Home electrical question

[Jstpssng]

I'm bringing home a Craftsman planer/molder which was my father's. It runs on 220/15 or 20 amp, I don't remember which.
Eventually I will build my garage and set it up in there but for now need to hook up a temporary power supply. My place is wired for an electric range but I use propane. I am thinking about swapping the 50 amp breaker for the one which is proper for the planer, then building a 20 foot pigtail adapter to bring power out of the house.
Does this make sense, or sound like a good way to burn the house down?

Thank you

 

[SPYDERLK]

I'm bringing home a Craftsman planer/molder which was my father's. It runs on 220/15 or 20 amp, I don't remember which.
Eventually I will build my garage and set it up in there but for now need to hook up a temporary power supply. My place is wired for an electric range but I use propane. I am thinking about swapping the 50 amp breaker for the one which is proper for the planer, then building a 20 foot pigtail adapter to bring power out of the house.
Does this make sense, or sound like a good way to burn the house down?

Thank you

Yes. No problem. Use 12-3 romex in a conduit. The wire itself in much easier to work with than direct burial 12-3 UF. Just make sure the cable is protected from damage where it transits the wall. If youre talking running the wire above ground you can protect it well using the ballistic nylon braided sheath tubing used on hydraulic lines.

 

[Jstpssng]

Yes. No problem. Use 12-3 romex in a conduit. The wire itself in much easier to work with than direct burial 12-3 UF. Just make sure the cable is protected from damage where it transits the wall. If youre talking running the wire above ground you can protect it well using the ballistic nylon braided sheath tubing used on hydraulic lines.

Thank you. I thought it made sense, but have a knack for doing things wrong.

 

[MAX-24-Dean]

Swap the breaker out with a 2 pole 20 amp also. Protection at the proper ampacity for those number 12 conductors on the extension of the circuit.

 

[LittleBill21]

Thank you. I thought it made sense, but have a knack for doing things wrong.

are you talking about just the breaker or the wire as well. I assume you mean just the breaker, 50amp wire is not going fit under a 20 amp breaker. does it have a built in circuit breaker?

 

[MAX-24-Dean]

Cheapest method to splice conductors while preserving wire length.

You can use a two hole mechanical lug.

Commercial Electric 14 AWG to 1/0 AWG Dual Rated Mechanical Lug with 2 Conductors and 1 Hole Mount (2-Pack) G99012 - The Home Depot

Commercial Electric's Mechanical Lugs are used to create a secure and reliable electrical connection between electrical conductors, such as wires or cables. Mechanical lugs can be either bolted or crimped

www.homedepot.com

Connect wire from (Edit) the range circuit 50 amp breaker in panel (Remove 50 amp breaker and replace with a 20 amp to protect the #12 conductor size) to one side of the mechanical lug or a split bolt, Then use a short #12 to connect from the lug to the new 20 amp breaker.

Wrap the lug with electrical tape, then the linerless rubber splicing tape. Then wrap with electrical tap again.
It may look like a ball of tape when you are done but it is safe.
Reason for using electrical tape in the first wrap is so that you can take it apart easier when the time comes.
The splicing tape is very sticky once it is in use and will mold into somewhat of a single piece that will not unwrap the same way it went on. Best to cut with a knife to disassemble.

Scotch 3/4 in. x 30 ft. Linerless Rubber Splicing Tape 41717-BX-10 - The Home Depot

Provide immediate moisture seals and void-free buildup by selecting this durable 3M Scotch Linerless Rubber Splicing Tape.

www.homedepot.com

If using split bolt connectors, use the same tape layering method.

If your panel is close to where you want to use the planer, you could just take the circuit directly from the panel.

 

[LittleBill21]

Cheapest method to splice conductors while preserving wire length.

You can use a two hole mechanical lug.

Commercial Electric 14 AWG to 1/0 AWG Dual Rated Mechanical Lug with 2 Conductors and 1 Hole Mount (2-Pack) G99012 - The Home Depot

Commercial Electric's Mechanical Lugs are used to create a secure and reliable electrical connection between electrical conductors, such as wires or cables. Mechanical lugs can be either bolted or crimped

www.homedepot.com

Connect wire from 50 amp breaker in panel to one side, Then use a short #12 to connect from the lug to the new 20 amp breaker.

Wrap with electrical tape, then the linerless rubber splicing tape. Then wrap with electrical tap again.
It may look like a ball of tape when you are done but it is safe.
Reason for using electrical tape in the first wrap is so that you can take it apart easier when the time comes.
The splicing tape is very sticky once it is in use and will mold into somewhat of a single piece that will not unwrap the same way it went on. Best to cut with a knife to disassemble.

Scotch 3/4 in. x 30 ft. Linerless Rubber Splicing Tape 41717-BX-10 - The Home Depot

Provide immediate moisture seals and void-free buildup by selecting this durable 3M Scotch Linerless Rubber Splicing Tape.

www.homedepot.com

If using split bolt connectors, use the same tape layering method.

If your panel is close to where you want to use the planer, you could just take the circuit directly from the panel.

yea, this is the way to go, forgot about split bolts, even though i use them, cheapest and easiest way to go.

 

[Jstpssng]

are you talking about just the breaker or the wire as well. I assume you mean just the breaker, 50amp wire is not going fit under a 20 amp breaker. does it have a built in circuit breaker?

I intend to change the breaker in the box, wire size shouldn't matter.

 

[plowhog]

Use 12-3 romex in a conduit.

I am not an electrician, but I thought you never use romex inside a conduit?

 

[Notforhire]

I am not an electrician, but I thought you never use romex inside a conduit?

You are correct.