seal

I'm about to begin repairs on a TMG 72 inch tiller....I purchased it used and the gear box input seal is leaking and possibly the gear drive box seal is as well....in my town there are no ag dealers. I can drive to a Kubota dealer 30 miles away but my question is will a seal from NAPA or...

Had dry asphalt laid in part of driveway. Being a loose asphalt, is there a way to seal it by spraying. If I pour the liquid sealer and use a push broom it will move the loose top layer. Is there a spray method? Thanks

Hey all! You do not have to purchase any special tools or pay a shop to install these difficult to install seals. Here is an easy DIY I found and had my mechanic watch it and perform the procedure. It does seem easier if the vice jaws are smaller. I think the best twine/rope to use is a smooth...

I looked in many places for a walkthrough for my particular equipment however I didn't find one that was 100% the same. Many tutorials and videos showed 80% similar steps but there were nuances that weren't the same, like the wire retaining clip. Eventually I came to a point where I felt I had...

Has anyone replaced these seals? Both mine are leaking badly and must be replaced. I need a "how-to" lesson please.

I'm needing to source complete seal kits for all of the cylinders on my MF 30B, but having a bit of trouble. Boom cylinders Bucket cylinders Steering cylinders Is there anyone out there with prior experience and/or a service manual that might be able to tell me what part numbers/distributors I...

I currently have the tractor split replacing the clutch. There seemed to be a lot of oil in the housing, and on the back of the fly wheel. I'm thinking it may be the crankshaft seal. How difficult is it to relieve the seal? I just can't seem to find any info on replacing the crankshaft seal. Is...

This is the sealer the cover over the drive chain. It is like over $100 for the OEM part. Looking for a cheaper alternative and can't seem to find the same edge seal anywhere.

The passenger side rear axle seal is leaking. Does anyone know where I can get a replacement seal / part number? Possibly a bearing as well. I’m wondering if the bearing could be getting bad causing the seal to fail.

Hi I got a Gravely commercial 432, and it leaks on the left, I'm having a hard time to find that seal. Anyone knows a site I can order from ?

Need to replace the front crankshaft oil seal on my 2006 Kioti CK30HST. I have a service manual but is very vague.I looks like I have to remove the front gear cover in order to get at the seal to replace it. Was wondering if one could pull the seal without removal of the cover? Does anyone have...

Looks to be time to replace one of the knuckle seals since it's leaking pretty good now. Just ordered the seal and the process looks pretty simple, any concerns dropping the lower axle housing or just have at it.

Gc1715 rear pto seal part number

Seasons greeting all. I posted my intial tie rod breakage inquiry in the General Repair forum, but realize now I should have posted here. To preface my current situation, here is a link to that post for some history...

My T554 PTO seal started leaking. Had it replaced by non-dealer. Later I was talking to the dealer about it and he said I will tell you why the seal went out. He said there is a vent hose hanging down near the PTO, and dirt dobbers plug up the hose and this will cause the seal to fail. I went...

Hello all, Guys i am looking for a Lift cylinder seal for my Shibaura D23F tractor. by the looks of it when i lift it leaks pretty bad on the left side ( looks to be a blue seal at the top of the cylinder ) i just cant seem to find anywhere online that sells them. If any of you guys know where i...

Well folks, had both FEL seals replaced in the spring. The right hand side was dripping. So I figured OK, get both done. Used a local guy in Victoria has his own hydraulic shop. Here we are maybe 40 hours later and today I see a wet booger forming on the fitting. Only thing I can think of is...

I brought in the tractor to install the grapple and I asked the dealer to diagnosis a small leak in the rear end of the tractor. They diagnosed it as "rear seal leak" and $800 plus fluid cost to repair it. I am trying to confirm and better understand what exactly is the "rear seal" - is this...

Hydraulic mower. I've rebuilt the motors that power the blades several years ago. Discovered I've got some dampness UNDER the deck....so something is leaking. Not a blow out leak but leaking none the less. (first start this spring, mower was VERY low on oil and I was baffled as to where it...

My John Deere Model A has a leaking left axle seal. Any idea the cost for repari? Any idea where I can get a replacement?

Got tall grass wrapped around and now the seal is leaking. How big of a project for 2 people, advice and suggestions?

Just replaced my LW8 backhoe seals but NOT including the main rod seals which I couldn’t remove and seemed in decent shape anyway. For those replacing the rest being: rod o ring under the rod piston, both gland large o rings, gland wiper and the gland U cup oil seal (most important), See the...

Looking at my valve to hydraulic line face seal Jinma o rings I measure these as 2x8(id) sealing o rinos. I believe a 90 Shore durometer hardness o ring is required for sealing… but maybe not. Not sure on this. So, I’m wondering if I get the 90a or is a 70a o ring ok? I assume Viton or bunta...

While I was replacing my axle seal on my F15D, the tiller sprung a leak. I replaced seals on both sides, and both sides the seals were in horrible condition. They were shredded. The bearing on the right side was shot, too. I updated the bearing with an 2RS series to help prevent the elements...

I have a Kioti LK2552. Its been a work horse. But today I noticed oil leaking from the starter. Looking online - it sounds like a leaky rear main seal. Does that sound correct? If so, the tractor would need to be split to replace it. I assume I am looking at $5,000+ to repair?? I am not sure...

Well, it happened. Leaking axle seal. I haven't done one of these jobs before. I can't find a LS or New Holland dealer near by, and I just don't want to drive an hour each way for a $17 part. Looks like Messick's has it in stock. So, while I'm elbow deep in the hub is there anything else I...

Hi folks, I have a 14 year old 800hr BX1860 on which I've just discovered the propeller shaft front joint cover (aka dust boot) (item 20 below) has worn through and fallen off. Interestingly, the damaged boot was just sitting atop the MMM deck which I had pulled off for springtime blade...

I have a 7195 Cub Cadet with a bad front swivel seal. I checked all the online parts dealers with no luck. They all tell me it’s obsolete. Does anyone know of another place or what can I do besides keeping it full of oil. Need help. Thanks

We are replacing the double seal behind the bearing set but we also noticed another shot rubber seal on the other side of the side transfer box toward the shaft. I don't see any mention of this nor where I can order a replacement? Can anybody who has taken one apart advise?

Hello, 2010 RTV500 (approximately 100 hours) I'm having trouble removing the oil seal from the differential. I have the CV assembly removed. Does anyone have any advice? Bonus question is to how/why the seal is leaking. The cv joint doesn't appear to have any damage.

I have a leak on the plate on my power steering pump on my 2120. The seal kit is $185. Cheapest I can find. I can get a new pump for just a little bit more. Anyone know a cheaper way to get this seal? It's an odd shaped seal so idk if a hydraulic shop could come up with one. Or if I'm gonna...

Power steering pump is leaking between the rear plate and the housing. The seal kits are discontinued. And it's an odd shaped seal. Any chance some good rtv on the flat bit will work? I have attached pics of where it's leaking in the yellow circle and a pic of the plate off and the seal.

I decided to do this myself. I couldn't find any videos on it but I found it really wasn't that difficult. Here is the video I posted. If anyone has leaks or needs info on how to do it check out the video or ask here and I'll see if I can give some good info:

Hi, Need help with high-quality cylinder parts & seals, tried this website - www.fpeseals.com, can anyone suggest other websites in the UK to explore

HI, I need to replace the axle seals on a Iseki TXG23. In the manual it looks like an outer and inner 'snap-clips' are used to hold the axle in. Does anyone know if this is correct or are there another fixing inside the gear/differential lock assembly that are holds the axles in. I have tried...