Search results

Woods9000 on my L3710. There's a pinhole leak on one of the lines. Its one of the longest lines on the setup too. No idea how the pinhole got there, but its away from all mounting surfaces, bends, couplings, or anything. Right on the "straightaway" on the line. Easy access, right there. Is...

https://store.wrlonginc.com/products/valve-solenoid-12gpm-valsold03s How does one remove that? Like anything else, a quick swap turned into a $100, one week wait. Thanks.

2000 or 2001 L3710. I'm not exactly sure what to call these parts to be able to do a proper search: control valve lever? the lever that maneuvers the bucket. as you can see, that heim joint broke off. and something tells me I'm not going to be successful getting that broken bit out of...

In need of a grapple on the front of the tractor. Equipped with a skid steer quick attach. I'm thinking something along the lines of 60"-66". Smaller size. What's the weight limit I should be looking for? Local place has a 62" that's 820#. Guy on a forum I frequent builds a single ram, 60" one...

2001 L3710 If I put the key onto the run position, not start, the little light on the dash doesn't kick on to "preheat" the glow plugs. I swear that light always kicked on at least briefly. It was in the upper 30s the other day, and nothing. Tractor did take a little bit to crank to get it...

Going to go ahead and change the hydraulic fluid in my L3710. Tractors and hydraulics aren't quite my forte. There a go-to place for filters and stuff? Like a SummitRacing, only for tractors? I punch in the filters into Amazon and I get filters compatible with an L3710DT model; not sure with...

I'm smack in the middle of a drainage project in the backyard. Got a 100' trench dug 2.5' deep. Laying 1 1/2" stone, fabric, more stone, 4" perforated PVC (green stuff), and finally more stone all the way to the surface. Going to leave the stone exposed. The dirt from the trench I need to move...

Looking to add a thumb to my L3710. Prefer hydraulic, but a manual one is fine. I've got a Hobart 180 220v welder on mixed gas, so I'm fine with welding. The Woods9000 backhoe runs off its own hydraulics from the rear PTO. Where would I be tying into to get the thumb going? I'm going to have...

Heyas. Got an L3710 with a plow setup. Used Everything Attachment's third function kit. Works great, minus one caveat. The fittings by the plow side are incredibly hard to engage. I pull back the collar and insert the male into the female, and I have to use all my strength to get them to click...

Hey there. I have a Kubota L3710 currently with a Kasco Uni-Hitch setup. Its garbage. Utter. Garbage. I've fixed it a few times, but short of welding 1" thick steel plating to the entire unit it, it keep twisting on me; especially when attaching the plow. The latch dogs have also always given me...

That time of year again. Our driveway is a quarter mile long with a somewhat steep hill at the end. I've got an 8' plow on the front and a Woods9000 backhoe on the rear of my L3710. As of right now, the driveway is a sheet of ice. My F250 with studs barely makes it up. Wife's car, don't even...

Machine is a 2001 Kubota L3710. I swap between a FEL to bring in firewood, and a plow setup from a truck for snow removal. Running a Kasco Uni-Hitch setup. Its awful. I can't stand it. Came with the tractor when we bought a few years ago. If I had one attachment that stayed on, it'd be fine. But...

Is it possible to get parts for this? A pin sheared off that locks the attachment in place. The cube like parts near the top. The bolt porting sheared off. This part; sorta. The above pictures belong to Titan and I doubt they would work. I can't find a parts diagram for Kasco Uni-Hitch...

Greetings all. I have a question about plumbing a front snow plow on the front of my L3710. Here's the tractor: I bought an 8' Fisher snowplow that has two hydraulic rams for angle. The plow is connected to a skid steer style quick connect plate. I plan on using the mid mount PTO to drive the...