not working

I have my kubota b7200 that i have had a hard time getting to start. Turns out the glow plugs aren't working. I tried jumpering around and sending voltage strait rhough. I'm getting voltage, but according to my thermal camera, no heat at all. I can't imagine all 3 dying at the same time, so i'm...

As I’ve posted in another thread, I found that the seat safety switch had been bypassed. Today I decided to remove the bypass and use the seat safety switch. So, I removed the bypass jumper and plugged the safety switch connectors back together. It was a bit difficult for me to get to the...

I have a 2008 KUBOTA BX24 that I recently had serviced. The hour meter worked when I took it in. They delivered it back and now the hour meter is all a bunch of numbers not giving a true reading? Like just a bunch of random numbers. So I told them take it back. I had checked out on line that...

Good day Have a couple issues but first issue trying to figure is why glow plugsare not working. Tractor has rebuilt engine with new glow plugs. Noticed in another thread someone posted a picture and in it shows two 70 amp Handouk relays. My tractor has both plugs but nothing is plugged in...

...apparently. I.e. only one wheel spins when "engaged". Where do I look, or can I, to find out what the issue might be? B3030

The front axle is leaking fluid and the front wheel drive stopped working. If I continue to use tractor in 2 wheel drive will it do more damage to the front axle. Wondering if I could or should remove front drive shaft. Any thoughts would be appreciated. Thanks Len

I just purchased a Boxer 525dx mini-skid steer with 950 hours that has a hi/low switch that needs to be set in the “hi” position for increased ground speed when traveling, or for maximizing flow to a trencher or auger. The hi/low switch summary from the operator’s manual is attached. The...

The parking brake light hasn't working from day 1. When I turn on the ignition, the light comes on briefly on the dash, but it is not operational when the parking brake is actually applied. I didn't think anything of it till I forgot to disable the parking brake before using it one day. I...

We have a New Holland TS 110 and pto knob lights up but pto does not engage. We were told the pto solenoid is bad. Does anyone know where the solenoid is located.

I have an older Shaver HD8 post driver hooked up to a Ford 4000 that is not working. The cylinder does not want to extend on its own. If I push up helping it a bit and pull single spool valve lever back the cylinder will lift slightly, approx. a couple inches to a foot. After that when I push...

Well my favorite toy..my 2538 might have an issue. It only has 238 hours on it of dragging my driveway, spreading crush and run on the same, and brush hogging my 2 acre field. I spread 20 tons of crush and run the other day. I noticed some metallic sounds while I’d grab a load from the pile...

Hello. I have a 2019 4044R with 610 hrs on it and the ground speed and cruise control are not working now. No light comes on for cruise when pushed. Wondering if anyone else has had the same issue? And if so what the fix was. Thank you!

Anybody dealt with fuel gauge and tach not working? what was the fix?

Dash display got flooded and not working. Anything to check first before replacing at cost of $1200? Checked fuses and seem good Any way to check that power is getting to the unit?

Hi. Semi-Newbie Here. Have read through the forums without being able to find an answer to my particular issue. (But have found a lot of other great stuff I didn't know!) Issue I have is that the back mower implement will not raise. It did last season. Brought it out of storage. Changed the...

New owner of 2008 3038 tachometer not working - all fuses are okay. Hr meter works . Whats next?

Below is a picture of the 3rd function valve on my RX7320. I haven't used the 3rd function in over a year. I attached my grapple yesterday. It opens, but won't close. The solenoid thing in the picture has another just like it on the bottom side of the valve. That's the one that controls the...

I have a 230 that has a small cyclinder on each side to steer with. I recently changed fluid, filled with hyd 46 fluid. Now no steering at all. Do I need to bleed> If so, where> I cracked a hose at small steer cylinders and it squirts a little fluid here and there, not a stream. What am i doing...

New to me B2150. Going thru everything as a few things were neglected by previous owner. Oil pressure light doesn’t come on with key. Pulled dash hoping it was bulb, but bulb confirmed good. Sending unit or something else? Are they a generic item or Kubota only part? Appreciate any thoughts!

I purchased a 5520, the instrument cluster is not working. I sent it to be tested and it works fine. I've had a mechanic work on it extensively with no success. The cluster has rpm, fuel gauge and temperature gauge. I'm considering just adding aftermarket fuel and temperature gauges. I'd love...

About 3 month ago I changed out the loader control valve on my Kioti LK 3054 and after that my three point doesn’t work anymore. I’ve tried changing the seals in the three point cylinder turning off the loader controls with the shutoff valve to put all the pressure to the back and nothing seems...