Hello to all & HNY ! The original Goodyear (GY) 2WD 7.5 - 16 ribbed tires are close to their end. I have tubes in both of them now. Looking for recommendations on replacing both front tires...

I have a 1998(?) M5400. It's a 4 speed trans with a high/low/reverse range shifter on the left side. You do have to press the clutch to shift it, so I don't believe they call that the shuttle...

I'm looking at a used M5400 this week. It's a 1998, 3300 hrs. What's the good/bad/ugly on these units? I was hoping to find something newer in hopes that I'd have less maintenance problems, but...

Does anyone have a diagram or photo of where the temperature sending unit is located on a Kubota M5400 2WD tractor?

I am looking at a used Kubota M5400 SD. Owner is unsure of the year. I think the serial # is 60698. How can I find out what year this tractor is?

Looking at the specs the M4700 uses a F2803-LA and the M5400 uses an F2803-A. Note the differences in HP, PTO HP, and Torque From reading the WSM I have about the only differences I've found...

I have a ten year old M5400 two wheel drive. I am looking at a newish 2013 MX5100DT (49hp) four wheel drive with a front end loader. My question is simple. Do yall think that the newer smaller...

My first 'big' tractor is my 1999 Kubota M5400 4x4. Most of the hours since I've had it have gone into mowing my rough fields with a 6' Modern Ag rotary cutter. I've learned lots of lessons...

Howdy to all, I have a 4 wheel drive Kubota M5400 SU with 800 original hours. I purchased it from the original owner last fall. Here's my problem, with the tractor running, but stationary, when...

I just bought a Kubota 2wd M5400 with a front end loader with less than 700hrs. It's a 1 owner tractor that I know the history of - no problems whatsoever. I changed the hydraulic filters along...

I am looking for a shop manual for a m5400, anyone know where I can get one or where to download. Thanks Mark

New owner of a m5400 kubota, not sure of the year but was changing the hydralic oil and filters, when finished. Started the tractor, nothing works, no three point hitch, no steering, no pto. Also...

What would be a fair and reasonable price to ask for a M5400 , 2 wheel drive, Allied fel , bucket and hay spear. Has 1726 hrs everything good except one cylinder on loader leeks a little? Any help...

On start up engine smokes badly, just started this. It also seems to be overfilled with oil. I know I didn't overfil it so fluids must be leaking in, its not water so must be diesel or hydrolic...

When we returned from the Czech Festival in Praha Tx, this afternoon I found a hand delivered note in the mail box, from our Kubota dealer saying "please call about a recall on my Kubota M5400...

I am looking for an attachment that can be used to trim back brush that has grown into road ways. I am on a M5400. Any thoughts Ie sickle bar or rotary and how would it mount and drive? email...

I am trying to answer a question from another member but I am not sure if my answer is correct. I am going to post here in hopes of being corrected if I am wrong. Based on the connections to the...

Hello - The seller of my M5400 did not provide the manual as "promised". I've ordered one. Certainly the dipstick on the floor in front of the seat is where I check the level. But what's the...

I'm up to a whopping 8 hrs of seat time! Problem is the seller did not provide the manual as "promised". I've ordered one. Till then can you folks help me not neglect this beast? I know to...

Hello all. I just bought a used M5400 w/FEL & R blade and have some very basic (silly) questions . I've read many posts. The seller forgot the owners manual so I can't refer to that till it...

I have a kubota m5400 tractor and the 3 pt hitch lever is frozen ,won't raise or lower. Any suggestions? Oh yeah this tractor took a "dip" in a pond a few months ago.(By dip I mean completely...

I have a kubota m5400 tractor and the 3 pt hitch lever is frozen ,won't raise or lower. Any suggestions? Oh yeah this tractor took a "dip" in a pond a few months ago.(By dip I mean completely...

Any help that could be provided as to a fair price to pay for a used Kubota M5400 with LA 1001 loader would be greatly appreciated. I have surfed the internet a bit and haven't found many listed...

I was looking in the Wix filter site for filters for my M5400. They list two engines for the M5400, the F2803 and the V3300. My tractor is used and I bought a used manual for it from another...

I am selling my Kubota M5400. It is posted in the classified section. I will be upgrading to a larger model.

I may put up for sale my '97 M5400 Kubota. It is 2 wheel drive, 275 hours, aluminum canopy, brush guard, stored inside, perfect condition. I think I will ask $12,800. Does this sound like a fair...