gearbox was not tight, but I took care of that. I suspected that Maybe I bent an output shaft. I have run...

I am noticing some vibration that I can feel in the steering wheel. It seems to come and go or at least is more intense at different RPMs. I have checked the blades, but seem to look OK. The stump jumper has a couple small dents, but nothing major. I am beginning to think that maybe I have a...

Lost my gas cap the other day. I guess it twisted off while dealing with some brush. The local dealer did not have one so I grabbed a universal one at the auto parts store. It had to go to the dealer for another issue the next day. They claimed it is slow to start now and is showing a code...

The hood on my 4710 failed to shut after a radiator cleaning. Looks like two broken bushing mounts and a bent hydraulic support cylinder. The good news is my warranty ended the middle of June.

Have been using a 220 volt 170 amp cheap Mig welder without much success. I am looking to upgrade. I can't really justify the price of a Miller even though I know they are very well respected. Is there anything in the sub $700 range that will work for farm equipment.

Thinking about hydraulic top link. I am getting mixed answers. Do I need a check valve? I see them sold both ways. What is the quick coupler I need on the hoses. I think it is a 1/2 inch pioneer male. It is going on a Kioti 4710SE.

Anybody tried the top link sold on E-bay? Seems to be only one guy selling almost all of them . Looks like I can get it shipped with 2 hoses but no quick attach couplers for $210. It seems like a good price.

I keep a generator in the truck to power tools and to run an air compressor. Time for a new one. I need one that will handle a 12 amp compressor and i would like for it to be manageable if possible. My old one was too big so it took up a ton of room and was a bear to move or unload. What do you...

I have found two almost new bushogs for sale.One is a Woods Brushbull that is about one year old,the other is a Bushog Squealer that is maybe 3 years old but looks new. I like both and the cost and location are about even. Which one do I want and why?

I bent my loader a bit and am going to have to work on it a little. I have a few questions. How best to straighten the bottom of my loader. It is bent in a bit of a frown. I suspect it is not quit 1.5 inches. I have a tooth bar that protects against this but I need to take it off from time to...

Came on yesterday. I drained the filter. Is that all I need to do? The filter only has about 40 hours on it.

I bought a Kioti 4710 last year and did not use the tiller behind it until the other day. I got it on but it was by no means quick and I suspect removing it will be difficult also. I am using a HF quick hitch and have managed to make it work with everything else. The tiller is a 5 foot King...

Not a tractor but here it goes. Replacing the belt on my zero turn. The pulleys are all free spinning and the belt is the correct length but it does not seem to fit properly. The belt seems an inch or two too short. The idler pulley does not return to the same position as it did with the old...

Sometimes I have zero problems, other times it is almost impossible to hook up. I know how to release the female side but the only way I know for the male end is to unscrew the cylinder coupler and let out a bit of fluid. There has to be an easier way.

I just had my first service on my DK4710SE and it was over $500. The hydro filter alone was $136. I guess I will do the next one myself. Anyone have cross reference #s??.

I am having all kinds of problems keeping my radiator clear. Been using a leaf blower but it is not getting it all out. It would be nice to have compressed air. I could load up my generator and compressor but that is a pain. Will a full 11 gallon tank hold enough air to be useful?

Anyone put an outlet on their tractor. I have a DK4710 and am unsure the best location.

I used to always mow with my FEL on. It took the punishment and did it without issue. My new tractor is larger so it is harder to haul and mow with the loader on. I have a grill guard but it is not enough. I am thinking of a drop down bumper that protects the battery box,steering rods and the...

I thought I understood this but I recently have gotten some different views. My truck has plenty of romm but my trailer is close when loaded. Do you subtract tongue weight from the total load as it is being carried by the to vehicle. EXample- 7000lb GVWR 2000 lb trailer +5500lb load =7500...

Drove it today. Very nice. Salesman is pushing me toward the 4710 because of cheap HP(less than $1000). I just need to be able to pull a 6 but bushog without bogging. It has over 29 pto HP. Anyone have one? What do I need. I would like to know the weight of one with R$ tires if you know.

My Bobcat tractor has been giving me some tough love so I am considering a replacement. Here is what I have looked at LS XG3135 $17900 LS xg3140 $18,900 TYM t394hst $19,500 TYM354hst $20,999 Kubota3301hst $20,490 NH...

I have my 225 back in the shop for a front end rebuild. I just got it out after having a new seal in the front hub replaced. this will run about $3500. My other repairs have been 2 new front hubs $1300 each repair 3 hydraulic leaks $2300. rebuild motor $3000 trace down broken wire that kept it...

I have a leak in my hydro system on my CT225. I need to top it off from time to time. Does anyone know the amount needed when it reaches the low mark? It is more than a quart.

Not sure what I need or how to mount. I guess It would need to be portable so I can pull in both directions. I am looking to avoid that once a year wrecker call that usually takes a couple hours and cost about $150.

My 20 car hauler needs a bit of work. The inner fenders have come loose. They are just spot welded to the side of the trailer and the inside of the fender. I tried to weld it back,but had to use caution to not burn through the thin sheet metal.It did not hold. I am a poor welder and I know it...

I left the cap off the end of my can when I filled it up. It has rained over 2 inches this past weekend. Do you think enough got down a 5/8 tube into 5 gallons of fuel to worry about?

What is the size of the grease zerks on the bottom of a Bobcat CT ?

I saw something post about every week for quite a long time but I don't remember the last time i saw anything on the brand. I thought they were going on a push to add new dealers. KY has the same ones and no more. Have Yanmar and TYM sucked up all the oxygen or is something else going on?

I seem to pop a hose every year or two and have always gotten a new one from the local tractor dealer. They were out of fittings the other day so I went up the road to NAPA and gave them a try. $57 dollars later I had a new hose for exactly twice what I had paid at the dealer last time. Where do...

I was looking at the Kioti site and the CK27 shows 28 HP and 20.5 pto. I thought we had the same engine. I actually thought it was the same tractor. Whats up?

The gearbox became a bit loose and it cracked the plate slightly around one of the holes on the mounting plate. I need to repair. 1-Take off gearbox and cut out the plate and replace. 2-take off gearbox and mount a 1/4" plate on top 3-weld a plate over the cracked area What would you guys do?

Need a rattle can for some touch ups. Dealer wants $12+ a can. Are there any alternatives.

My wheels are starting to look faded. What is the best, economical way to repaint?

Will any of these tractors run a 5 foot rotary mower. I know they are detuned engines for the most part. I suspect the hp figures might not be totally accurate.

I see less and less in my country. Years ago, they were #2 behind ford in my area. I never hear any complaints from owners. They look to be well built. Am I missing something?

All of us Bobcat tractor owners realize that our tractors are orphans. I very much like the forum and check the Bobcat threads every day or so. I always see several others viewing as well. I also see that we are one of the few that have their own category, but are no longer supported by the...

I just had to replace two tires on my trailer. They were 205-75-r15 and all my usual local dealers were wanting about $85-90 each. I did a little looking and Wal-Mart came out the cheapest by far. They are China tires but they were only $44 each +tax. This was shipped to me and if I took the...

When you change your oil, you can tell a difference between the used oil and new oil. I don,t really see the difference when changing hydo fluid. It is the same viscosity,color and looks nearly the same. Is it the same for you guys?

Yanmar has a good name and the work they have done for John Deere should help. They have been around as a supplier but have never made much of an impact. I thought they might succeed when they partnered with Cub Cadet but it failed. Bad timing I suspect. Do you think they can make a go of it...

I am hearing more and more about the dangers of the chemical agent in Round-Up. I use it quite a bit both at work and home. Any thoughts?

I have several that won't take grease. Planning to replace. Anyone know the size?

Got a lead on a used mower. It is a Bushog brand 5 foot mower. It looks a bit like the Rebel series but is built a bit heavier. It has been stored indoors and not used much even though it is at least 25 years old. I have never used a square back. What is the general opinion on them

I leave my loader on. I took it off for a repair and struggled to get it back on. I have no problem with the lower bracket but the way that the top bracket must capture the top pin requires it to come in at a set level. when I used the dump function like I have done with other loaders, it tended...

My 225 is back up and running. It seems slightly stronger than before. The total price with labor and parts came in at $3100 with 6 month warranty. Tough lick but could have been worse. We will see how it goes when I put it to work.

As many of you know I am in the middle of an engine rebuild and have the tractor in half. I thought I would see if I could dry up a hydo leak I have had for 2-3 years.It only showed up when the motor was warm and was barely visible after it cooled off. It seems to be close the to output shat...

Anyone done it? How did it turn out?

I want one! Altoz TRX - World's First Zero-Turn Track Mower - YouTube

I have a Bobcat ct225 which is a twin of the Kioti. I have a damaged engine and am looking at a rebuild. I have a few questions. Does it use the same block? Can I overbore to the same size as a 35hp or does it have a different stroke as well? If the answer is yes, what problems if any do you...

Was mowing horse pasture that was a bit high but not overgrown since I mowed it in mid summer. I smelled oil so I got off to investigate. A 3 foot branch had speared my oil filter and bent the canister just enough to allow the oil to leak out. I was not really alarmed ,since did not appear to be...

Was doing some Bushogging when a stick hit just right and hit the oil filter. it was a few minutes before I smelled the oil and shut it down. Put on a new filter and added a gallon of oil. It brought it to full so it was not completely dry. I ran it about 10 min. but shut it down due to pecking...

I usually use short chains through the stake pockets that attach with a clevis to the end of the tie down strap. It is a shame that the hook will not drop down through the pocket like a log chain will. There has yo be an easier way. How do you guys who use straps do it?

My john Deere zero turn was stolen this week. I am looking to replace it with something a bit cheaper and not have to overcome that $1000 deductible.I don't use a finish mower every day. I mow some lots for some builders so they can be on the rough side.Ability to cut higher grass and hold up is...

posting error

posting error

My john Deere zero turn was stolen this week. I am looking to replace it with something a bit cheaper and not have to overcome that $1000 deductible.I don't use a finish mower every day. I mow some lots for some builders so they can be on the rough side.Ability to cut higher grass and hold up is...

I have a leak behind the dash where the hose connects. It looks like a straight forward replacement. Anything tricky about it? Second question. Am I better off waiting a couple of days for the OEM replacement hose or will I be OK just taking it off and getting a replacement made locally?

I was told that since the capacities of the new trucks have increased, a CDL is required for any truck whose weight and payload exceed 10,000lbs. I asked a second person and they said that was correct and that is why you see a lot less dualies these days. Is this true?

I just picked up a new rotary cutter, or at least, new to me. It is a Hawkline five footer. It is a little longer than the cutters I have had previous to this. It has a single tube tail wheel assembly rather than the a-frame type that I am used to. It sticks out about 18" behind the rear of the...

I have a ct225 and hit a curb with the front tire the other day. I was running the tire a bit low on air and it bent the outside rim a bit. It now has a slow leak. Can I straighten it or am I going to be looking for a new wheel?Anybody know what a new wheel cost?

A lot of knowledge on this forum on how to get stuff done. I think info about the best tool for the job and a better way to use it would be handy.

got 6+ years out of it. Great in my book. Went to rural King and picked up a mid grade Exide battery for $49.95. The bad news is that the bolt haeds to the battery hold down had rusted where the live under wet seed and leaves for weeks at a time. Had to remove the grill to gain access with a...

Saw it on my way to Myrtle Beach. I was passing through Florence South Carolina and decided to check it out.I have ended up at the website more than a few times. The block and mortar place is huge and seems to have everything. Must be 100,000 square feet in the main building. It took me 20...

Been a good mower but one side is pulling weakly on the left side. It has a bit of chattering as well when you are going up hill. It has separate pumps and wheel motors. What is the most likely problem? Dropped a # in my header it is a JD model m665 sorry

Pump went out day before vacation. Trying to set aside some $$. Any ideas ?

I broke one of the lift arms on my 5 foot king kutter rotary mower. It broke were the lift pin goes through. Can I grind and weld the lift arm, then weld and drill a plate to reinforce the arm. It will require a longer lift pin. Am I wasting my time and should go ahead and buy a new one?

I have a ct225 and use it quite a bit. I have 1050 hours on mine. Just wondering how the rest of you guys are doing.

I noticed that one of my wheels on my trailer is suffering from a bit of toe out. I suspect I hit a culvert or something. My friend said he had you can bend the axle pretty easily with a chain and a jack, but has never done it. Anyone have any experience with this. I am interested in giving it...

If I run my tractor till it is really low on fuel, the gauge sticks. If I remove the sending unit. It just pops loose and acts fine. It works fine until the next time. Any ideas.

Mine is going on 5 years old and is still going strong. It seems a s strong as day one. Anybody hit the wall yet?

Key turns on tractor and operates dash lights but does not turn it off. Does it have a kill switch?

I have a compact tractor and do a good bit of contract bushogging so I am never sure what i am going to run into. I have had Bobcat and Titan front tires in the past. I got a good deal on some Carlile's and I sure am disappointed. I have had flats in years gone by, but always from a piece of...

Dropped front of tractor in a small rock filled ditch a month ago. Was able to push myself out with the loader. No harm done ? A week later fluid is running out of front hub. Local dealer replaced bearings and axle to the tune of $1100. Friday, I was mowing when I went around a turn and the...

I noticed that my cutter was not working properly so I took the blade carrier off and took a look. All the splines on the carrier were worn. I looked up a new carrier and noticed that the hub is replaceable. They say weld in. I am guessing you grind off the weld and press it out. Anyone done it...

My ct225 has a fluid leak that is going to require splitting the tractor to replace a seal. Bobcat quoted me 20 hours labor plus parts. At $92 per hour, I will be getting close to $2000 for the repair. I know it is a big job, but this seems like a bit much. What do you guys think?

Need some for my tractor.Looking at Titan from simple Tire. What other brands should I look at? Looks like about $145 delivered.Anyone have a better source. I have given up locally. I was getting prices of about $200 each.

John Deere M Trying to sell old tractor for M.I.L. It is a JD series M that was made about 1950. It is not running but is in decent shape other than dry rotted tires and need for a new seat. What should I ask for such a beast? Tractor House was not a lot of help. anybody sold one or looked to buy?

I know it's an older mower, but it is priced right and has less than 600 hours. Whats the word on this model?

As the owner of a Bobcat compact tractor, I know they are no longer available. Montana is history. Century I think has transitioned to Branson maybe ? Any other companies started or stopped in the last couple of years?

This was linked on Yahoo yesterday Ford f250 was #1( I am working from memory but it think it was 4.1 percent) The only car in the top ten was the Honda Accord at #10

Anyone had any problems?

Thinking about trading. Looking for new tractors with AWD, loader,hydro and about 30hp. What is the best deal these days. I don" think I want Chinese, but anything else is worth a look.

I am starting to see some LS tractors in my area. It looked like Masey F. a couple years ago but they have fallen off.Kubota and J.D. have most of the market around here.

Getting next to impossible to find air in my area. Truck stop had hose at all the truck pumps until recently. Put in vending machine air which is slow and expensive if you need air in more than one tire. I find these machines at some of the fuel stations, but most don't work or are stuck in a...

I mow building lots and mostly I use a rotary mower to do the job. About 25 percent could be done with a strong zero turn. That would save wear and tear on truck, trailer and save gas pulling that heavy tractor around. I would also be able to get rid of my home mower and be able to move the new...

I need a set. Size 25-8.50-14 commercial tread.. They are running about $175 locally for each tire plus install of about $15.Bobcat wants about 2 bills for each tire. The last set I got a little less than 2 years ago and paid about $225 for both. I know tires have gone up but this seems a bit much.

Lower seal in rotary cutter gearbox I have always, in the past,went the grease route when a leak started, but I have to remove the stump jumper in order to remove some wire. I think I will just replace the seal while I am at it. Any tips?

I managed to lose the sleeve part of what I call the sway bars for the 3 point arm. It is the arm that controls horizontal movement of the lower 3 point arms. I called to order a new one and they can't seem to find it. Any idea what bobcat calls it so they can look it up? I tried stabilizer as...

Had tractor in to have hydro tube replaced and after getting it back my travel pedal is not operating properly. Crawls forward with foot off pedal and will not start without playing with the pedal to get the safety switch to close. Is there an adjustment?

Broke the output shaft on my IM500 cutter today. Do I replace the shaft or just get a new gearbox? Agri supply has the best price I can find. They are about $120 + shipping. anybody tried one? Will they be able to cross reference it or will they need gearbox #? I think the part # is tx4-740...

In the market for a new work truck. Found a Dodge 2500 club cab 4x4 with a 5.7 v8 in it. It has auto trans, and is clocking about 100k. I think I can get it for about $8500. What is the deal on this setup. What to look for? Anything to avoid? It is a 2005 model.

I just heard a couple new twist on D.O.T. regulations. Not sure if they are correct or not. 1. D.O.T. # on vehicle must now include name of business 2. Fire extinguisher must be mounted in cab of tow vehicle. 3. Every item on trailer AND in truck bed must be secured at all times.This includes...

Pulse brakes stopped working from the pedal last week. I can still get them to engage if I use the slide on the controller. The controller is less than a year old so my first thought was not that it was bad, but what else can it be?

Just got the new Car and Driver. They gave it a quick review. It looks pretty good. 305hp v6,8 speed trany,air adjustable ride, new interior and 18mpg city and 25mpg hwy. This all at about the same prices a last year. It looks like a very good combination. I am interested to see a real world review.

Not sure best way to do it. Here is what I have Tractor with loader and toothbar potato plow(middle buster) box blade quick spade for loader I just need it underground an inch or so so the ground is level. No heavy equipment will go over it. It is just on top of the ground right know from...

Needs a new tractor. Wants 4wd 40-50 hp utility with a loader. Brand not super important. Whats out there that he needs to look at? Any good deals? Anything to avoid?

I have a couple of fittings that are not taking grease. I plan on replacing them. What is the thread size?

I just replaced the front tires on my c225. I got 540 pretty tough hours out of them. Anyone else done it yet? I scored and found some blems on Ebay for $95 each shipped. Bobcat was about $190 each and they were cheaper than anyone else.

I just traded for a car hauler. It is Gatormade brand. It uses a 205-75-15 tire and a 5 lug wheel. Anyone know the wheel spacing? I need a spare.

I just traded for an 18" car hauler that has pretty standard flip up ramps. They are locked in vertical position by a piece of 2" flat stock that is pinned to both the ramps and the side of the trailer. I don't like it much. It seems to take 3 hands to get everything lined up.The flat stock...

Tractor runs hot in about 30 min of hard use. I have been running a rotary cutter a lot and I know it puts a lot of debris in the system.I clean the screen often and blow and wash the radiator when I get home. Plenty of coolant and the fan is working. I still feel like I am not getting enough...

What is the trick. I am getting tired of running on the edge. How do you keep your tractor cool? I alternate rinsing out the radiator, brushing the debris screen and removing the screen and blowing it off when I have access to air. I was in some high stuff(bushog) and could only go about 30 min...

I haul about 4500lbs on a landscape trailer with two 3500lb axles. I seem like I am always replacing a tire due to wear. They all seem to wear about the same, I doubt I get 2500 miles out of one before it is time to replace. Is my wear about normal?

D.O.T. has gotten serious on utility trailers in the state. Up until now, almost nobody had a license. Not anymore. My problem is I bought my trailer with cash off craigslist several years ago. I got trailer and no paperwork. I now need to get things legal. They are telling me to apply for...

My old drill press needs a new pulley which I can't find, so I am in the market for a new one. The two I am looking at are Black Bull (T. Supply) $139 on B Friday or H.Freight. $191 using coupon. Which is better? Is there another option <$200?

I need one to put on the back of the truck(hitch) for big jobs. I have had no luck with Craigslist or flea markets. Where can I get one that is sturdy, I can handle getting it off the truck by myself(under 75lbs) and will not break the bank?

I keep hearing that The tractor thing is not working for Bobcat, but my dealer says otherwise, and has plenty of inventory. What are you guys hearing? I don't give it much, but I don't know the whole picture.:cool:

I saw the show last night. Super Duty 450,Ram and Chevy H.D. Not really a clear winner. All were pretty good. They gave it to the Chevy with a laugh. Ford pulled down two telephone poles Chevy pulled train engine and one car Ram pulled down a house

It is driving me crazy. I fave tried mowing slow, holding up discharge chute and making sure the blades are sharp. It won't mow 3" grass if it is not totally dry. it clogs up in the deck and discharges in clumps, if at all. Anyone have any suggestions? I am afraid it is just a poorly designed deck.

I need a plug in the garage for my 220 welder. I was hoping to share the 220 coming in for the water heater. The first problem is, how to get around the WH coming on while I am welding and overloading the circuit.I am thinking that I run hot to the welding plug then branch off with a switch on...

I bent the A-arms on my King Kutter mower. They are twisted a bit and pulled toward the back of the tractor. This limits the amount I can pick up the cutter for transport. How do I bend it back into shape and reinforce it, so it will stay that way. I am a bit concerned the bolts will not line up...

I just brought my tractor back after the forth time to the shop for a leak. They have been great about it , but I am a bit concerned. The leak is around the rod entrance for the shifter. They said it had 2 o-rings on it and that may have been the problem, but Bobcat info only shows one. They...

Looks like I need new brakes on my 7500lb landscape trailer. I opened them up and they were stuck and rusted. I ordered new brake assemblies. They look pretty simple to put on. 4 bolts and 2 wires each. Any tips?

My neighbor got a great deal on a 5x8 utility trailer. He was planning on using it to haul his subcompact tractor with a 60" mowing deck. He has a 18' tag-a-long he had been using but it is overkill. We were thinking about risers for the wheels to run on which would pick it up enough to clear...

I dropped a bucket tooth on my gate and ripped two fist sized holes in it. How do I go about repairing it?

I saw one the other day. I liked it quite a bit. Well built deck and tail wheel as well as replaceable skids. I could not find anything about it. Nothing on the internet. It said it was made by Walton, but that was no help. The funny thing is that it seems to be a copy of a Kodiak. The model...

Went out to a guys house to level a spot for a portable outbuilding. I should have known how it was going to end up when he gave me wrong directions to his house, twice. I got there only to find a pretty flat area to start with. He had not called for underground utilities , so I said I was only...

I am about to the end of my warranty and have been pretty satisfied. I do have a lingering fluid leak that has been difficult to totally stop. I use my tractor to make $$ so it would be a comfort to have a warranty to fall back on even if it cost a bit. Is this an option?

I ran the 225 until it was almost out of fuel, when I filled it up the next day, I got nothing. I thought it would start working as the day went on ,but nothing. I have to believe it is a stuck sensor. What do I do?

I need one to leave in my truck. I always need to clean up after a job. I don't want an expensive one because I am always having things roll over on stuff and knobs and plastic pieces have a tough life.

My neighbor was unloading his new Holland 2600 from his trailer while it was backed down his driveway. He did not chock the wheels or support the rear of the trailer. When the tractor got about 1/2 way off, the front of the trailer raised the rear of the truck off from the ground. Down the...

I ended up with a Big Bee 5' rotary cutter(ld 540 I believe) as part of a deal. I have decided to keep it as a spare. It has a new gearbox on it and the sides are fine,The trailing wheel is OK, but not HD by any means. but the A-frame is bent slightly and the sheet metal is rusting. My neighbor...

I have some chain on forks that I use way more than I thought I would. I am going to mount a receiver on top of the bucket. How could I use it to secure the forks? I am up for a little welding if anyone has a bright idea.

Propane weed burner claims 3000 degrees and looks like it puts out a pretty impressive flame. Would this supply enough heat as to be helpful bending metal?

I have all of my other stuff on dollies and it makes them way easier to store and hook up. I still don't have a working one for my Bushog. I tried to put furniture dollies under the front and let the rear wheel support the rest. It was very hard to turn and move. it also wanted to slip on the...

I just bought a used KK tiller and I am having trouble adjusting the depth. Looking at it from the tractor seat, the depth skid does not seem to line up in the bottom hole due to the gear case. I can get the right side to about 6" but am limited to about 3-4 on the left side. The holes just do...

I scored on Craigslist last week. Tiller,harrows,plow,carry-all,Bushog and boom for $1500. I was feeling pretty good until my neighbor called me today and said he needed some help. He just bought a sweet 2600 Ford with harrows,plows,grader blade,carry-all and a almost new PH digger-$2000:p

Lug nuts worked loose on my right rear. I tightened them and limped home but the damage had been done. The holes were double the size they should have been. I have a friend that is a hoss cat welder and he filled up the holes. it looks very good even though it is aluminum. It is my plan to grind...

I bought a used tiller and it is missing the spring loaded detent pin that you push when you put the shaft on the PTO spline. It looks like it is held in by a rolled pin. What is the name of the part I need. I can't find anything.

Time to try another brand. I have an old weed eater that still runs. I find I end up using it because I can't get my Stihl started. This is the second one and neither were reliable. I have a chainsaw that is bulletproof. Husky,Echo and Shindaiwa are sold in my area. What are you guys using?

Just did my taxes. All my equipment has depreciated out. I am thinking about buying a tiller for this year. It seems like about $1700 is the going rate for a 60" tiller. I could live with a 48" if the price was right. What is the best deal out there right now?

My tractor lives outside. I am having trouble with the lock set freezing. It keeps the key out so I can't start it till I apply heat. I need to cover it with something that keeps out the water. What do you guys use? The tractor is a Bobcat ct225.

It did not work when I fired it up the other day. It was low on fuel, so I thought it might respond to a fill up. I got nothing. Guess what. I ran out of fuel that day. I got to get it fixed. any ideas?

I saw this and seems like a decent idea. TURBO-TILLER

I have had a bit of a leak for a month or two. I took it in and the rear gasket was replaced. We all thought that was the fix. Got it back and no change. Took it back for another look. They looked a little closer and they think they have found the problem. I have a cracked transmission housing...

I was a the dealer the other day for a repair and I was ask if i needed service. I said I only had about 125 hours and was not due another major service until 200(50 hour was done). He told me that for maximum performance, they thought that 50 hours was the proper service interval. I still can't...

Had some problems with tire wear. I checked it out and it looks like my front axle is bent near one wheel so I plan to replace it(3500lb idler straight axle). Where do you suggest. I plan on getting one with hubs on it so I'll be ready to go. Looks like $250 locally and about $100 less on line...

I have been having leakage near my PTO shaft for a couple of months. I took it in and they put a new seal on the back plate. I guess that was not it. Still leaking, I can't do without it right now. Too busy. Maybe they will get it second time around.I know slow leaks can be tough to find...

I am a cap guy so a hat seems a bit much, but my girls thought I needed a wide brimmed hat to protect me from the sun. They got me a Tilly Air-Flow for Fathers day. I think they gave a small fortune for it. I hate to admit it, but I love it more each time I wear it. Fits different and feels...

In the summer heat, you got to have some water. I struggle to find a place on the tractor for a water jug. I have a cupholder but it is useless. What do you guys do?

I am always amazed when I go to get an oil filter. Why do you need 50 different sizes? Why don't they just standardize it by engine size? Break it at each liter engine size and you are at less than ten. Let one cover a 2 liter range and you have 4 or 5. Know your engine size and you know your...

I am not sure when I did it as I have not done anything rough that I remember but I have twisted the A arms on the three point attachment on my King Kutter mower. They are not bent a great deal but it moves my top attachment point forward about 2". That cost me about a foot or more in lift ant...

I am happy to report that I have just passed the 100 hour mark and my ct225 is getting more powerful every day. I just finished brush mowing a small horse farm. It was very level but the grass was thick. I did most of it in high range. When I first got it, it would barely take off in high, much...

My friend has a small shop and I can get big stuff welded. I hate to bother him for the little stuff. I need a small welder for the little jobs. I think a flux core or MIG would be best. This will be for small jobs and infrequent use. I have my share of Harbor Freight stuff but am scared of...

I did not know of the store until a couple of years ago. I assume they sell imported stuff for the most part. I won't be buying a loader or a Bushog from them, but their prices on simple stuff seems incredible. I can buy a landscape rake, carry-all,chain harrow,cultivator and a boom for less...

I have been doing some work and not happy with the end results. I hire out for small grading jobs,driveways and some reseeding along with some loader work with gravel and topsoil. I need something to finish off some of this and get a groomed look. I am thinking a chain harrow might be the...

Tired of the tiny one. I need a replacement. Where did you guys find a weatherproof toolbox?

I am getting around to finishing the 50 hour service. I have done it in steps. changing the hydro and filters is all that is left. Any tip? Anything to watch out for? What did you use to drain all that fluid in?

Just a heads up.This has happened to me twice. It has brought things to a screaming halt. If you are doing loader work in high weeds, you can get debris in the safety switch located under the frame below the seat. I have twice had a leaf the size of a fingernail keep the tractor from restarting...

I am using my box blade more and more. I have recently been getting work busting up existing gardens with the rippers before I hit it with a walk behind tiller or the landowner finishes it off. It takes several passes, but does a pretty good job. I am thinking about cutting a couple of ripper...

Anyone came up with any good solutions to unloading bulk items from a non dump landscape trailer? I am thinking along the lines of pulling it off on tarps with the tractor, so I can get to it with the loader.

I was coming back from a few days in Pigeon Forge, Tenn. when I saw one of those great loading jobs. I would have loved a photo, but I was not quick enough. I saw an R.V. pulling a car hauler. A late model Tahoe was on the trailer. It was secured on all four corners with a 1" wide camo...

Which way do you load your tractor? I have done it both ways and I have about decided It is easier to drive it on and back it off. My O.M. recommends backwards but does not say why.

I got the perfect job today. A guy called me to level out his back yard. He said it looked pretty bad. I got there and it was a large load of topsoil with some trash thrown on top with grass growing wild. Took about ten minutes to clean up the trash. The rest was about as good as it gets. I...

I spent weeks agonizing about buying a tiller for the back of my tractor. I just could not seem to make the #s work out where I could make any money. I stepped back and thought about it. I need a tiller but not a 3 point tractor tiller. I bought a big rear tine with reversible tines and made...

I have been doing some garden plowing with my tractor, but I only have a walk behind tiller,so the big gardens took some time. I needed a way to smooth it out before I brought in the tiller. The only one I have access to was an old drag type that is a bear to transport. I was just going to use a...

Got to get one and can't wait for used. Buying cash and my limit is $1000. Is there any difference or just buy by price?

I have thought about making a longer middle arm on my box blade instead of buying a separate machine for the few times a year I might need it. The only downside is shear protection. Any Ideas?

I do some tractor work but it's just grading spreading and some bush mowing. I'm getting calls wanting to know if I till gardens. I am considering buying one but it's tough to justify. Looks like about $1500 for new or $900-1000 for good used. At $50 a garden it will take a long time to get to...

Any idea who makes it? Is it as good or better than The Warren automotive that I seem to find most everywhere (Coastal,Mystic,Carquest,Advance Auto and TSC)?

I am finished with my 50 hour service except for changing the hydraulics. I don't think I can pay Bobcat prices. Anyone using anything else? I am considering Sam's Club UTF,Tractor supply UTF, or coastal UTF. They all are about 1\3 the price of the Bobcat product. I keep hearing that it is...

I park my tractor on my trailer (18 foot) to save space. I have room for the tractor to come off if need be. Is there a safe way to do this without hooking it to the hitch on the truck? I could not get my truck to the trailer to unload so I could clear snow from my driveway I have thought about...

This is pretty cool. I feel like one of the big boys now.

I just traded trucks and it has duals with glasspacks on it. Just too loud when towing. I don't mind to hear it but so much. What do you guys have that sounds pretty good. I am leaning toward Dynomax super turbo.

I requested my dot number on line last week. I have heard nothing so far. How long does it take? I made a double post. How do I delete one?

I requested my dot number on line last week. I have heard nothing so far. How long does it take?

My truck and trailer are only over 10,000lb when hooked together, so can I post my numbers on my trailer since that is the only time I will need them?

I have been pulling my Bobcat tractor with my Pathfinder most of the summer and fall while waiting on the perfect truck at the right price. I got within $500 of trading a few weeks ago. The Pathfinder is in the shop for a new tranny this week. How do you think I feel about that $500 now?

I am getting ready for colder weather and a couple of people asked if I would clear their parking lot and or driveway if we get a big snow . It is hit and miss in KY. Do they make a seat heater that you can plug in to help out a little when you don;t have a cab. The ones I see are only for...

I was told twice, by my salesman, that even though it looks like it, the 225 does not have individual rear brakes.I did not ask but he went out of his way to tell me. I did not concern myself because they are not nearly as handy on a hydro since you already have your right foot busy. I removed...

How do you remove the screen in front of the radiator? It looks as if it should slide out for cleaning but on further inspection it appears as if you may have to remove the section above it to give it room to be pulled out through the top.

Finally got it in Friday and have not had much chance to use it but at least it is here. I like most everything about it except power. I hope it improves as it breaks in. I love the seat and I am glad I went with the 60" loader bucket. it makes it much easier to see.

I am about to make the call. Bush Hog squealer-5ft 3 years old,looks good but has had gear replaced by a dealer I trust. It is on his lot.=$650 International Im500-5 ft couple of years old but has never been used (tractor died) =$550 Hawkline 5 foot- It is new on local JD lot. Looks like the...

I ordered a 225 on Monday June 15. It has been a week with no info. How long did you guys have to wait on your order?

Is it OK to use a come-a-long to secure your load? I used to see it done quite a bit but not anymore. I know you are not supposed to wrap the cable but from point to point is it OK?

I got the box blade so now to the mower. I need a decent 5' model. I have looked at CL at tractor supply, King Kutter, Howse,and International and they all look more or less the same. Do I shop by price or one better than the rest? Is their another brand I need too look for?

I talked to the owner on Friday and worked out some details on the models I am interested in and he said "It will be no problem if I order it". I got an add in the paper on Sat. with the promotion in bold print and an inventory of the tractors he had in stock. I look at the Bobcat site this...

I may end up buying new if I can't find used so what are the brands that are solid but won't break the bank. I need a 5 or 6 foot box blade and a 5 foot RC.

I am considering a tractor purchase. I have some work coming my way in the future if all goes well. I was hoping it would be another 18 months but it looks like sooner. I am trying to keep the total cost low during the first year or so. Does this make sense.I am making the #s below easy to work...

Anyone got a good deal on a CT122 during this rebate frenzy. I saw a sales order for $9500 for a ct 230. Can you get a 122 that cheap?:confused:

What does one weigh. I have been told to figure anywhere from 800lbs to a ton. That's a pretty big difference. Anything over 1500 lbs and I am running pretty tight. Anyone know? I know it says 16 Inches in the title but I meant feet. I just can't figure how to edit the title.Sorry

I have been lurking around for a while and am nearing tractor purchase. I am floored by the deals I am seeing on the Bobcat 225/230 with the free FEL. It is more tractor than I wanted but I can't find anything close to it in price. I have looked at the big 3 as well as Mahindra and MF. I don't...

I am planning the purchase of a compact tractor and I have it narrowed down to a couple. The price and features are the same. One is 2000lb 22hp and one is 3000lb 27hp. I am torn as to the best deal. I was leaning toward the larger but I worry that it will end up being unhandy due to size. With...

I have been in the hunt for a compact for a month or so and was looking at something around 22hp and 2500lbs with FEL on. I was thinking hard about a Bobcat 122 until they put the ct225 on sale for less. 1045.00 with a loader. It is more tractor than I was planning on but I am having trouble...