power steering

Started pushing fluid out under the steering wheel...got frustrated by what I researched on replacements and seal kits available ..took it out tore it down found the inner shaft seal obliterated or close...it was a rigid seal just like the outer shaft seal...was able to make a replacement with...

Can some one give me an idea of what the average thickness of the shim between the worm gear assembly and the pedestal is on the power steering assembly for a two cylinder John Deere? I tried following the procedure in the power steering service manual but I just can't see how the thickness of...

Stop Error On T4.75, Low Power Steering Pressure / Transmission Pressure 2019 Powerstar 75 Symptoms Day started out with all running good, no apparent problems, then STOP error comes up along with a symbol on the display that closest resembles the low pressure, and steering wheel. However I...

I have case jx1090u. The power steering and the front loader have a tendency to stop working in below freezing weather i asume there is water in the oil, but i can t find where to check and or empty and or refill. All tips are welcome.

I have case jx1090u. The power steering and the front loader have a tendency to stop working in below freezing weather i asume there is water in the oil, but i can t find where to check and or empty and or refill. All tips are welcome.

Im trying to determine the best way to add power steering to my 1020, whether it be retrofitting something or tracking down a factory setup. If anyone has pics of the powersteering setup on their 1020, i would appreciate you posting them to give me an idea of how it’s supposed to go together...

Gday I am working on a Ford 4000 with a power steering assist Ram on it the owner pulled it off and took it to the local shop to repair leaks when he got it back it didnt leak but oil gets very hot within 30 minutes too hot too touch! I have played around with adjustment and it all works well...

Looking for advice as how to proceed, steering loss was after repairs to front axle. Had leak(s) at front axle, left side was seal at “knuckle.” Right side replaced: knuckle seal, final drive outer bearing and seal. Job went well, even for my experience level; no stranger to busted...

Hi from a German Yanmar Owner, I've been reading here and at the Hoye forum for a couple of years now. I own a YM1510d since 2020 and I'm very happy with this little powerful tractor. I bought the tractor from a dealer who mounted already a FEL. Back in 2021 I updated the maual steering to a...

I have rebuilt power steering pump and steering column and still will not turn what what could be my problem? I have not put a pressure gauge on it yet. Ford 545

my north track 254 tractor the steering is hard, one way and then eases up in power steers properly. When you go to steer back, it locks up again. I’ve changed the oil clean the screen have flow to the piston. I took the diverter valve apart and cleaned it everything seems to be good there. all...

So me and my neighbor use a 1970s era Massey 31 industrial logging tractor it has a new power steering pump (gear drive off the front gears of the engine) new hoses and cylinder, it steers fine when you first fire it up and take off but once the engine and pump get warm you have to lift the nose...

Ok, I have a 74 (or 73?) MF 135 orchard. Diesel. A couple weeks ago I was tilling my garden and busted a power steering line on the left side from the piston to one of the fittings under the steering column. Had my hydraulics shop make me a new hose (actually just went ahead and replaced...

My 1958 641 didn't have power steering so i decided to purchase a used one and put it on. All of the pieces arrived and got them on my tractor. When I started the tractor the line coming from the pump going to the gear box blew out a piece of rubber tubing. The old tubing had been patched with...

I am looking for parts or an entire pump for my Ford 800. It is a Thompson Products Inc. pump model P-1072. Any help on parts or resources would be greatly appreciated.