Just another junk chainsaw

[xyz123]

Mamma said get what you want for Fathers day.


So after talking with guy one the cheap 36" bar he was running. I ordered me a 42" for use for stumping and big cuts.

Plus ordered it in 3/8 058 since I have 2 rolls of it here already to make my own 135DL chains with.

Also got a Farmertec G2511 Joncutter coming. Another 2511 echo clone for 99 shipped from US warehouse. Cheap as I have seen the echo clones.

Already have all the set up on hand too. .325 Nano, 1/4" mini micro, 3/8LP

 

[xyz123]

Maybe today I might break down and stick that full wrap 357 359 346 353 handle on. Out of the 3 saws I have it will fit.

Think it will go on the Corey Cory Fabcorp ported 359.

 

[xyz123]

Making a 3/8 135dl Farmertec full skip chain.

had to improvise since chain scale I use only went to 123dl 3/8.

Hopefully fits the bar with 8T rim or will have to add a link or go 7T

For G3120

 

[xyz123]

Shop music

 

[xyz123]

42" 3/8 bar I ordered from MI, arrived while out on lake yesterday.

Hopefully get a chance to check if my 135DL chain I made fits with 3/8 8T rim.

 

[xyz123]

Farmertec 3120 with full skip 3/8.

135DL 42” bar and 3/8 8 rim leaves plenty adjustment.

For that every once in awhile need of a bigger saw and b+c.

Not even crazy priced as a whole set up.

 

[xyz123]

Can never have to many of the little 25cc saws. Farmertec G2511 aka Joncutter G2511 echo 2511 clone.

Just like the V-modest one so far comparing and looking over in Farmertec colors.

12" to 42" covered, 25cc to 119cc

3/8LP 1/4" mini 325 Nano all 3 sets now to compare at once for fun.

I swear it crawled up beside the G3120 and said daddy.

 

[xyz123]

 

[xyz123]

Tiny compared to biggie.

12" to 42" geter done.

 

[xyz123]

Echo clone 2511 25cc just started 2nd tank and only $99 bucks shipped stock. From US dealer or US warehouse in NJ.

 

[xyz123]

Going put my other oregon 325 Nano set up on the Joncutter 2511 by Farmertec and see if any gains in cut time over my best 3/8LP full chisel I ran on it. The 25cc seem to really like the nano 325 043.

1/4" mini micro the smoothest for pruning. But is also the slowest cutting of the 3 tested.

 

[xyz123]

Liking the Farmertec version of the 2511.

Guys said putting Egan pipe on seen good gains too. Close to 30% they said.

Only thing got to cut cover on clones.

Friends that is going to port this one and ordered another for stock to compare.

 

[xyz123]

Farmertec 2511 clone version is nice. $99 shipped from US.

Comes with 3/8LP 12" but throwing a Oregon Nano set on for some testing also.

 

[xyz123]

Seen this morning. Some were calling it the storm trooper. I can see that.

Others called it the man bun edition.

 

[xyz123]

Timing the new Joncutter 2511 open port with their stock open muffler with small pipe. Put on the nano set up.

Then ran the OEM echo 2511 closed port with the Egan pipe that tested 28% better stock then the echo stuffed mufflers they use on them. Also new nano set up.

Cutting clean cant pine dry 8x8 which is around 9" round.

Fastest cuts there was only 2 seconds difference. 20% difference in cuts between them. I am almost betting the clone would beat the oem if it had that awful stuffed up stock muffler on it.

Not bad for a $99 shipped saw compared to over $500 saw.

 

[xyz123]

Broke out the new 2511 clone Farmertec to cut up a decent limb blown out in storm. 2 pulls pop on choke next started.
Only reason used it was get some time on it checking over.

I should buy more these ones. But how many 2511's does a guy need.

 

[stevem5215]

I have three here and that's too many! 4 if you include the pole saw (used it yesterday for a high broken set of branches in a Oak)

 

[xyz123]

I counted my runners only the other day when a friend ask. I am down to 25 now. Thats a good thing honestly.

Year so ago was around 30.

I been way way higher then that back when I was racing etc. 2010 when I stopped chainsaw racing. I sold 10K worth of saws in first year selling off.


Collector types like when I sell because I dont collect saws. All have a use or FS to locals.

 

[kenmbz]

Had most of the top of a maple tree fall onto my path to my neighbors house Friday night.
With the pole saw was able to save the newly replanted trees that this mass of branches fell on.
Used it to cut the hanger from the tree and then dive into the branches to cut the ones putting pressure on the little apple tree.
The cage was mangled, but somehow the tree didn't snap.
When I have some time will get the cs490 out to finish, I think the biggest branch can't be more than 8" on the end,
When asked why we have so many saws, using a regular saw to cut 6-8' up into a mass of branches would have meant the loss of three trees. All saved using the pole saw.

 

[xyz123]

What pole saw you got?

I wish I hadnt sold my PPT260 echo one.