long 445

Every time I start this tractor from COLD, its extremely difficult...cranks over before it finally kicks in to almost flattening the battery. In fact generally I need to put the battery on the charger and swap it for the spare just been charged each morning. It was built in the 80's and is...

Ok so I replaced my fuel filters and primer doing routine maintenance, and all the gaskets are in the right place, and I went from bleeding the filters to the injection pump to the injector lines and I just cannot seem to get the air out. I've repeated the process probably 25-30 times. And can't...

Ok so I have a long 445 diesel. It has run great, cranks up as soon as you turn the switch. But I pulled it in the shop to do some maintenance, new fuel filter and primer. And while it was in there put some fuel additive to keep it from jelling. But now it won't crank. Motor turns just as before...

Hey guys. Been reading for years. Usually can fix stuff no issue but my experience working on this old girl is limited. I have a. 1976 long 445. My father purchased it around 1978. Aside from a main bearing knock occasionally (since 1978) it's run reliably since for the family. When we...

I have recently purchased a long 445 and the 3 point will not raise or lower. Changed the fluid the fluid "which was really low and looked like oil". All I know is he said it slowly went out and now it doesn't work at all. Does anyone have any tips, or is there a secret way to operate them that...

I need a double clutch assembly for a Long 445. It has 10" discs. The plate has half inch mounting holes, with 3 fingers.

Hey everyone, new member and first post. I bought a long 445(project) for VERY cheap a few months ago. To explain what I've done to it will be a whole other post someday when I've got the time. For now, I've got to get this issue straightened out ASAP. I 瀘 supposed to be moving it and all my 3pt...

Hi, can anyone tell me how to adjust the valves on the Uzania 3 cylinder diesel engine. I don't know if they are to be at top dead center or a few degrees before or after and the clearance for each. I think some where in the range of 10-13 thos. on exhaust and 15-17 on intake or may be the other...

Have purchased some land and it came with 69 Long 445. Power steering did not work. Have rebuilt ram, installed pump and prince PRV. Upon start up wheels turn right an HD then pressure builds and fluid seals out of brass fittings installed on new pump and line connections. Have double checked...

Have purchased some land and it came with 69 Long 445. Power steering did not work. Have rebuilt ram, installed pump and prince PRV. Upon start up wheels turn right an HD then pressure builds and fluid seals out of brass fittings installed on new pump and line connections. Have double checked...

Hi I have a Long 445 DT. Has some problems. The 3 pt. hitch arms don't work. Removed everything to the short arms that connect to the crossbar. They don't seem to have any connection inside, they move up and down freely by hand. There is a clunking noise each time I lift the arms...

Good afternoon I have a Romanian built long 445. I recently took the top cover off the injector pump to replace two O-rings. I put things back the way I thought they should go and now I cant seem to get the throttle up. I believe this an issue with the governor but other than that I am...

Hey, I've got an older long 445 Romanian tractor with no rear lift at all. It slowly went away over a year or so with slow lifting and wouldn't hold up implements. I think I have pinpointed to the pump. When I removed the pump there was no oil at all in the pump or the lines connecting to it. I...

Please help, I bought a long 445 with FEL for $3000. I do not know how to change the 6 speed transmission from high to low. Also did I pay too much. Thanks

i have a utb long 445 i would say its a 74 model but not sure. i started having fuel smoke real bad less at idle if you bush hog up hill it is way under powerd it idles good will even idle up like its suppoused too but i hooked up a tiller to it in first gear idles up to 2300 rpm and it almost...

Hello, I recently bought a Long 445DT tractor. it is a UTB Fiat type tractor. It runs great drives great. it is a little "clunky" and not very smooth working but it works. Here is my problem, The 3 point hitch does not lift via the lever. It just floats to the top position. you can then...

I need a power steering pump for my Long tractor model 445, 4WD version. The pump appears to be a Borg Warner and as far as I can see it is model SR16B5CS43L. Or it might be R16B5CS43L. The stamping is unclear. It also has another number, 03001. Can anyone supply this pump? Maybe another...

I have a Long 445. It has a single hydraulic reservoir. The power steering, hydraulics, all work off the same fluid. My lift would not lift my bush hawg, so I changed the fluid, which was very milky. This worked fine for a few minutes and then it was back to not working. The more I used it, the...

:confused:Could someone please tell me if my tractor is a 445 or 460 Long ? The hood lifts to the front and it has headlights in the grille. I have been told by the guy I bought it from that it was a 445 long, but other people tell me it is a 460 Long. It has a six speed trans and I read on...

Problem is when I set the height of the 3PH it will drop and when I stop the tractor the implement will slowly drop. Any suggestions? Thanks

I have an UTB 445DT which is the 4WD version of the Long 445. This is a selectable 4 WD or front wheel assist arrangement. On mine the front axle can move forward or backward by over 1/8"! I could, for now, slide in a brass thrust washer to take up this slack, but its clear the trunnion bearings...

I inherited a repair project and am looking to find a head gasket, but more importantly specs to tighten everything back togeather. thanks dave a

I own a 1978 Long 445. The hyraulic reservoir in the frame collects moisture and forms an emulsion. I am getting ready to change the hydraulic oil. Does anybody have any suggestions on cleaning out the system(run some diesel through it?) and remeding the problem of condensation accumulation in...

HI All, I have a man who needs some parts for his Long 445. It has a D115 engine and the guy said it needs cam, lifter and gaskets. I have not seen the machine but this is what he said he needs. Thanks, Maka

Just thought I'd turn up some 3/4" pins on the lathe to fit a top link to my Long 445 ready to run a bush hog & mower I'm picking up Wednesday night. Pins are great & fit the top link easy, but cannot get them into the toplink support on the tractor. There are 4 holes for the toplink pin, but I...

Just thought I'd turn up some 3/4" pins on the lathe to fit a top link to my Long 445 ready to run a bush hog & mower I'm picking up Wednesday night. Pins are great & fit the top link easy, but cannot get them into the toplink support on the tractor. There are 4 holes for the toplink pin, but I...

Should the TPH arms power down as well as up on the Long 445? Mine lift fine, but won't come down without some weight on them. This is my first real tractor so I don't know if this is normal. If it ain't, where should I look to clean/adjust/repair?

I just bought a UTB ( Long) 445 DT (4 WD) which has a FEL with spool controls in the cab, plus a single rear hydraulic Q/D outlet. I want to run a back actor on this which has two hydraulic pipes marked in & out. Assuming the "in" pipe is connected to the rear outlet, where should I connect the...