Emmet vintage
New member
Hi just wondering all the steps i should go through when changing the coolant on my 20?
Any reply appreciated
Any reply appreciated
Ferguson 20 coolant flush and change
- Thread starter Emmet vintage
- Start date
- Views: 21342
OP
Emmet vintage
New member
Anything at all would be great as i'd like to get this done before the cold weather really sets in 
murphy1244
Super Star Member
- Joined
- Nov 25, 2011
- Messages
- 16,336
- Location
- Ohio
- Tractor
- Kubota 1120 RTV Kioti DK-40, MF-135, Ventrac 4500Y
Get it to Temp and drain and refill with 50,50 mix.:thumbsup:
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
if you want to go whole hog, after you drain it. backflush the block and radiator with your garden hose. heck.. might even sacrifice a gallon of vinegar in there with some water and a few more minutes of run time.. then drain and flush.
pre mix your af 50/50 and refill. run to burp.. and top off.
if theremo or hoses and belt looks bad. this si the time to replace them.
pre mix your af 50/50 and refill. run to burp.. and top off.
if theremo or hoses and belt looks bad. this si the time to replace them.
OP
Emmet vintage
New member
Ok will tackle that job tomorrow thanks for the replies
OP
Emmet vintage
New member
Another question. The breather on the left hand side of the tractor what is the proper way of cleaning this?
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
oil bath air claner.. it will have metal floss in it. some models are easy to remove.. some not. if the removeable floss style. celant he canister in solvent.. floss too. reassemble.. oil and go. solvent like kero, mineral spirits or diesel.
can submerge the entir thing in a parts washer and slosh around if it is the style hard to take apart. again. drip dry.. then oil and go
can submerge the entir thing in a parts washer and slosh around if it is the style hard to take apart. again. drip dry.. then oil and go
OP
Emmet vintage
New member
Ok cheers any other maintence you would recommend for the winter?
any other maintence you would recommend for the winter?
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
the usual.. oil and filter change. check coolant. top off and charge battery to prevent freezing.
air tires. .. winter is a good time to repack front wheel bearings and adjust axle nut.. lube all zerks.. etc.. reset points.. clean up electrical.. this way she's ready to go when needed. ( adjust brakes too! )
air tires. .. winter is a good time to repack front wheel bearings and adjust axle nut.. lube all zerks.. etc.. reset points.. clean up electrical.. this way she's ready to go when needed. ( adjust brakes too! )
OP
Emmet vintage
New member
Most of tht is done except the brakes. Just out of curiosity how hard would it be to get the tractor starting with a key (currently starting on the gearstick)
