Doing Some Road Work

/ Doing Some Road Work #1  

crash325

Elite Member
Joined
Feb 9, 2011
Messages
3,999
Location
Tucson AZ
Tractor
New Holland TC-45
It's been a couple of years since any work has been done on our dirt road. Couple of years ago some grading was done and some fill added. Being dirt with a lot of traffic, the road ruffs up fairly fast.

This year we are trying to do a little more. But as normal $$$ are very limited. No one has to chip in $$ or help with the work. As normal some folks think they deserve a good road and will not work or pay.

Big problem with a dirt road, the better the road, the faster folks drive and the faster it gets torn up.

The old road grader in the picture costs $750 a day. Pictures shown were early on the 4th day. He was real close to where I was working when the wheel & tire blew off. Sounded almost like an explosion. I tried to lift the axle out of the dirt with my FEL. When the tractor was on 1 wheel it still had not budged. Spent about an hour or a little more jacking it up, then putting the chain & boomer on it. The operator drove the grader about a mile and I carried the wheel (Cast Iron) & tire hanging off my FEL. I don't know what it weighs but the links in my 1/4" chain stretched out a little.

Next day the owner / operator brought out a smaller "Fiat" grader, nice little machine and works good.

There is 1 spot that turns into a lake about 50' wide and up to 3 feet deep. At present I'm digging a "T" or funnel shaped drain. Going down 18" to 2' and a little over 2' wide where they come together. Rocks don't look that big in the picture, but there are quite a few 2 large to fit in the BH bucket.

The tractor at an angle is a little more angled than it looks. I'm depending on the rear tire laying against the bank to stay upright and not laying on its side.

I would like to know what year the old grader was built. Tried looking on the net with no luck. Maybe 1 of you folks can help.

More later if anyone is interested. The "Fun" will continue tomorrow.
 

Attachments

  • grader 1.jpg
    grader 1.jpg
    99 KB · Views: 211
  • grader 2.jpg
    grader 2.jpg
    98.7 KB · Views: 176
  • grader 3.jpg
    grader 3.jpg
    67.9 KB · Views: 158
  • grader tire.jpg
    grader tire.jpg
    90.7 KB · Views: 186
  • cat serial.jpg
    cat serial.jpg
    53.5 KB · Views: 160
  • ditch 1.jpg
    ditch 1.jpg
    125.3 KB · Views: 194
  • trenching 1.jpg
    trenching 1.jpg
    141.3 KB · Views: 244
/ Doing Some Road Work
  • Thread Starter
#5  
Model 12 1947-59 is as close as I can get, based on the 8T prefix of the serial number.

Graders

Thanks Dean,
If I read the chart correctly it's a 1950 machine.
It appears to be all original except for some repair items. Engine very healthy, pony motor fires right up.

Pretty good condition except for the tires and glass missing from cab.

Thanks Again,
Jim
 
/ Doing Some Road Work #6  
A grader can usually jack itself up just by running the blade out the side near the flat tire and hitting the down lever. Even an old tired beast should have been able to take most of the weight off that tire.
 
/ Doing Some Road Work #7  
crash325 said:
Thanks Dean,
If I read the chart correctly it's a 1950 machine.
It appears to be all original except for some repair items. Engine very healthy, pony motor fires right up.

Pretty good condition except for the tires and glass missing from cab.

Thanks Again,
Jim

Oh that's great! I didn't scroll on down towards the bottom. (iPhone :):) ). Glad to help.
 
 
Top