Has anyone used a Woods RD 7200 with a 1954 Ford NAA? To hook them together, I had to point the pins towards each other because the lift arms do not spread far enough otherwise. Because of that...
Im in a mess..3 pt wont lift so lifted top off...replaced piston and seals and pin that was worn
then tried to addjust as per video.but when i bring arms up to botton of spring
there no way i can...
Im looking for teflon seal for lift cylnder..1954 forn naa..pistion is 2.5 inche dia
i cant where to buy tefon or neoprene..i wrecked 2 leather ones...any assist where to purchase
I bought a used Woods RD 7200 finish mower to replace my old KingKutter 72" finish mower. In attaching the Woods to my 1954 Ford NAA tractor, I found that the hitch pins on the Woods are 3 inches...
So it's a fix one thing find another kind of tractor it seems. After *ahem* fixing the fuel issue, found a leak in the radiator. Long story short, 2nd replacement radiator is holding coolant so...
I bought a 54 NAA from a guy a week or so ago and I'm stumped. Tractor fired up, ran around his yard, picked up a 5' Box Blade and drove onto my trailer then stalled out and battery died before...
I have a Ford naa jubalee tractor. I have updated it to a 12volt negative ground electrial system with electronic ignition. I have spark at the spark plugs and fuel.
I am trying to set the...
I am being gifted a 54 ford jubilee tractor and I am trying to figure out what attachments will work with it and would love all of your help! I have never used this kind of tractor before and have...
My NAA is leaking between the hydraulic pump and the flange at the bottom that holds the pressure and return lines. Before I remove the 3 bolts that hold that flange on, I would like to know what...
New to this forum . Just pick up a 54 Ford NAA this past weekend . The rear wheels are loose . Ive read about the hubs being worn out and causing this problem but on one side the axle nut or axle...
Hi. I have searched for an answer, but come up with zero. I hope to get some help.
My dad has a 1954 Ford NAA. It has a loader and power steering, even though I understand that NAA did not come...
Good morning,
This is my first post. I live near Waterville NY and have a 1954 Ford NAA that I have owned since 1983. It came with a heavy plow on the front that I use for snow plowing. It raises...
First post here but have learned a lot from these forums so have to say thank you! I will try and make a long story short...
I have a very nice NAA with vane pump that wouldn't lift a heavy load...
Picked up this orchard tractor a week ago in order to have a dedicated mower setup. I don't know about the rest of you, but after struggling with removing and installing your typical three point...
So I got a new radiator for my 1954 NAA. Today, I worked on getting the sheet metal off. Nightmare! There are several bolts and screws that go into captive nuts. With few exceptions, the captive...
hey all, I recently picked up a 1954 ford naa and I am having a hard time finding out what fluids to put in it. trans, motor, etc. was hope'n someone could point me in the right direction. i have...
I was wondering if there was a newer owners manual printed in 1954 or if Ford had the same from 1952/53. when it was printed until end of production? Also, I have found that a gear change was done...
Hi there, new here. My boyfriends 54 NAA will not hold prime on the hydraulic pump. We got this tractor a while ago, and when trying out a back blade, hit a rock and after the lift would not work...
Looking for a source for the 4 bushings that go into a morflex 302 coupling center hub. I removed the driveshaft and the bushings are quite worn and should
be replaced while apart.
Thanks,
Pete
My in laws NAA lift stopped working, so I picked it up and brought it to my house for repair. The clevis pin broke allowing the rod to fall out of the piston. Drained the reservoir and found...
I did an oil conversion and will give you the canister cover EAA6737B and the bolt with oil holes in it.....Free to good home.
Rear fuel tank support bracket NCQ 9097A also free....new tank came...
I just started working on my great-grandfathers 1954 Ford NAA that has been parked in barn for at least 5 years but no longer than 10. I am as green as you can be with tractors (first time on one...
I finally went up to the farm and got my non-running NAA up on the trailer with what turned out to be a defective winch. When I bought the tractor, the previous owner loaded it up on the trailer...
Ok to begin with, I'm a transplanted Hawaiian in Tennessee who decided to buy a recreational piece of land. Got a good deal on a running Ford NAA, and without knowing a whole bunch took the...
Does anyone know where I can get an exploded diagram for an old vicker hydraulic pump? It is off a shawnee loader that is mounted to my NAA. The pump drools a pretty good stream of fluid from...
I have a 1954 Ford NAA that sets all year in a shed in the Upper Pennisula of Michigan. I just use it for putting in food plots for deer. Now this area is pretty remote I have no electricity etc...
I have solved a difficult and nagging problem that would have taken only 5 minutes if I had known what I am about to write about my 1953 Ford Jubilee edition NAA tractor. The problem was the...
Seems like the rear seal of my hydraulic pump for the 3 point hitch just let loose. I thought it was the o-rings where it connects to the lines, but after checking it more closely it's leaking...
As a new owner of a Ford NAA, I am wondering what that proper service levels of the transmission, hydraulics and rear end are. I have the manual which gives the quantities, but how do you see...
I've called a number of places looking for brake drums. A number of dealers list the drum on their web site, but when I contact them, they are sold out. Is there some reason that the NAA/8N...
Is there a way or can I tap off the hydraulics on this tractor. It does have the new style hydraulic pump (piston type). I want to make a quick connect point so I can run a log splitter or maybe...
Installed new oil pump .. repaired distributor. Cannot find timing marks on flywheel to install distributor at the right crank position tried just do it by #1 piston still no luck...Have gas and...
1953 Ford Naa Jubilee - Clutch slipping - Which clutch to order ? 10" or 9 " ?
when looking to order a Clutch kit there are two options - 10" or 9" - Which should I get ?
1953 Ford Naa Jubilee - Clutch slipping - Which clutch to order ? 10" or 9 " ?
My clutch is slipping and I am planning on getting a Clutch replacement kit - As I am looking I am seeing two...
Hi Gang,
For the last couple of years, while brush hogging the fields, the tractor has NOT run good at all! I thought maybe, it was a "fur ball" or something from ethanol, but have never been able...
My NAA has been losing oil pressure for awhile and now it is at zero, dip stick shows clean and full, too clean after running about 30 hours with low (10 psig ) to zero. The oil looks like it was...
I'm looking for a picture of the Ford NAA throttle stop (that I believe bolts to the manifold and hangs down around the throttle control near the governor). I assume other 134 ci engines have the...
I have a 1954 Ford NAA. I have had the tractor for 30 years and it was missing the hydraulic pump when I got it. Someone made a plate to cover the place where it bolts to the engine and had cut...
I may have reversed the poles of my newly charged battery when placed into the NAA (original 6V system). The tractor started up fine but when turned off the generator kept turning. Yes, the fan...
Went to use my tractor to do some snow plowing and when I attempted to raise the back blade it wouldn't move off the ground at all. I thought it was frozen, but moved the tractor a little bit...
I shut off my '53 NAA this evening for a couple minutes and when I went to restart it the solenoid just clicked. Tractor had only been run a couple minutes (backing load of corn in the barn) so...
Rebuild 134 engine including new oil pump. initial start-up sounds great, but no pressure on the gauge. I removed the dist, and fashioned a long screwdriver to turn the oil pump with a drill...
My '54 NAA has been doing fine all summer. Last evening, I started it to do some mowing. It did not want to start, and that has never happened before. With the help of some ether, I got it going...
I have my newly acquired NAA just about ready to go into service. One thing I've noticed is that the clutch really has a different feel than the one on my 9N. The throw is a lot shorter and it...
I just bought a 1954 Ford NAA and I am in the process of doing the usual tune-up and fluid replacements. I changed the oil and used 10W30 which is what I use in a 9N I have. The tractor starts...
I just replaced a jubilee steering box with a used one...All is good with the box except the top Steering bearing assembly Bearing Assembly - 8N3517
is bad and doesnt seem to want to come out.I am...
I'm retired and just purchased a Ford NAA with a Sherman Backhoe. Plan to restore it and would like to contact other NAA owners, especially those with a Sherman backhoe.
Hi,
I just changed out my NAA distributor with a used one. Tractor starts and sounds good. While taking it for test spin, I noticed that it didn't seem to have any oil pressure. It never did have...
My old snow plow truck leaks tranny fluid awful. I mostly haul wood and push snow. Would like to put the plow on my Ford NAA but am not an engineer. Anybody done this?
i just bought a '54 Ford NAA, looks to be well taken care of. Question is....at 800 rpm, not at normal operating temperature yet, 40 degrees outside - when i move the lever to raise the 3 pt...
Last weekend I was mowing with my '54 Ford NAA. After 30 or 45 minutes, it started running rough and losing power. I barely made it back to the house. Thinking it could be a little dirt in the...
In the previous thread I mentioned that I was at my neighbors moving a house trailer with my Fordson. One of the guys who ended up taking the trailer was trying to tell me that my tracor was Ford...
I've got a 1953 Ford NAA Golden Jubilee with a leaking gas tank. I had it "fixed" about 15 years ago and it's starting to leak again underneath where the mounting bracket is welded / spot welded...
I have a 1954 NAA that I am using with a 6' King Kutter finish mower.
I have shortened the chains on the 3-point hitch to limit mower sway.
Questions: How much sway is acceptable? I see that...
When I press the right brake pedal on this tractor, or even at times if I don't, the right wheel locks up and does not release until it is dragged along for a while. I'll pull the wheel and look...
When I press the right brake pedal on this tractor, or even at times if I don't, the right wheel locks up and does not release until it is dragged along for a while. I'll pull the wheel and look...
My NAA came with the vertcal exhaust stack broken off and a Harley motorcycle muffler stuck on the stub. I ordered a new pipe, which turn out to be a nicely bent sheet metal pipe. The issue is...
Father-in-law has on his to-do list to build a log splitter. So far he's only been collecting the various bits and pieces for the splitter. He intended to run this off the hydraulics on his old...