digitalwoodshop
New member
- Joined
- Oct 22, 2019
- Messages
- 2
- Tractor
- TurfCat
So I am new to this Jacobson TurfCat T423D. I have had it over 3 years and had it serviced when I first got it.... But... My "Belly" was too big to fit behind the wheel... So 55 pounds later since March and a different seat I finally got it cutting.
Is there an option to swing the front deck higher to work on the blades? Without damaging the hoses...?
I have a deck jack but have not opened the box yet.
I have considered building a Gravel Ramp from 4 x 4's and gravel to winch it up the ramp to allow better access under the deck as it would be overhanging the ramp 4 feet off the ground. Winch not drive it up...
I posted in the parts area I am looking for a lost Spindle bottom center blade bolt 500895 Ref 21. It is out of stock.
Going to try a metal detector where I lost a blade cutting... rookie move... I had hit some gravel on the crown of a grass road and I am not sure if I sheared the shear pin and the center bolt spun out... Or I sheared the center bolt head off.... Need to look at the spindle...
Was looking for Spindle Bearings just to have them and found a part number 4121994 I believe but it did not cross to anything... Then the page went 404... Gone... In EZGO I found them as 350759 and in stock.
Is there a better forum to look for help on my TurfCat?
Still have more weight to loose... 195 more... Using the mower to cut walking paths. The light weight pipe is not a ROPS but was to help me get my Fat ***** out of the stock seat.... First time I sat in it I got stuck for 20 minutes.... Sad... I know... but making progress... TMI... Too Much Info.. for a 2nd post..
Lots of good info found in a search... I noticed the Throttle Creep too.... From full to 3/4.... Saw that posted too... Had to push it back to full about a hundred times in a 3 hour cut...
For now I had to bypass the Safety Circuit and wire a fused switch to K6 the Mower Relay. It has been intermittent... Seat and High Low also bypassed when I got it. Not sure if the Delay relay needs contacts cleaned.... Are the relays under the Steering wheel? Don't see them in the parts breakdown.
AL
Is there an option to swing the front deck higher to work on the blades? Without damaging the hoses...?
I have a deck jack but have not opened the box yet.
I have considered building a Gravel Ramp from 4 x 4's and gravel to winch it up the ramp to allow better access under the deck as it would be overhanging the ramp 4 feet off the ground. Winch not drive it up...
I posted in the parts area I am looking for a lost Spindle bottom center blade bolt 500895 Ref 21. It is out of stock.
Going to try a metal detector where I lost a blade cutting... rookie move... I had hit some gravel on the crown of a grass road and I am not sure if I sheared the shear pin and the center bolt spun out... Or I sheared the center bolt head off.... Need to look at the spindle...
Was looking for Spindle Bearings just to have them and found a part number 4121994 I believe but it did not cross to anything... Then the page went 404... Gone... In EZGO I found them as 350759 and in stock.
Is there a better forum to look for help on my TurfCat?
Still have more weight to loose... 195 more... Using the mower to cut walking paths. The light weight pipe is not a ROPS but was to help me get my Fat ***** out of the stock seat.... First time I sat in it I got stuck for 20 minutes.... Sad... I know... but making progress... TMI... Too Much Info.. for a 2nd post..
Lots of good info found in a search... I noticed the Throttle Creep too.... From full to 3/4.... Saw that posted too... Had to push it back to full about a hundred times in a 3 hour cut...
For now I had to bypass the Safety Circuit and wire a fused switch to K6 the Mower Relay. It has been intermittent... Seat and High Low also bypassed when I got it. Not sure if the Delay relay needs contacts cleaned.... Are the relays under the Steering wheel? Don't see them in the parts breakdown.
AL
Attachments
Last edited:
