How to wire sewer ejector pump

[SkeeterFood]

Well, again I have to assume that you have a generator for running the pump when needed. Being off grid could also mean that you've gone with some form of alternative energy solution with a battery bank and converter, but your writings make me feel like this would not apply here.

I have other questions, but not sure exactly what to ask or how as there is still information missing.

I found a video about installing a grinder pump that covers all of the normal aspects. It does not cover temporary electrical connections, so that is what we need to work on here. Should be very easy to figure out that part. The video is here:
Grinder Pump Installation: Installing a 2 Series E/One Grinder Pump Station - YouTube

As for your tank, does it have a riser on it? If so, is it a dual lid design? What I mean by that is, when you take the lid off of your tank, is there another lid inside to make that upper area its own compartment? If not, then you need to have a junction box outside the tank. Haven't found much out there showing the length of wire on the Little Giant A-23, but it appears it should easily be able to come up and out of your tank. If this is the case, then the ideal thing would be to install your junction box on the outside of the tank. Now the question is, is this where you want your disconnect plug, and "why"? I ask "why" for a reason - if you cannot answer that question about every aspect of your operation, then you need to go back to the drawing board and find those answers BEFORE your work begins! As your tank is already installed and you still have questions, it appears you still have "why" questions to figure out......which is what we're trying to help you do here.

 

[kc5dlo]

Why did you select such a big pump? Sounds like a fractional hp 115 volt unit with a piggy back float would have been easier and cheaper.

 

[Cord]

The ejector line is 800' long with a substantial head.

 

[Tractor Seabee]

Don't you love those DIYers that get in over their knowledge base. I have tried to help some at the big box stores when the clerks are clueless on how things operate and/or are hampered by policy to not get into code and other perceived liability issues/details. Some are grateful, most have their made up and turn down help. There is enough ready information on the internet that is so often ignored.

Be that as it is may; we still want to help the OP. I under stand a little more of his install now. I assume it is the A1000 tank (that is a lot of sewage to Lay festering till pump starts. There is no indication of how the wiring gets into the tank. The power cord and float switch wiring will all fit into a 3/4" conduit. Probably easy to hole saw for a 3/4 Myers hub with nipple and seal off fitting and run PVC or flex conduit (depending on distance from there to the J box. Lot of ways to do that. I hope the OPs 800 foot run is downhill. Even his choice of pump may not cut a it if all up hill. I would increase the discharge pipe a bunch to over the pipe friction alone. Agree that a grinder pump is proper choice; even they are known to not grind up stuff city folks are used to putting down the drain. As already stated; do not put a junction box inside the tank unless you want to make immersion proof (expensive process). I would still put a high level float switch to give alarm when pump start is needed. Operating float switches get stuff caught on them and do fail as they cycle more often. Why chance an overflowing toilet. Don't forget to vent the tank also.

Remember this is armchair engineering with a half deck of 52 playing cards.

Ron

 

[geteh]

Have a remote cabin up north and I have an inspection coming up where I'll need the sewer ejector pump to function. For the record, this place is off grid and the inspector says no electrical permit is required. That said, I'll pay him a fee to come and perform an inspection just to make sure I did things right. The pump is a 2hp 220v grinder pump that is outside of the home. The pump is in a 300 gallon plastic tank. The tank lid is flush with grade. I've never wired up a pump like this so I'm a but confused as to how it's done. Per the instruction manual, there appears to be a junction box where the pump wires and float wires are connected to the service. From what I can find on line, this box would be a 12x12 plastic box and you bring a 2" conduit out of the box and then pull the pump and float wires through the conduit. The wires are then potted to seal the conduit. A electrical plug goes in the box and the pump gets plugged into the outlet so the plug serves as the disconnect. Ok, that all makes sense Check Our Services. What I can't figure out how to bring a conduit from the outlet inside of a box through the tank wall. Anybody ever wire one of these? Pictures would be appreciated!

When wiring a 120V sewer pump with alarm, how many wires do you need to run?
I guess my question is how many wires for the alarm?

I was asked to quote for wiring one and don't know how the alarm wires. I do know it has to be on a separate circuit from the pump and from what little I know has to be plugged in at the house.

Is it just a single signal wire or what?

 

[grsthegreat]

I have wired hundreds of these. I use the orenco splice block with optional rubber gasket. You can order these with optional amount of wire connectors. Depends on number of floats you use. I usually install 3 floats. Off, run, alarm. But ive installed up to 5 if necessary. Also include one connector for motor wire.

There will be a 1” fitting where you place rubber seal and that is what goes thru tank riser. Than pipe to alarm controllar.


This is what i use.

Splice Kits

Splice Kits

www.rcworst.com

 

[grsthegreat]

There are all sorts of alarm systems systems out there. From basic with no operational controls, to advanced where you can manually run pump if needed without lifting septic cover

 

[grsthegreat]

Seriously… an 800 foot discharge. Ive never seen this length done. Even slightly downhill thats alot to ask of a pump on a solar system. And how many feet is the head distance, that is ti say how far uphill is it lifting before its discharged thru septic field.

In the past we've had ones with a large head distance. We had to install an additional 1000 gal tank 1/2 way up and place an additional pump lift station at that point to continue lift.

They have charts for every size pump. We generally use Zoeller pumps. Have not had great luck with little giant.