1952 Ford 8N 302 v8 conversion

   / 1952 Ford 8N 302 v8 conversion
  • Thread Starter
#91  
Working on my 8N Awesome Henry 302 V8 conversion. Still have not got the motor running.

Plan was to start it today but we ran into what we thought might be a ringgear problem even though Don at Awesome Henry says this has never caused a problem and all his flywheels are built this way.

Starter howls - the awesome henry ringgear has the almost square cut towards the starter drive gear.
Shouldn't the beveled side of the ringgear face the starter drive gear?
Could that be the source of the howl?

This happens whether the motor is bolted to the tranny or not so the eliminates the pilot bearing.
Happens with old and new starter. Starters run quiet off the tractor.
No bolts are hitting anything and motor turns freely by hand with the plugs pulled.

Problem Solved!!!

I have the 164 tooth manual flywheel with the auto old style starter and I just figured out the problem. The kit included a 3/8" spacer to use the auto starter on the manual flywheel. Turns out I needed a 5/8" spacer. I tested my theory with a couple of washers and the howling went away. The inside of the bendix was touching the front of the flywheel when it spun out in the active mode. Nothing that 6 hours of debugging, disassembly, reassembly, repeat 5 times couldn't solve.
Turns out the cut of the ringgear teeth was not the issue.
 
   / 1952 Ford 8N 302 v8 conversion #92  
Sweet! Overcoming some frustration adds to the feeling of accomplishment. Looking forward to seeing some video of it moving.
 
   / 1952 Ford 8N 302 v8 conversion #93  
to bad the kit didn't have that info!
 
   / 1952 Ford 8N 302 v8 conversion #94  
Working on my 8N Awesome Henry 302 V8 conversion.

Problem Solved!!!

I have the 164 tooth manual flywheel with the auto old style starter and I just figured out the problem. The kit included a 3/8" spacer to use the auto starter on the manual flywheel. Turns out I needed a 5/8" spacer. I tested my theory with a couple of washers and the howling went away. The inside of the bendix was touching the front of the flywheel when it spun out in the active mode. Nothing that 6 hours of debugging, disassembly, reassembly, repeat 5 times couldn't solve.
Turns out the cut of the ringgear teeth was not the issue.

+++++++++++++++++

It's a great feeling of satisfaction, when you can figure stuff like that out.... Genius, pure genius........

Dave
 
   / 1952 Ford 8N 302 v8 conversion
  • Thread Starter
#95  
Awesome Henry V8 302 conversion Starter Problem and fix
No genius here, some say I am just very persistent!!
Here are the pix of the problem and the fix.
StarterSwirl.jpg StarterSpacer.jpg

Note: I also enlarged the top mounting hole by 1/16" on the starter itself as the starter drive gear was awfully tight to the ring gear. This allowed me to pivot the starter just a smidgeon away from the ring gear.

Thanks for all the support and assistance.
Merry Christmas to everyone and to all an "N" night
 
   / 1952 Ford 8N 302 v8 conversion
  • Thread Starter
#96  
Oh Oh, can't get spark out of Mallory 8555101C billet distributor and it did not come with a wiring diagram, it is meant for a car connector. Anyone got any knowledge of these?
 
   / 1952 Ford 8N 302 v8 conversion #97  
Does it have an internal coil... You may need an external coil.... and resistor... Now you know all I know..... almost nothing...

Dave
 
   / 1952 Ford 8N 302 v8 conversion
  • Thread Starter
#98  
It does have an internal coil. There are three wires coming out of the distributor, brown, black & red. These go to a connector block under the built in coil. There are 5 terminals under the connector block. We are trying to figure out what goes where? We think black out of distributor goes to ground, not sure about rest. Couldn't find any good diagrams at mallory or google.

Does it have an internal coil... You may need an external coil.... and resistor... Now you know all I know..... almost nothing...

Dave
 
   / 1952 Ford 8N 302 v8 conversion #99  
I couldn't find ANY diagrams or schematics... Are there any symbols where the wires enter the housing...
 
   / 1952 Ford 8N 302 v8 conversion #100  
Found one.... hope it helps...... Dave

Next post.....
 

Attachments

  • Mallory schenatic 001.jpg
    Mallory schenatic 001.jpg
    477.5 KB · Views: 502

Tractor & Equipment Auctions

2011 Manac 36245B30 45ft T/A Walking Floor Trailer (A50323)
2011 Manac...
2011 Toyota Sienna Van (A50324)
2011 Toyota Sienna...
2018 JLG 3246ES 32ft Electric Scissor Lift (A50322)
2018 JLG 3246ES...
(2) Firestone 320/85R24 and (2) Galaxy 25x8.50-14 (A50120)
(2) Firestone...
2013 Kubota M9960 (A50120)
2013 Kubota M9960...
2020 New Holland 105 Workmaster MFWD Compact Tractor with 632TL Front Loader - Poultry Special (A52748)
2020 New Holland...
 
Top