Has been restored and was running well. Now need to harvest 2 acre corn plot, but tractor will not idle and runs rough; the governor surges - up and down. Removed governor and found nothing wrong. Have boiled and soaked carburetor for possible clogged passageways to no avail. Somehow seems like it is not getting enough gas but the gas line lets plenty fuel thru. Really frustrated!
1953 John Deere 60 - restored to operating condition but now having problems
- Thread starter siebaldo
- Start date
- Views: 5518
-
- Tags
- john deere 60
DJ54
Elite Member
- Joined
- Jan 20, 2009
- Messages
- 4,579
- Location
- Carroll, Ohio
- Tractor
- IH Farmall 656 gas/ IH 240 Utility/ 2, Super C Farmalls/ 2, Farmall A's/ Farmall BN/McCormick-Deering OS-6/McCormick-Deering O-4/ '36 Farmall F-12/ 480 Case hoe. '65 Ford 2000 3 cyl., 4 spd. w/3 spd Aux. Trans
By any chance were any of the parts sandblasted near the fuel tank..? Hood, etc..?? Did you take the inlet strainer out, and check it..?? I'd also check the atomizer nozzles, and see if there may be something plugging those itty bitty holes. Does partial choke make a difference..??
Taking out the drain plug in the botom of the carb, should assure you you are getting plenty of fuel past the float needle valve, and the float not sticking.
If a spec of sand in plugging a port, all the soaking in the world will not make a difference.
Was the manifold removed? Maybe a intake gasket leak there..??
I have heard them run a little rough when the throttle shaft bushing was worn, and allow extra air in, but smoothed out under a pull.
Guess it depends on how thorough of a restoration was done. Cleaned, prepped and painted, or complete overhaul included. Could be some cleaning unsealed something, that was covered with gunk, and allowing too much air in.
Taking out the drain plug in the botom of the carb, should assure you you are getting plenty of fuel past the float needle valve, and the float not sticking.
If a spec of sand in plugging a port, all the soaking in the world will not make a difference.
Was the manifold removed? Maybe a intake gasket leak there..??
I have heard them run a little rough when the throttle shaft bushing was worn, and allow extra air in, but smoothed out under a pull.
Guess it depends on how thorough of a restoration was done. Cleaned, prepped and painted, or complete overhaul included. Could be some cleaning unsealed something, that was covered with gunk, and allowing too much air in.
grnspot110
Elite Member
- Joined
- May 16, 2007
- Messages
- 2,672
- Location
- MO
- Tractor
- John Deere 1944- H, 1961 Cub Lo-Boy, 2016- JD 2025R, 2018- JD X580
You might try: Two-cylinder Plus at Conway, MO!
jimmysisson
Veteran Member
- Joined
- Jul 11, 2005
- Messages
- 2,358
- Location
- W.Mass
- Tractor
- 1993 NH 2120 (the best), 1974 MF 135 (sold, but solid), 1947 Farmall A (bought, sold, bought back, sold again), 1956 MH50 lbt (sold, in 1980, darn it)
Water in the gas or tank? Good luck.
Jim
Jim
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
try a tug of choke. not full choke.. but some, when the governor goes hunting.
if choke helps.. look for a fuel restriction. whether it be a lean main circuit.. or blocked fuel supply / tank vacume.. etc..
if choke helps.. look for a fuel restriction. whether it be a lean main circuit.. or blocked fuel supply / tank vacume.. etc..
