Air Compressor Water Drain??

[monteu]

I have had my new compressor with a 80 gallon vertical tank installed for a couple weeks now. I had put off checking the drain valve to see if it had water in it. Surprise, this evening I drained around a gallon of water. It has no drain system installed just the little spigot at the bottom. There is not much clearance between it and the floor so I am going to have figure something out. What are you all doing for air compressor drains? pictures? thanks a lot

 

[BeezFun]

I ran my drain out the wall of the shop, put a quarter turn valve just inside the wall and an elbow pointing down at the ground outside the wall. You'll also want to add a water trap in the line right after the compressor to make sure you get out as much water as possible before it hits your tools.

 

[lmalcomb]

here is what i did:
Air Compressor Automatic Drain Valve

 

[shortthrow50]

Gallon? you serious!!!??? IT would take a year for my 80 gallon to accumulate that much. thats crazy

 

[mvwicker]

I have had my new compressor with a 80 gallon vertical tank installed for a couple weeks now. I had put off checking the drain valve to see if it had water in it. Surprise, this evening I drained around a gallon of water. It has no drain system installed just the little spigot at the bottom. There is not much clearance between it and the floor so I am going to have figure something out. What are you all doing for air compressor drains? pictures? thanks a lot

Ideally, drain it after every use. For my 30 gal tank that yields a splash on the cement floor that dries into groovy blast pattern. If you have enough water in your tank to create a puddle, then you aren't draining often enough.

 

[adjusterr]

I have an 80 gallon Devilbiss unit, I tipped the unit on it's side, removed the little drain valve and installed a 90 degree elbow, then ran a piece of galvanized pipe out past the bottom of the tank and installed a very small ball valve. Every time I get near the compressor I open the ballcock valve, out comes the condensation.

 

[dstig1]

I have an 80 gallon Devilbiss unit, I tipped the unit on it's side, removed the little drain valve and installed a 90 degree elbow, then ran a piece of galvanized pipe out past the bottom of the tank and installed a very small ball valve. Every time I get near the compressor I open the ballcock valve, out comes the condensation.

Exact same thing I did, and exactly how I handle it. every time I walk by I give it a quick shot (might be daily, might be 2 weeks if I am not using it).

 

[Bird]

Ideally, drain it after every use. For my 30 gal tank that yields a splash on the cement floor that dries into groovy blast pattern. If you have enough water in your tank to create a puddle, then you aren't draining often enough.

I agree.

I have an 80 gallon Devilbiss unit, I tipped the unit on it's side, removed the little drain valve and installed a 90 degree elbow, then ran a piece of galvanized pipe out past the bottom of the tank and installed a very small ball valve. Every time I get near the compressor I open the ballcock valve, out comes the condensation.

I just have a 30 gallon upright rigged the same and I do the same as far as draining it. The only problem is that the elbow makes the drain just a tiny bit too long. It's supposed to be a portable compressor with wheels, but since I never move it anyway, I raised it a bit with wooden blocks.

 

[Ken45101]

Tractor Supply has a drain kit with a 90 degree ell, a straight piece, and a valve for under $20.

Make sure if you start adding any piping or fittings that they are rated for the pressure, you do not want an shrapnel flying around the shop.

Ken

 

[Storm56]

Exact same thing I did, and exactly how I handle it. every time I walk by I give it a quick shot (might be daily, might be 2 weeks if I am not using it).

Yep, I have a Quincy and that is what I do.

 

[radioman]

I took the little spigot off and checked size and when to my local lowes and got an elbow, pipe, and ball valve with a garden hose adapter. I used a old scrap garden hose to route the hose outside so when I turn it on, I dont get any water all over inside.

 

[ray66v]

How much water you make depends on what kind of compressor you have, how you use it, and what conditions you use it under.

If you live where it's humid, and your compressor runs enough to get pretty hot all the time, your going to make water lots of water.

The best option is an electric solenoid operated, automatic drain like this: Electronic Air Compressor Tank Drain - TP Tools & Equipment.

You can set the amount of time it will be open, and how often, for you individual situation, and then worry about something else.

There are lots of different versions.

I drilled a hole in the concrete and stuck the drain hose in. That way, the mess ends up under the floor.

These valves are not cheap, but neither is a new tank. And they don't make tanks that last anymore.

A cheap box fan blowing air on the compressor, also helps to keep water production down.

 

[Pete6114]

I have a automatic drain on my Quincy. When the compressor kicks out, some air shoots out the drain, taking moisture with it

 

[Ken45101]

A cheap box fan blowing air on the compressor, also helps to keep water production down.

I fail to see how a fan blowing on the compressor will change the amount of condensed water vapor ends up in the compressor tank.

 

[ray66v]

I fail to see how a fan blowing on the compressor will change the amount of condensed water vapor ends up in the compressor tank.

The fan helps keep the pump cool, if the pump stays cool, it doesn't heat the air as much.

In order for air to condense water, it must be cooled. If the air does not get real hot in the first place, it won't cool, or cool as much, when it gets to the tank. If it doesn't cool, it doesn't condense.

 

[Bird]

The fan helps keep the pump cool, if the pump stays cool, it doesn't heat the air as much.

In order for air to condense water, it must be cooled. If the air does not get real hot in the first place, it won't cool, or cool as much, when it gets to the tank. If it doesn't cool, it doesn't condense.

I'll take your word for that, but if the water doesn't condense out of the air in the compressor's tank, does that mean the moisture is still suspended in the compressed air, and you get more moisture through your air hose and into your power tools?

 

[Ken45101]

The fan helps keep the pump cool, if the pump stays cool, it doesn't heat the air as much.

In order for air to condense water, it must be cooled. If the air does not get real hot in the first place, it won't cool, or cool as much, when it gets to the tank. If it doesn't cool, it doesn't condense.

I don't think so. How hot the air gets in the pump doesn't matter. What matters is the ambient temperature, the amount of moisture in the air, and the pressure in the tank. Air can hold less moisture at 100 psi than it can at atmospheric pressure. Air can hold more moisture at 150 degrees than it can at 90 degrees and even less at 70 degrees. When the air in the tank cools, the excess moisture will condense out.

 

[ray66v]

When the air in the tank cools, the excess moisture will condense out.

So, you see that the air has to cool to condense, but you don't see the benefit of not heating it in the first place. :confused3:

I had a entire career working in a shop, to find out what worked, and what didn't here. If you don't agree, don't put a fan on your compressor, I don't care.

 

[Qapla]

Regardless of how the temperature affects the air/water ratio, when water accumulates in the bottom of the tank it needs to be drained.

Like others, we added a galvanized 90 at the bottom of the tank and ran the drain outside. We dump the water outside instead of inside. When you live in Florida, you get water in the tank every time you use the compressor. If you use your compressor everyday, drain it every day. If you only use it occasionally, still drain it after each day's use.

 

[ericher69]

Will try the fan suggestion.


When using my shop air for cabinet blasting I get plenty of water production. I will often go drain the tank between cycles and also drain the dessicant air dryer.

Yet still get clogging issues with the sand after a while.