I have a ford 4630 which has run well over the past 10 years. I changed the oil in nov. 2011 and filled it to the top of the dip stick mark. Started the engine and let it wet the new filters etc, stopped it and let it sit for a while and rechecked the level and all was good. The next week I went to use it and the level was 1 inch above the full mark. The oil looks good not water in it etc. but the engine now blows white smoke. Drained out almost a gallon of oil to put it to the right level, one week later again above the mark. Is it possible the fuel pump is leaking diesel into the oil? or is it some other place it is leaking diesel into the oil?
Changing oil level
- Thread starter JayKoska
- Start date
- Views: 1361
Deano
Veteran Member
If the oil is not milky, then it should not be water or coolant. Does the oil smell like diesel??
Also, gotta ask, are there any of your buddies pulling a "prank" on you?
That sounds like a lot!!
Deano
Also, gotta ask, are there any of your buddies pulling a "prank" on you?
That sounds like a lot!!
Deano
Bigfoot62
Veteran Member
- Joined
- Aug 5, 2008
- Messages
- 2,283
- Location
- W. Central Louisiana
- Tractor
- JD 5090M; JD 5085M; JD 5083E; NH TN70A; Ford 2600
It's coming from somewhere. (I know, that's just over-stating the obvious)
If it were coolant, the oil should have a milky appearance. Since it does not, (you said) I would bet on diesel fuel. IIRC, the 4630 does have a mechanical "lift pump" that just pressurizes the fuel going to the injector pump. That would be the first place to look. If the diaphram is leaking, that would allow fuel, under pressure, to go directly into the crankcase. It could account for your increase in oil level.
If it were coolant, the oil should have a milky appearance. Since it does not, (you said) I would bet on diesel fuel. IIRC, the 4630 does have a mechanical "lift pump" that just pressurizes the fuel going to the injector pump. That would be the first place to look. If the diaphram is leaking, that would allow fuel, under pressure, to go directly into the crankcase. It could account for your increase in oil level.
clemsonfor
Super Member
Id put money on the injector or fuel pump leaking into the crankcase. Which would depend upon gas or deisel, but i assume its deisel. I just skimmed all the posts here though did not read all of any of them.
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
if it's not drinking hyd oil from an engine mounted pump I'd be inclined to think it was diesel.
Diamondpilot
Super Star Member
- Joined
- Jan 18, 2007
- Messages
- 16,316
- Location
- Daleville, IN
- Tractor
- Jinma 254/284 Ford 861 Powermaster at work
Yep, either hydro oil from a pump seal or a injector/pump issue.
Chris
Chris
pjbci
Platinum Member
- Joined
- Feb 10, 2012
- Messages
- 780
- Location
- Summit. Ms
- Tractor
- JD 4840, Deere 5075e, 450j, Cat D4k2, Kobelco 160, Volvo EC140el, deere 310, komatsu D31px22, IH 1486, MF 135, MHF TO35
Its fairly common for those mechanical fuel lift pumps to do that. Ive had a couple leak into the crankcase over the last 10 yrs or so. Although its possible it could be your injector pump, just not as likely.
