I live in Michigan and need 2 of rear wheels for a 1995 Ford 1720 where the rear rims are one piece, with a 6 bolt pattern. Tires are 11.2 - 24. Anyone know anywhere to find these 1 piece rims...

Just bought a Ford 1720 tractor with serial number UL33034, model 412A and engine N873. Used the year made table provided on this site and can’t find mine listed. Would someone know the year it...

Hi everyone. Ive got an issue with this Ford 1720. Its a 2WD. It does not have a loader. Its a 1991 model. It has been a sweet little tractor for around the house and small bushhogging. Weve owned...

I've got a 1991 ford 1720 trying to locate the rubber boot on bell housing my Tractor has a front end bucket on it is the boot behind that bracket or is it up on top under steering column

I have a 1998 ford new holland 1720. 1000hrs. Has a 7308 loader attached. Just bought it. The loader is slow moving at any rpm unless I dead head the 3pt all the way up then it flies. I read in...

Hi, My 1986 Ford 1720 3 point and loader stopped working. I noticed the loader was working real slow for a couple weeks. Then it suddenly stopped working. Also the 3 point is not working. Any...

Worked fine until I replaced the hydraulic filter. Fluid level are good, no leaks or whinning noise. Fluid gets warm after running for a little while. The suction line gets warm,so I believe the...

Hi all, up until now no issues with starting. Cranks over with no smoke. Here’s what I’ve checked so far: -neutral switch, PTO is disengaged. Is there another safety? (It has no switch on seat)...

Hey guys, first post in the forum. I have a 1990 ford 1720. This is my first tractor so I’m still figuring out all of the tricks to run it smoothly. I am having issues getting the pto to engage...

I posted this in the Ford forum with no response, hopefully I have better luck here. I think I may have inadvertently damaged the PTO clutch on my Ford 1720 SSS. It was working fine all winter...

I think I may have inadvertently damaged the PTO clutch on my Ford 1720 SSS. It was working fine all winter. The left floor board (clutch side) was loose & rusty so I removed it to repair. I...

I have a1995 Ford 1720. On the rear wheel shaft I have a lot of fluid leaking out. I purchased Part #10, ball bearing seal, off the parts diagram below. I have removed the 4 bolts out of part#9...

Hi All! I just received my lower knuckle seal from Messick's. Looking for easier way to remove the seal from the housing so i don't muck up the casting where it's housed. I found a...

Problem: My Ford 1720 wouldn't crank. Power was to glow plugs in ignition switch Pre-heat and start position but nothing to starter solenoid in start position. Jumpered starter solenoid and engine...

Hey all looking for some pics of your 1720 backhoe subframes factory or homemade specifically the front end that attaches near the loader posts i recently purchased a 758a backhoe off a 1510 but...

Good day all! I've read and read on this forum and it's been a great help so far.:thumbsup: However, i'm looking for some assistance on the wiring harness for my new to me 1720. The previous owner...

Good day all, Quick question. I ordered a service manual off good ol Ebay. The one I ordered has a copy right date of 1989 and has printed on the inside cover tractors up to 1988 year model. My...

Probably a simple question but I have a system like the picture.My question is what are the small "low pressure' line for ?they run between all the injectors and the last one goes to the fuel...

Hi folks, and thanks in advance for the advise! I am essentially a tractor "newbie", but my wife and I have just decided to purchase a 4 acre "horse farm" in our retirement and I'm gonna need a...

Are all Ford 1720 tractors doomed to have a dual stage clutch? I know the run on these tractors were from 87/99,i have a 1990 and according to the $26 service manual I could have either dual or...

Hi Fellas, Yep, it's been awhile since I've been here. But I know this is the place to come looking for some expert guidance for my FORD 1720, a 1989 4X4 with FEL. I have owned this tractor...

Hi All, After getting a quote of nearly $2400 from my local New Holland dealer (~$100 parts, 20-24 hours of labor!!) to replace the leaking timing cover gasket on my 1995 Ford 1720 I have...

I bent my pull arm on my ford 1720 3-point hitch. Not much about 1 1/2 inch in to the center. It's still flat, just takes a turn to the left. I had a 3-point back hoe on it that I had just got...

I recently installed a new clutch in my Ford 1720. The good news is that the clutch works perfectly the first time. The bad news is that I seem to have created two problems in the process...

Idling too fast. How to adjust? What is the right idle speed?

I have a 1989 ish Ford 1720 4x4 with 1300 hours. After sitting for the winter the clutch appeared to be stuck. I depressed and released it very quickly several times and it seemed to come...

Recently doing some dirt work with my 1989 Ford 1720 under very dusty conditions the tractor lost power and stopped running. I changed the air and fuel filters however no change in how the...

Need help Installing disc brakes on Ford 1720. Can anyone walk me through a break job on a Ford 1720?? Is it necessary to drain all the hydraulic oil before starting?

Does anyone know the engine oil capacity on the 1720. Can't track down the manual. 4 quarts got the oil right in the middle of the dipstick but I recall it being 5 in the past. Thanks, Nick.

Where can I get a less expensive, good quality hydraulic filter for a ford 1720? Any information, brand, part numbers, etc. Would be greatly appreciated... Thanks!!

I am a new member to the forum, and a novice with hydraulics. I own a 1989 Ford 1720 with FEL, 3PH post hole digger, and rear plow. The tractor has factory installed rear hydraulics consisting...

I just finished a complete overhaul on a ford 1720 with less than 600 hours on it due to a mouse getting by the air filter and getting urine down in the engine. Had to get it bored and put on 40...

I just finished a complete overhaul on a ford 1720 with less than 600 hours on it due to a mouse getting by the air filter and getting urine down in the engine. Had to get it bored and put on 40...

My Ford 1720 tractor, 1800 hrs, is making a high pitched noise, something like a slight squeal, continuously when I engage the clutch wether in neutral or in any gear. It's seems not as bad at low...

I have a column shifter for 1,2,3,R on left of the steering wheel. I noticed that once the tractor runs a while and I use the shifter a lot to go forward / reverse spreading dirt, oil is leaking...

How do I test glowplugs and change them on a ford 1720 FWD?

Hello All: I recently installed a used Ford 7108 loaded on my Ford 1720. This thing worked great until I used it for 2 or 3 hours. It gradually became unable to lift the front tires off the...

I need some help here folks, I acquired a 1990 Ford 1720 from my father and I recently purchased a Ford 7108 loader. The link below is not the exact one that i got but it has all the same...

I believe this site will be most informative about my Ford 1720 8N Tractor:laughing::laughing:

I am considering the purchase of a 1989 Ford 1720 4x4, FEL, live PTO, ~1,400 hrs. It's a decent little tractor. It starts easily and is in decent condition considering the age. I've talked...

can anyone tell me the size of the fuel and return line on ford 1720? thank you Roman

I have a Ford 1720, what type of hydraulic/transmission fluid does it use?

Hi Fellas, My '89 FORD 1720 4x4 Owner's Manual says to check (& adjust if necessary) the valves every 600 hours. It has the 3-cyl Shibaura diesel engine. The tractor has logged 3,135 hours of...

Ford 1710 with 465 Hours Hi folks, I'm new to the forum here and have just purchased a 1986 Ford 1710 4wd that had 464 hours on it. It had the FEL, a 60" Brush Hog mower, 60" landscape rake and...

Has anyone had a problem with with sediment in the fuel tank. Does the tank have a screen in it? Is it best to remove tank and pressure wash it out to clean it or can i just put air to it and blow...

Does a ford 1720 have only 1 fuel filter in the glass bowl. I have replaced this one and bled lines but i am still loosing power and rpms at times. Is there a strainer in the fuel tank . This has...

Howdy I'm looking to switch my turf wheels/ tires to ag Looking for front agriculture wheels for ford 1720 either 5.00x15 or 5.50x 16 either new or used anybody have any help or a source other...

I parked my 1991 Ford 1720 and left it for a few days. The tractor was running fine when I parked it. The trouble seems to have begun when I removed the battery temporarily, because I was going...

I replaced fuel filter and forgot to open fuel petcock. Ran system out of fuel and now I cant get it to bleed. I followed steps in manual but it wont pick up fuel...Now what?

Hello folks, My wife and I just built a house on 3 acres and need a mowing rig. I purchased a used Ford 1720 (28 hp, 23.5 hp PTO) with a 12 gear shuttle shift, about 1900 hours, and turf tires...

I'm the original owner of a 1720 that I purchased in the mid 80's. It's only got around 800 hours on it and I have changed the oil twice and the air and fuel filters and the trans/hydraulic oil...

Hey guys newbe here. I'm looking to buy my first 4wd tractor and I was looking at a ford 1720. They guy wants $4200. BUT. The pto makes some kind of noise when it is engaged and it has 6000 hrs...

I have a 1989 Ford 1720. I've been fighting glow plug and instrument panel light issues. I fixed the panel light issues after finding mice had eaten through 5 wires under the instrument panel. I...

I have been toying with replacing the plow with a 60" blower. Ford 1720 PTO HP claimed at 23.5 and it is a 12 speed shuttle shift. Will it have the nut to move our average 8 -12" storm? Thanks!

Last time I used the tractor a warning light came on went off and came on again. I attached pics at first I thought it might be the coolant but that seems full. Any help would be appreciated. Thanks

I have a 1720 tractor and I'd like to put hydraulics on it so I can use a wood splitter and maybe put a loader on it. I have heard you can put a kit on it, or tap into the system. Has anyone done...

I have a 1720 tractor and I'd like to put hydraulics on it so I can use a wood splitter and maybe put a loader on it. I have heard you can put a kit on it but I have no idea where to start. Can...

I have a 1989 Ford 1720. It requires the transmission to be in neutral before it will start. While its been getting worse over the past year, now its very hard to get it to start. I believe its...

I have a 1989 Ford 1720 2WD with loader. Other than replacing the solenoid in 2013 I have had no issues with the tractor for years. I tried to start it a couple of weeks ago and it would only...

After I removed the power steering cylinder bracket under the engine, I attempted to remove the cylinder from the tire side. After I removed the top nut, I realized there was a nut on the bottom...

My intro to the wonders of tractors was in the '60s with a Silver King 3 wheeler. We worked part of 30 acres in Pa. with it. Soon we got the MM to handle plowing and baling. The Silver King...

I have a 1989 Ford 1720 Aprox 1500 Hrs. It has the Ford FEL and Brush Hog 7'-6" hoe mounted on the 3-point. The tractor is running and in fair shape with some repairs needed. FEL is in good shape...

Hello all, Long time lurker first time poster. I just bought an absolutely pristine 1720 (4wd, no cab) with less than 500 hrs on it. The tractor will mainly be used on 52 acres of hunting land...

I have a 95 Ford 1720 on which I recently mounted a Woods Du Al 155 FEL. The DU Al was in rough shape (rusted bucket/hydro fittings and bad hoses). I disassambled the cylinders, cut the cylinder...

Hello, glad to have found this great site. Just bought a 1999 Ford / New Holland 1720 with FEL, 1500 hours, turf tires. Asked my first question in parts/repairs, so jumping right in...

Hi, I just bought a Ford / New Holland 1720 (1999) in "as is" condition, no operators manual included. It seems to be stuck in 4WD, or I just might not know how to shift it to 2WD. Could someone...

Hello I need some help please. I have a beautiful Ford 1720 tractor that my father purchased in 1989. The tractor is now mine. I need a front end loader for it. I stopped at the local ford...

Hello again, I am looking for the wisdom of others before deciding whether or not to try this on my own. I have a Ford 1720 with 3300 hours on it. Its been a great tractor and . On my front axle...

Hello again, I am looking for the wisdom of others before deciding whether or not to try this on my own. I have a Ford 1720 with 3300 hours on it. Its been a great tractor and I have been very...

Hi, I need your help or suggestions. I have a 1989 Ford 1720 which has a 7108 loader on it and does have the factory rear remote hydraulics. Today I was using my Ford 3 point blower to blow snow...

YOU GUESSED IT, BORROWED TRACTOR FROM NEIGHBOR AND THREW A ROD PULLING DIRT. ANY IDEAS ON LOCATING RUNNING ENGINE? SHIBAURA 3CYL LOOKS LIKE.

I am looking at used 30hp 4wd tractors. Local recommended dealer/service center has a late 80's Deere 970 and a late 80's Ford 1720. He is suggesting I go with the Ford due to parts costs. Both...

I have a 1990 ford 1720 that i bought used. Since i purchased it the loader has never worked right. The 3otthe works great, fast smooth and oowerful. To get the loader to work decent the engine...

Ford 1720 (1998) with shuttle will pop out of 2nd when motoring, but not under load. Slight hand pressure on shifter keeps it there. What could the issue be and how to correct it? IF we...

The lever pulls up and goes down like nothing is attached to it,looked under everything is attached and turns shaft going into trans.Can I pull the cover off that the shaft goes through it is held...

Have a leak on left pipe outlet at the fuel injection pump. 99% sure its not the pipe connection but under the flange that pipe connects to. There's 3 oval oblong flanges that appear to be what...

I've been trying to decide which of these to buy, you have to be flexible sometimes when you set your sights for a tractor. Is either of these tractors preferable to the other?Dollar for dollar...

I have a 1988 Ford 1720SSS with FEL that I purchased in 1995 and currently have close to 2300 hours on it. In that time all I have done is maintenance, it has never broken or failed me. I mow...

Hello fellow TBNers. I am considering adding rear hydraulics on my Ford 1720. I have an 1989 model - similar to the New Holland 1720's. I have explored the factory remote kit from New Holland and...

I am considering buying this tractor, asking price is $9500. It`s a 1720 Ford New Holland 4x4 with 680 hrs. 28 horsepower C/W 5ft snowblower, Front loader and 5ft scraper blade, supposed to be in...

This will probably be an easy one for this community. I caused my PTO clutch to stop working when I crossed a dry-ish creek bed with my Woods RD8400 mower running. The spot I crossed was a little...

Had to get the power steering cylinder rebuilt on my 1720, what type power steering fluid does this tractor take, the reservoir has a sticker that sez " power steering fluid" but on top of the...

Does anyone know where I can get after market brakes shoes for a Ford 1720 tractor.

Hello, I'm new to the Ford/New Holland 1720 tractor, and I noticed last night there is something wrong somewhere - Last night, I started and moved the tractor approximately 100 yards. When I...

So, I broke the lever on my 1720 that puts the tractor in and out of 4wd. It pulled up and broke the stop and went past the stop so it wouldn't go in. I took it to the shop and they diagnosed...

I have a Ford 1720 between 92-95. Would like to know if anyone would know the Specs for the head torque and valve settings. Any help would be appreciated. Thanks.

I have a 1988 3 cylinder diesel Ford 1720. It starts in seconds and runs great the first 15 to 30 minutes. The RPM's then drop off sharpley and fluctuates up and down barely running, limping back...

I need to replace some grease zerks on my rock shaft and the loader. Does anyone know the size? Are they threaded or push in type? Thanks!

im new here, recently bought a 1720 4x4 with turf tires and im needing help on getting the right size ag wheels, and info on where i can get a set front and rear, letting me what ur sizes are...

Hello everyone. New to the forum. I have a ford 1720 SSS and when I pull up the lever to engage the four wheel drive I get a lot of trans noise - very loud in 4th gear-high range and not normal...

Fired up my 1720 Turbo to snow blow today! When it's 3 degrees outside and your body parts are freezing that extra power is really nice when you want to get the job done quickly. When pushing it...

Hey all, This will be my first full winter with my Ford 1720 diesel and I am looking for some sound advice. Some have warned that I must start treating my fuel due to low temperatures. Is this...

Considering buying Ford 1720 in very good condition with loader, cab and finish mower. Would like input on type and size of snow blade this unit can handle for a church parking lot. Also, frame...

Hello All, Well winter is just around the corner here in Minnesota and now is the time to prepare while the weather is still decent. I have a 1989 Ford 1720 that I purchased last spring and I...

I submitted a review for my 1720 on 2 occasions with acknowledgments that it was received but still no review posted. Tim

Can anyone tell me what type power steering fluid goes in a Ford 1720 tractor,

New me to Ford 1720 ford, the RH steering arm and spindle splines have been used loose and it is extremely sloppy, front tire has a lot of play, any trick to tightning these up or do I need to...

I need a front grille for my 1720, but all I can find listed on line are grilles for a 1710...will that work? Many Thanks!

Hi, I've got a line on a ford 1720, 28hp tractor and I'm wondering about it's ability to plow a field. Doe it have enough jam to pull a plow? I've only got about 5 acres to plow and once I've...

I looked at a Ford 1720 today, 725 hrs, decent paint and sheet metal ( some rust, but not excessive ). It cranked well, no excessive smoke, and all gears and lift worked. It has 4 FWD, REV, and...

Hi, just wondering if anyone out there has a used 60" 4 pin bucket in good shape that they would like to sell that would fit a Ford 7108Q loader which is being used on a Ford 1720? Or, do you...

I am looking for a set of used AG tires and Wheels for my FORD 1720 4x4 TRACTOR. I have Turf tires now and might be willing to trade depending on what you have. I think the size of the AGs would...

Hello, I am going to look at a 1989 Ford 1720 this weekend. It has a 7108QT FEL and a Ford 715 3pt blower. I have talked to the owner and he said everything runs as it should. No issues to speak...

Hello all, Can anyone tell me how big of a job it is to change out the glowpugs in a Ford 1720? I don't have a manual so any advice would be appreciated. If anyone has any photos of the procedure...

Hi, I am looking to purchase a 20 year old Ford 1720, 4wd, 2950 hours on it, and with a Ford 7108 loader attached. I found one that I am interested in and have talked to the owner about it. I...

Hi, I am looking to purchase a Ford 1720, 4wd, 2950 hours on it, and with a Ford 7108 loader attached. I found one that I am interested in and have talked to the owner about it. I would...

Hi all, Just joined the forum and appreciate all the good advice you folks have. I am looking to purchase a Ford 1720 with a Ford 7108 loader on it. I found one that I am interested in and have...

Looking for a tractor for clearing & excavation work. Found a 1720 w/ a FEL & backhoe. I'm a little more familiar w/ Kubotas so I wanted to know how this tractor would compare to a L series. Size...

Looking for a tractor for clearing & excavation work. Found a 1720 w/ a FEL & backhoe. I'm a little more familiar w/ Kubota's so I wanted to know how this tractor would compare to a L series...

Hi guys! The draft control on my 1720 has stopped working. Have any of you other Ford CUT owners had this problem? I use this little tractor for so many things that I hadn't really noticed the...

i am trying to locate a website or somewhere that i can order a replacement ignition switch for my 1720. local tractor parts store wants 124.21 for swith with wiring harness and 123.21 with out...

not sure year, but i think its a 1989, 4x4. my stepdad needs to know it the rear axle housings are interchangable. for what ever reason he wants to swap the right side with the left side. also how...

I am looking for some sheet metal for my trusty Ford 1720 tractor. I need the hood and I also need the part that is in front of the driver and the steering wheel comes from. Mine looks kinda...

My 1720 has started making noise when the clutch pedal is let out. It does this in gear or not in gear. Depressed it makes no noise at all when let out it makes a knocking sound that seems like...

When I take out the clutch of my 1720 whether in gear or not it makes a knocking noise. When the clutch is pushed in the noise vanishes, when it is let out it makes the noise. I do not see any...

I had taken my loader bucket off for the winter to attach my front mount snow blower. Upon reattaching the loader bucket at the beginning of spring. I cannot get the one return line to work...

Hello.I looked at a ford 1720 with 7108 loader and factory heated cab today.It seems very clean 1500 hours, no dents,didnt smoke when started.(it was about 22 degrees this am) dealer asking$...

Hi, I recently got a 1720 that has been seating for a while. I am having problems starting it and I will like to go through all the wiring key points to make sure there is not a bad contact. I...

Hello everyone I just purchased a 1989 1720 with 1100 hrs yeah.Now I would like to add rear hydraulics for a log splitter and a corn planter/w one way cylinder.The tractor doesn't have any rear...

Found this on a used car lot.It's 6.5' x 16' and has brakes on rear axle.All it needs are new fenders and I found a local trailer parts place that has them for $40.00 each.When I weld them on I...

Picked up my tractor on the way to hunting lease last Thursday and I had it stuck by noon Saturday.I got in to a small area of high ground (surrounded by swamp) where I mowed between a few white...

We picked up a 1988 Ford 1720 that's having issues. The first thing I noticed after opening the hood is that the battery positive terminal cable is connected to the frame. Could a 1720 really be...

Hello, I need to replace the rear axle seal on my 1720. From the parts breakdown, it looks like I need to remove the wheel shaft case, remove the nut from the end of the axle, pull the axle out...

Just curious if anyone has used this type of manual? Ford New Holland 1120, 1220, 1320, 1520, 1720, 1920, 2120 Tractor Repair Manual - FO-46 or dealt with this company. I am looking for a...

I have a Ford 1720 four wheel tractor, that has a leaking front spindle seal. I know years ago I had done one side, and I can remember that it was as bad as I thought to replace.On the other hand...

I recently bought a ford 1720 I see a hydraulic manifold under right side with three tubes connecting to the loader joy stick, i assume one is inlet and one oulet return from joystick, what is...

Hello, Hopefully someone can help. I just purchased a 1995 Ford 1720 with 950 hours on it. The machine is exceptionally clean, it even has the paper labels from Ford intact inside the wheels...

I am considering the pruchase of a 1720 2wd. This particular tractor is in near perfect condition with 428 hrs. It is sold with a woods 48" bush hog. The askinbg price is 6,900.00$. I have driven...

Hey gang, I am considering something a little more powerful than my MF GC2300. There's a Ford 1720, manafactured in 1986 with 2255 hours on it. They're asking $10,000 for it. I know nothing about...

...where is the hydraulic reservoir and how do I check the level and fill it? I have looked for it and without any luck. I am guessing the age to be about 1990 or so. The previous owner has a...

Brand new tractor owner here. Bought a house in rural southern Georgia and it came with a Ford 1720, two wheel drive, with a few attachments. The closest I've ever come to having a tractor...

I have a ten year old ford tractor model 1720. It is 27.7 hp. With a 7.4 gpm hydraulic. I am looking to upgrade from my woods 750 hoe to a 9000 model from woods. The dealer says that its too big...

The alternator gave out the other day , and since the local dealer was closed I stopped by NAPA to see if they could cross reference the alternator (just on the off chance they had something in...

I spoke to the local NH dealer today and he wants $572 for the kit to add a rear hydraulic hook up to my Ford 1720. All I want to do is run a log splitter, so figure I'll just buy some hose and...

Help! How do I engage the PTO on a 1993 (?) Ford 1720 without grinding the gears?

Could someone please post a link to a good picture (or set of pictures) of a Ford 1720? Thanks, Cliff

Hello Everybody, I am the one who was asking questions about rebuilding a Ford 1720 engine. See: Engine Overhaul My question is; does anybody have or know where I might be able to find a good...

My 1720 started to run very rough, and was hard to start. I changed the fuel filter, and the problem persisted. It would trun over and never fire up, someitme it would fire up, but would idle and...

I have two tractors that I want to trade in on a new Boomer and would like to know what their worth. The 1720 is in like-new condition but is 12 years old. It has always been stored indoors. It...