Menu
Forums
Today's Posts
New posts
Search
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Classifieds
Auctions
Database
Quick Review
Quick Owner-Page
Register
Log in
Join
What's new
Search
Search
Search titles only
Today's Posts
New Posts
Search
Members
Current visitors
Top posters of the month
Menu
Log in
Join
Forums
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
oldnslo's latest activity
O
oldnslo
replied to the thread
JD850 with JD80 front end loader--Hydraulics issue, bucket strains to dump and has no strength
.
Sounds like one of the quick disconnects has come partially undone or is failing in the dump circuit. When these fail they act like a...
Jul 29, 2025
O
oldnslo
replied to the thread
Hydraulic AG couplers and heat
.
Sorry but no I do not know what size the O-rings are.
Jul 28, 2025
O
oldnslo
replied to the thread
Hydraulic AG couplers and heat
.
There is an O-ring in the female half of the coupling that can be replaced to stop external leaks.
Jul 28, 2025
O
oldnslo
replied to the thread
WoodMaxx Chippers
.
I believe you are correct on majority USA assembly and imported version is noted on the website.
Jul 27, 2025
O
oldnslo
replied to the thread
Massey Ferguson 1835M Hydrostatic Transmission
.
Has the dealer checked charge pressure when hydrostatic tranny isn’t working? Does it make any different noises when not working vs...
Jul 27, 2025
O
oldnslo
replied to the thread
Ginma 304 backhoe problem
.
Not sure where you are located but there are O-ring kits available online. I suspect that those are metric sizes. Typically sizing is...
Jul 27, 2025
O
oldnslo
replied to the thread
Ginma 304 backhoe problem
.
Yes O-rings are made to specific sizes and there different materials or compounds used for use with various types of fluids. Possible a...
Jul 27, 2025
O
oldnslo
replied to the thread
Throttle Lever Friction Disk Failure on '21 3620H ROPS
.
If like my 2400H it is just sandwiched between a couple of steel washers and has a wave washer for setting tension or friction. On mine...
Jul 26, 2025
O
oldnslo
replied to the thread
Hydraulic (flexwing mower) question...
.
Good job on diagnosing the problem(s). I suspect the “blind” cavity has radius on the machined corners and requires the rounded or...
Jul 26, 2025
O
oldnslo
reacted to
TerryR's post
in the thread
How do you clean your greasy loader pivots?
with
Good Post
.
I don't.
Jul 26, 2025
O
oldnslo
reacted to
GS650GL's post
in the thread
Solving the “Floppy Bucket” by adding a flow restriction
with
Good Post
.
All brands of tractors can and do have floppy bucket syndrome, not because of a defect but because of the laws of physics. During the...
Jul 26, 2025
O
oldnslo
reacted to
ptsg's post
in the thread
Solving the “Floppy Bucket” by adding a flow restriction
with
Good Post
.
There is always the possibility of adding a regenerative valve to the circuit...
Jul 26, 2025
O
oldnslo
replied to the thread
What is it with all the distracted driver lately.
.
How many people are more concerned about the GPS screen or talking on phone vs looking through the windshield? From what I have observed...
Jul 26, 2025
O
oldnslo
replied to the thread
Hose ID
.
Does it have markings on the hose like the one behind it that says 9.5 mm?
Jul 25, 2025
O
oldnslo
replied to the thread
Ferris scalping
.
Is it happening turning both was ways or more prominent in one direction? If you stand on one corner of foot platform does the deck tilt...
Jul 25, 2025
Forums
Top