scott_vt
Super Member
- Joined
- Oct 5, 2004
- Messages
- 7,606
- Location
- east wells,vt
- Tractor
- 1986 MF 1040, 1942 Farmall A, 1949 Farmall Super A
Good morning!!!!
- Thread starter 300UGUY
- Start date
- Views: 18774486
Buppies
Super Star Member
- Joined
- Oct 26, 2011
- Messages
- 12,421
- Location
- SouthWestern Virginia
- Tractor
- Kubota L5240 EX mark 60 in 29 hp Toro 60inch Z Master 21 inch walk behind Polaris 900 hunter edition 30in toro walk behind
Nice plowhog another car guy
scott_vt
Super Member
- Joined
- Oct 5, 2004
- Messages
- 7,606
- Location
- east wells,vt
- Tractor
- 1986 MF 1040, 1942 Farmall A, 1949 Farmall Super A
Good Morning,
Vt,52 to start going to 75, with sunny skies, some lingering fog laying in the valley ! Yesterday we had on and off showers, mostly dry but every time a dark cloud passed we would get some sprinkles !
Planning on more shop time this morning after breakfast. I need to make the pieces that attach to the inside of each leg and then cut a 6 degree angle on each leg. That is what gives the back legs the splay when assembled.
Ron, curious what type of equipment you have for sheet metal ! When I was a modelmaker at Pitney Bowes, I had the shears and brakes for bending, really miss all of that !
Plowhog, glad to hear that Rigby doing a bit better with other dogs !
Hope all have a great Tuesday!
Vt,52 to start going to 75, with sunny skies, some lingering fog laying in the valley ! Yesterday we had on and off showers, mostly dry but every time a dark cloud passed we would get some sprinkles !
Planning on more shop time this morning after breakfast. I need to make the pieces that attach to the inside of each leg and then cut a 6 degree angle on each leg. That is what gives the back legs the splay when assembled.
Ron, curious what type of equipment you have for sheet metal ! When I was a modelmaker at Pitney Bowes, I had the shears and brakes for bending, really miss all of that !
Plowhog, glad to hear that Rigby doing a bit better with other dogs !
Hope all have a great Tuesday!
Attachments
ronjhall
Super Star Member
I have a 24” welding table. With a 3/4” thick table top. C Clamp sheet metal down with a 1 1/4” bar. Then bend it with another bar by beating it with a plastic impact mallet. This method works good for metal up to .60”. When I was working I had access to tools to do the bending. Picture shows the 2 guards. Items 60 and 70. $142 and $111 at Messick’s.
Ron, curious what type of equipment you have for sheet metal ! When I was a modelmaker at Pitney Bowes, I had the shears and brakes for bending, really miss all of that !
buckeyefarmer
Epic Contributor
Sorry for your loss. RIP.
buckeyefarmer
Epic Contributor
Scott, beautiful view there.
Popgadget
Elite Member
Good Morning
59° with a high of 78 under clear skies for today.
Yesterday was a busy day at the old folks home, spray foam, masons and outside trim work all going on simultaneously.
The insulators have to finish the great room so the masons can get going on the fireplace, hopefully early today.
I put the 90” landpride on the tractor and mowed inside all the pastures, then trimmed the edges with the Lazer. So all the mowing is done for now.
There’s already signs of life out there, I’ll walk out in a few to see what’s happening so far. Once that’s all settled I’m going to get breakfast with the professor.
Might even get back to the little plane if these guys are all under control.
Tomorrow I’ll be in Roanoke for most of the day, I got a call from someone that needed a copilot for the day in a jet that I’m rated for, so I figured I might as well.
It will be fun not being in charge, hopefully I’ll behave…..
59° with a high of 78 under clear skies for today.
Yesterday was a busy day at the old folks home, spray foam, masons and outside trim work all going on simultaneously.
The insulators have to finish the great room so the masons can get going on the fireplace, hopefully early today.
I put the 90” landpride on the tractor and mowed inside all the pastures, then trimmed the edges with the Lazer. So all the mowing is done for now.
There’s already signs of life out there, I’ll walk out in a few to see what’s happening so far. Once that’s all settled I’m going to get breakfast with the professor.
Might even get back to the little plane if these guys are all under control.
Tomorrow I’ll be in Roanoke for most of the day, I got a call from someone that needed a copilot for the day in a jet that I’m rated for, so I figured I might as well.
It will be fun not being in charge, hopefully I’ll behave…..
buckeyefarmer
Epic Contributor
Got down to 55° last night.
Finally got estimate to repair the geo unit, I said to do it.
Mixed up and sprayed more weed juice yesterday.
Finally got estimate to repair the geo unit, I said to do it.
Mixed up and sprayed more weed juice yesterday.
txdon
Super Star Member
So sorry for your family's loss Wngsprd.
Good morning! 77ËšF heading to the upper 90s, S wind, no chance of rain in the 10 day forecast.
Have appointment with doctor tomorrow to schedule shoulder surgery.
I need to mow the yard this morning before the 90s set in.
Good morning! 77ËšF heading to the upper 90s, S wind, no chance of rain in the 10 day forecast.
Have appointment with doctor tomorrow to schedule shoulder surgery.
I need to mow the yard this morning before the 90s set in.
