Hello! I am in the process of replacing the double clutch on my 1958 Ford 861 and am ready to put it back together. Can someone help me with the torque requirements for the flywheel to engine...

Hello all, this is my first post and I’m here because I am having issues with a the ford 861 I recently acquired. I was running the tractor the other day and cut it off to grab a beverage. When I...

Hello, this is my first post, thank you in advance for any advice you guys can give me for dealing with my ford tractor issues. I have a 1958 ford 861 tractor with gas engine. I recently took the...

I removed the transmission filler plug and noticed the oil is milky, which should indicate water is mixed with the oil. This is a Ford 861 5-speed transmission and the shifter doesn't require a...

I have an early model either a 57 or 58 Ford 861D and it has only one return fuel line from the standpipe to the brass fitting that screws into the side of the block. I understand in 1959 and...

I have an early model either a 57 or 58 Ford 861D and it has only one return fuel line from the standpipe to the brass fitting that screws into the side of the block. I understand in 1959 and...

I have fuel getting into the crankcase on my 1958 Ford 861 diesel and I plan to start with inspecting the Feed Back Line as the possible problem. At this point I have nothing that will confirm if...

I purchased a Ford 861 tractor from an auction last year. They said it ran great, stuck clutch. Liars...lol. someone decided to do a half assed 12v conversation by putting a 12v battery and coil...

I purchased a Ford 861 tractor from an auction last year. They said it ran great, stuck clutch. Liars...lol. someone decided to do a half assed 12v conversation by putting a 12v battery and coil...

Hi!!! Today we became the proud owners of a Ford 861 from a local farm auction. The first question we have is what goes into, is it worth the trouble if one cannot afford a skid steer, or is it...

Hello all I have a 1958 Ford 861 gas model that was thrown in with the house I purchased. This past week I needed to replace the worn water pump so figured I do some other maintenance while I...

My " new-to-me" 1960 Ford 861 appears to have a carb issue. It will start OK, but when I try to give it any throttle, it just tries to run away, with regards to high RPM. I took off the carb and...

I just bought an 861 and spent the day changing fluids and doing a little clean up. I noticed an oil leak at a spot on the block just to the right of the dipstick. Some previous owner had tried to...

I have looked at the schematic showing the govenor compensating spring (#20) but cannot find where the 2nd end connects. There is a hole in the bell-crank for one end but I read the other end...

https://tippecanoe.tr.craigslist.org/grd/4820426505.html Seems like a lot of tractor for $1500, has powersteering and the tires don't look bad. Not for me but might be a good deal for someone.

Hi All- Joined because I just acquired a 1957 (58?) Ford 861 Powermaster with an FEL, and figure I'll need some experienced friends as I fix up the rough spots. First project is the carburetor...

My three point hitch seems to only work intermittently. It works most of the time, but it is often slow to respond. If the control lever is all the way down, I have to raise the lever 7/8 of...

Hey to all here at TBN I am a long time reader and first time poster. I am in the process of rebuilding an old Ford 861 diesel and was thinking about adding a turbo to it. Has anyone seen...

Hello, this is my first post, so bare with me. I have a 1956 861 Ford tractor with 11" x 28" power adjust rear wheels that have corroded around the valve stem so bad that the tube is showing quite...

I have a Ford 861 and it is having issues revving up. It starts and idles just fine but when it get's to a certain point while throttling up, it wants to die unless you throttle down. Any ideas...

I have my father in laws old ford 861 and it has been very reliable. Last winter I changed all the fluids in it because he stored it outside at all times and it was working fine after that. It...

I am a relatively new tractor owner and have a '62 ford 861. Does anyone know the proper belt size for the power steering pump? It appears like mine is too long. Adjustment is all the way...

I have a first or second year gas motor 861. Newly acquired and used for the first time. I did the standard, changed fluids, filter, plugs, wires, thermostat and all seemed well. Tractor ran...

new tractor owner, with problems from day one!

Looking for advice on a purchase. I have an 8n currently and love it. It's a great little workhorse. I use it to mow with a rotary cutter and different farm chores. Best of all so far I have...

Hello! Below is a pic of the hood badge on the 861. Just curious of if the badge is proper for this model? In other words, should it read "801"? This is a 1958 model, serial 24xxx (cannot...

Hey gang, I stumbled across a 15' woods batwing finish mower but wasnt sure if the Ford would be up for the challenge. Its a older batwing mower but on woods website they say the motor HP should...

Hi! Have been looking for a while and just picked up a Ford 861. Seems to be in nice shape. I have ordered reprints of the owners manual, shop manual and parts manual. Is the IT manual better...

Hey gang, I recently got around to throwing some paint on the tractor and I bought the paint from TSC. Ford Red and Ford Gray. Red turned out great but the gray Im not sure.... Its almost like...

I am putting a picture up for a friend. I understand this is not the normal setup for the 3 point hitch and rockshaft for this series tractor. Can Soundguy or anyone say if this 3 point is...

I have rebuilt my carburetor and it will not suck gasoline into the manifold. I took the top off the carburetor and the bowl has gas in it. I spray starting fluid in the maniforl and the tractor...

I have my Grandfather's 1958 Ford 861 Powermaster. I was nine years old when I saw it come of the truck new. I'm part way through restoring it, having rebuilt the engine last year and replaced...

I can't get the PTO to engage on my Ford 861 Powermaster tractor. It seems like the lever for the PTO won't push back all the way to get it to engage. I removed the side access panel and the shaft...

Thinking of buying this loader and was wondering if anyone knew if they would match up. Hope the pictures load...

Trading up from a 49 8n. Excited about live PTO and twice the HP. Losing a loader though...

Hey everyone, Newbie here...I just bought a 1958 861 Powermaster. At low idle I hear a noise which sounds an awful lot like a coffee grinder! I believe the hydraulic pump which runs the 3-point...

Hi guys. I had a thread on here last week about my new (to me) Ford tractor, some of you wanted pics so I thought I'd start a new thread. I will tell you, the more I look at it and tinker, I am...

Hi all. My first post here, I've done numerous searches here over the last year as I've been trying to find my first tractor, but never registered till now......this is a great place to get...

Hello all, New guy to the board, but not new to tractors. Still got a lot to learn. I've got several different projects in various stages. I like old Ford and John Deere stuff. My current...

Looking to buy an 861 powermaster. Any thoughts on reliability?

Just put new muffler and manifold on my 861, along with a carburator kit. Have issues now with it stalling out when increasing the throttle. Have done all adjustments that I can think of. Took...

I have a '57 Ford 861 LP model that I use to cut 15 acres of grass with on a bi-weekly basis...All in all, a very good tractor with factory PS too... I do have a chronic problem with the gear...

Was wondering what it would take to change out the clutch on a recently purchased used ford 861? I know I need to support the tractor on both sides and was told to stick a wedge up front to keep...

has anybody ever repaired third gear on an 861 tractor. If they have how hard is it to do. and what do I have to do to replace the gear.

has anybody ever repaired third gear on an 861 tractor. If they have how hard is it to do. and what do I have to do to replace the gear.