john deere 355

So this morning I replaced the fuel filter on my John Deere 2355. Clipped in the new filter, loosened bleed screw, manually pumped the lever at the fuel filter until the air was mostly gone (couldn't quite get the bubble at the very top center since the bleed screw is on the right side)...

I've started having a shifting issue on my 1988 JD 2355, when I try to put it in reverse, it feels more like neutral (can't feel the gear through the gear shift) and about 95% of the time it won't back up. Both forward ranges and forward gears all work fine. It has a cab, so getting a good look...

So it's been pretty cold here, not quite polar vortex but cold (around 0 overnight, single digits daytime) When I started up my 1988 JD 2355 this afternoon (after being plugged in for about 2 hours, it was about 9 degrees) it started right up but the rpms started dipping occasionally. Started...

I have a 1993 JD 2355 that, in my opinion, is in good shape. It came with the farm I purchased back in 2012. My Wife's tractor (Kubota L5740) has a cab. She ran over a few wasp nests last year and became concerned about what would have happened it it had been me, on the JD, that ran over...

Ey guys, I think I know the answer to this but would like confirmation from those of you with much more experience than I. I have a JD2355 near me that me local town is auctioning off. It has only 1400 hrs and looks in good condition. The rear has no PTO or a 3pt. Can this be outfitted with one...

Included with the farm I purchased was a JD 2355 (1993 vintage). It has less than 1,500 hours on it. I changed the oil and have monitored the hydraulic fluid (wow, that stuff is tough to see on the dipstick). It has been running well. I've noticed some fluid weeping on the engine, but not...

Fluid everywhere where the brake pedals push the pistons into the huge block that I assume to me the master cylinder. Only appears to leak when running, and marks territory when parked after shut off. Havent cleaned all the fluid off to determine exact location, but believe it is seals around...

Any suggestions why? Rocks haft adjusted following technical manual New fluid, filter and screen Anything to adjust before opening rocks haft housing. Front end loader work well and strong. Thanks

1991 JD 2355, pto is slipping to the point that you can grab it and stop pto shaft with your hand. checked hydraulic fluid and it's good.Is there an adjustment and if the clutches need to be changed can this be done from the back or does the tractor need to be split. thx.

I am going to be looking at an 88 2355 4x4 w/cab I'm hoping someone could help with the controls What is the yellow lever on the left side of the dash? 4x4? What is the red handle on the right with the push button on top? PTO? It looks like there is a lever that slides left and right above the...

Using my 2355 today and the lift arms will not come down from up position. Tried moning the lever up and down many times to no avail. Arms stuck solid. Also tried moving the draft lever and the cut off needle valve and stil nothing. Thanks for help.

I have a JD355 with the 54C deck and 42" snowthrower that I am thinking of selling and I would appreciate anyone's input regarding a fair selling price. It is a 2000 model year with the 18HP Yanmar 2cyl diesel engine. It has just over 500 hours. I am the second owner, the first owner put...

I see an ad for a JD 2355 tractor with an 8 F 4 R transmission. I have never operated one but the tractor appears to be low hours clean and a decent deal. Too far to drive to check it out. I am use to my old '72 Ford 8x2 transmission but would like something a little faster changing...

I might have bought too big of batwing mower... Anyone have experience with the Bush Hog 2615 Legend, mine has michelin aircraft tires, chains and is heavy. I thought my John Deere 2355 FWA Cab tractor w/ loader could handle it now I have several people telling me that the mower might be too...

Anyone know of a good cheap source for a replacement seat for a JD 2355? Need to replace the entire seat assembly not just the cushions. Who has the best price and how do I find the actual part number of the assembly? Thanks in advance!

I am thinking about buying a 2355 4x4 with a 55hp pto rating. I am currently using a MM 670 with a 55-70 hp rated round baler, and can only make about 3/4 of a bale. I farm in hilly Pa. Will the 2355 be enough tractor for the job?? and in the furture I may go with a forage harvestor and wagon...